Showing results: 46 - 60 of 838 items found.
-
RLS-2100 -
Square Peg Communications Inc.
It is the most comprehensive, with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full motion support and integrated GPS simulators. It is the most flexible, providing end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. It supports the highest bandwidth and has an intuitive, user-friendly interface. And it does it all in one box.
-
SX-PCEAC-DB -
Silex Technology
The SX-PCEAC-DB is an 802.11ac compliant dual-band 3x3 PCIe Mini Card. It is based on the Qualcomm Atheros QCA9880 chipset, designed to deliver wireless data rates of up to 1.3Gbps.
-
RTM3 -
Seismic Source Co.
The Remote Trigger Module 3, or RTM3 3, is a new generation of impact trigger device. It is designed to time synchronize a single seismic source unit with multiple seismic recorders. It can also be used to synchronize multiple seismic recorders. The RTM3 units use an internal high accuracy oscillator that is synchronized to GPS timing information. Each RTM3 unit requires an external GPS receiver with valid satellite information to synchronize the internal clock. Once the internal clock is synchronized the RTM3 can be used without any GPS signal for up to 10 minutes.
-
SX-PCEAN2 -
Silex Technology
This SX-PCEAN2 is a dual band PCI Express wireless module, featuring two stream MIMO technology and industrial temperature support with throughput up to 300 Mbps. It is an ideal solution for high performance applications based on the NXP i.MX6 platform.
-
CMPHEAD -
Rohde & Schwarz GmbH & Co. KG
The separate one-box tester and the R&S®CMPHEAD30 RRH concept allow short RF cable lengths for an optimal link budget in radiated test environments. This approach enables testing of fully assembled FR2 devices and RFICs with both IF and mmWave RF interfaces. The multi-band R&S®CMPHEAD30 covers all important FR2 bands
-
-
CFIP-106/108 -
SAF Tehnika, As
CFIP-106/108 is primarily designed for IP networks and provides Fast Ethernet interface with capacities from 8 Mbps up to full duplex 100 Mbps Fast Ethernet. In addition to that, CFIP-108 has a 4xE1 port for legacy equipment connectivity and for use in hybrid TDM/IP networks.
-
Kuhne electronic GmbH
. Internal filters provide high spurious rejection and image rejection. Due to low phase noise and high frequency stability of the local oscillator at 3000 MHz, the up converter is suitable for analog and digital communication systems.Typical applications are Multichannel Multipoint Distribution Systems (MMDS) using QPSK modulation and DVB?T or DVB?S systems. The output power of 20 mW can be increased to several watts by the use of an additional power amplifier.
-
RAN -
RadiSys Corporation
Break free from traditional restrictions of proprietary networks with Radisys Connect Open RAN protocol software and accelerate 5G deployments.
-
ATS-3100 RTS -
Astronics Corporation
Extend the life of your legacy radios while simultaneously supporting modern radio technology, both airborne and ground, with the ATS-3100 Radio Test Set (RTS) - the complete solution for military and commercial radio test.
-
Shoghi Communications Ltd.
Radio Reconnaissance and Jamming Station is monitoring and jamming of radio signals in the frequency range of 25 to 1000MHz. The Radio Reconnaissance and Jamming Station allows audio monitoring, technical analysis, monopulse bearing finding of the radio emission sources.The Radio Reconnaissance and Jamming Station is capable of scanning the VHF/UHF frequency bands to identify the various sources of radio transmissions with their signal parameters. Carry out direction finding (DF) of the source of the radio signals and generation of jamming signals of required waveform to carry out jamming.
-
Kuhne electronic GmbH
Is a radio beacon, whose purpose is the investigation of the propagation of radio signals. Most radio propagation beacons use amateur radio frequencies. They can be found on LF, MF, HF, VHF, UHF, and microwave frequencies. Microwave beacons are also used as signal sources to test and calibrate antennas and receivers
-
T-RX -
CCX Technologies
Streamline your avionics radio testing process with the CCX Technologies T-RX Avionics Radio and Pulse Tester. The T-RX is an all-in-one avionics tester that conducts 100+ tests on over 16 systems with only 1 device!
-
ACSRF-4040 -
Gemini Data Loggers Ltd.
The Plus Radio Ethernet receiver is required as part of the Tinytag Radio Data Logging System. It controls the transmission of data to and from the radio loggers: data received from the loggers is then sent to the computer for viewing with Tinytag Explorer radio software. If power to the computer running the system is lost, the receiver has a battery back-up which will maintain the mesh network until power is restored. This receiver plugs directly into a LAN removing the need for a computer in the area where monitoring is to take place. The receiver is powered using a plug-in Power over Ethernet adaptor (ACS-0041) which is supplied with the unit.
-
NRFM-1000 -
MES Innovations
Locate and Identify Hidden Radio Transmitters (Bugs) with our precision meter and included earphone.