-
product
Impulse Generators
HYPERLABS triggerable impulse generators create precise high-speed pulses with 50 to 100 ps rise time. They can be triggered by input from antennas and other signal generator systems.
-
product
120 A Manual Pulse Width Extender
TLP-12012A6
High Power Pulse Instruments GmbH
- Pulse width extender for the high current TLP/HMM test system TLP-12010A and TLP-12010C- 6 manual selectable pulse width: 5, 10, 50, 100, 200 and 500 ns- High pulse output current up to ±120 A- High performance and high quality components
-
product
Laser
BDL-SMN Series
*Pulse Width Down to 40 ps*Repetition Rate 20 MHz / 50 MHz / 80 MHz / CW (Switchable)*Free Beam Output or Single-Mode Fiber Coupling*Beam Profile Correction Optics*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*Fast On / Off / Multiplexing Capability*Synchronisation Input
-
product
High Current SMU Family 2000 A
AXC76xx
Generate very short, fully regulated current pulses from 2 ms to DC with up to 2000 A. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
product
FPGA Workbench and I/O Cards
FPGA Workbench software provides a complete development environment for building customized solutions based on Concurrent’s programmable FPGA cards. FPGA Workbench includes a powerful GUI for selecting and configuring a wide range of pre-developed data acquisition and industry-specific modules to meet your application requirements. The library of functional IP modules includes pulse width modulation, analog I/O, digital I/O, SENT protocol, encoder, ignition, injection, crank/cam shaft, wheel speed sensor and change-of-state.
-
product
Femtosecond Terawatt Ti:sapphire Laser System
MPA-XL
MPA-XL is a cost-effective terawatt Ti: sapphire amplifier system. It gives up to 200 mJ energy of the stretched pulse and further compression with 65% efficiency. A standard air compressor can be placed into a custom designed vacuum chamber.
-
product
RF Safety Monitoring
MVG EME Guard XS Radar
Specifically designed to alert workers operating near radar transmitters of RF exposures, the unique EME Guard XS Radar is an RF pulse measuring device. It continuously scans for short pulsed signals, and via its built-in alarm and visual system, alerts users whenever the acceptable limits have been exceeded. This RF Safety tool is extremely easy to use and creates a safer working environment close to radar antennas and other pulsed RF sources.
-
product
Dual Channel Clock Driver Card
PI-41400
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable fro...show more -
product
cDAQ-9188, 8‑Slot, Ethernet CompactDAQ Chassis
781424-01
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
50MS/s Single-Channel Arbitrary Waveform Generator
WW5061
Model WW5061 represents the next generation of products in the field of function, pulse and arbitrary waveform generators. This instrument is superior and far more versatile than any existing equivalent whether it is an analog or digital product. As a waveform source, this model can replace analog generators in almost every application.
-
product
Digital Delay Generators
Highland has introduced three unique features to digital delay generation: a "Queued Updates" feature allows time settings to be changed without corrupting ongoing timings; a "Train" feature allows multiple pulses to be generated from each trigger; and a "Frames" feature allows complex delay sweeps and pulse scenarios to be pre-loaded and rapidly executed. Digital delay and pulse generators are available in 1-6 channels, with square, Gaussian, and arbitrary waveshapes, and insertion delays as low as 10 nanoseconds.
-
product
Multi-Battery Tester
MBT-1
The ZTS Multi-Battery Tester (MBT-1) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
product
Pulse Holiday Detector
NOVOTEST SPARK-1
Pulse Holiday Detector NOVOTEST SPARK-1 designed to detect pits, flaws, and holes in different non-metallic insulation coatings (such as polymers, epoxy, bitumen, etc.) and is mostly used for oil and gas metal pipelines and other objects. The device can be used while the pipeline construction, operation or service. Tested coating thickness is up to 12 mm. Such tests are needed to evaluate the oil and gas pipelines corrosion protection reliability.
-
product
10 MHz To 6 GHz LAN Wide Dynamic Range Average Power Sensor
L2051XA
Frequency range of 10 MHz – 6 GHzLAN connectivity with a wide dynamic range of -70 to +26 dBm for small signal measurementsFast real-time measurement of 50,000 readings/secReal-time measurement with zero dead time to ensure every single continuous pulse is measuredAverage mode time-selectivity function allows full dynamic range for average and time selectivity average power measurementsInternal zero and automatic calibration saves time and reduces measurement uncertaintyA BenchVue software license (BV0007B) is now included with your instrument. BenchVue makes it simple to connect, control instruments, and automate test sequences
-
product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
782052-01
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
FieldFox Handheld Microwave Spectrum Analyzer, 18 GHz
N9937A
100 kHz to 18 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
product
PCI/PXI Timing Board
6602
Interface board for converting signals on a National Instruments PCI/PXI 6602 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channels can be used to measure frequency or period. Digital inputs or outputs can be substituted on channels that are not needed for timing purposes.
-
product
High Current / High Voltage Pulsers
DEI Division
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
product
Data Diver
MT-8006B
LCD display for dialing number, Caller ID, Clock and other informationIndicator for determining the Line service and speedHigh impedance monitor for data safe operation without disrupting existing traffic.Smart power saving enables battery life up to 6 months12 phone number memory for speed dialing16 dialing number memoriesTone (DTMF) and pulse operationUp to 32 digits phone number memory for speed dialing keyPre-dialing and last number redial functionPBX pause key, insert a PBX pause in stored numbersTelephone line polarity indicatorsLow battery indicationBacklight functionRJ-11 port for easy test leads changeRinger and voltage LED indicationAngled bed of nails and RJ-11 plug
-
product
Reflectometer
T-510
Techno Instrumentation (India) Private Limited
Pulse Echo, Impulse current and Decay methodprovided to get the distance to almost all typesof faults.Laptop based 15 inch display with user friendlyinterface for easy operation.Online support of experts to review fault graphs.Comparison feature of any 5 graphs for reviewand analysis to get more accurate results.Velocity of propogation(VOP) control makes iteasy to precisely pre-locate faults in cables withdifferent velocity.Automatic storage of more than 10,000 faultgraphs.
-
product
RF Transformers
Pulse continues to lead the way with a broad range of components that enable twisted-pair copper high-speed services to homes and businesses. Pulse components are also used in cable modems and the consumer electronics that provide home networking services. Our high-performance transformers support home phone line and power line networks. These transformers are designed to exceed ANSI and ETSI standards, and have excellent THD performance and small footprints.
-
product
Picosecond Lasers
PL2230 Series
The first commercial fully diode pumped high pulse energy mode-locked laser, producing 28 ps pulses with up to 140 mJ pulse energy.
-
product
Frequency Counters
Frequency Counters measure frequency, period, time interval, pulse width, duty cycle, frequency ratio, phase, and more. Frequency counter products include options that are compatible with Astronics/Racal VXI-2461C, which can be used for automated test aerospace and defense applications.
-
product
AC Calibration Standard
1U647-001
The 1U647-001 is a low cost calibration standard used to determine if a 1U632-100 or a 1U663-100 DMU requires factory calibration. Its portability makes it ideal for field-testing. The standard generates signals that simulate the aircraft’s resolvers, rotary variable transformers (RVTs), and linear variable displacement transformers (LVDTs). The unit also generates a pulse width modulated (PWM) signal, and routes the output of an ARINC 429 source to the different DMU input channels. The calibration standard connects directly to the DMU and replaces the output signals of an active extender card. Discrete switch settings simplify testing. The unit is housed in a rugged aluminum case.
-
product
Spectral Light And Color Meter w/ Flicker measurement
BTS256-EF
Spectroradiometer for the illuminance (photopic, scotopic, melanopic), spectrum, light color, color rendering index, and flicker. Cosine field of view illuminance measurement for accurate evaluation of extended illumination. Flicker measurement. Spectral measurement technology, required for LED light, color, color rendering, color effects. Photodiode for synchronization to pulse width modulated light and flicker measurement.
-
product
SMD LED Aging Test Machine
CX-6100
Shenzhen Chuangxin Instruments Co., Ltd.
Designed to measure the aging-life and color comparisons of 50pcs 5050 SMD LED and 100pcs 3528 SMD LED.• 150 separate constant current supply• Aging functions: constant current, impact pulse, on-off mode• Range of forward voltage(VF): 5.0V• Range of forward current(IF):1) constant current: 0-100.0mA2) Impact pulse: 0-200.0mA• Range of impact pulse frequency: 10-9999Hz; Duty ratio: 1%-99%
-
product
P-Series Single Channel Power Meter
N1911A
30 MHz video bandwidth Single shot real time capture at 100 M sample/s per second Key Measurements: - peak, average, peak-to-average ratio, rise time, fall time and pulse width22 Predefined formats: WiMAX, DME, HSDPA, etc. One screen view for pulse measurement analysis: Auto Scale, Auto Gate, Rise/Fall Time, Duty Cycle, etc. Internal Zeroing and Calibration while connecting to the DUT Bench Vue software enabled
-
product
Power Meters and Sensors
Anritsu offers the world's most comprehensive range of power meters. The ML2490A series has the performance required for narrow fast rising-edge pulse power measurements (e.g. radar), while the ML2480B series is suited for Wide-band power measurements on signals such as W-CDMA, WLAN, and WiMAX.The ML2430A series of power meters are designed for CW applications, offering a combination of accuracy, speed and flexibility in a low cost package.
-
product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780179-01
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
product
Synchronous Generator
ZET 7190
The Synchronous generator ZET 7190 is intended for generating sine, pulse, saw-shaped signals. It has 2 synchronous channels and can be used individually, or as a part of control and automation systems.