Filter Results By:
Products
Applications
Manufacturers
Prototyping
Construction of first working designs.
- Pickering Interfaces Inc.
product
PXI Prototyping Module, 1-Slot, 15-Pin D-Type
40-225A-601
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
MIPI Soundwire Total IP Solutions
Soundwire
Soundwire is suited for small, cost-sensitive audio peripherals such as modern digital class-D amplifiers and digital microphones. The Total MIPI SoundWire IP Solution from Arasan enables early adopters the fastest path to adoption of this new standard by offering a comprehensive IP package that includes the Verilog RTL source code for Master and Slave, fully validated for compliance with the standard, a comprehensive test environment with a compliance suite for verification of the IP package, a SoundWire Hardware Development Kit (“HDK”) for FPGA prototyping, a SoundWire protocol analyzer and a complete SoundWire software stack.
-
product
Vehicle Multiprotocol Interface Module
C Series
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
sbRIO-9866, Non-Enclosed, 1-Port C Series LIN Interface Module
785965-01
Non-Enclosed, 1-Port C Series LIN Interface Module—The sbRIO‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The sbRIO‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis. Non-enclosed modules are designed for OEM applications.
-
product
COM Express Type 6 Prototyping Kit Based On Intel® 12th Gen Core™ I5-12600HE
COM Express Type 6 Alder Lake-P
The COM Express Type 6 Alder Lake-P is a powerful COM Express Type 6-based IoT solution development kit powered by Intel 12th Gen i5-12600HE 12-core (4 P-core + 8 E-core) SoC with integrated Intel Iris Xe GPU graphics (80 execution units) and comprehensive high speed interfaces.
-
product
PXI Prototyping Module, 1-Slot no Connector
40-225A-001
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
LIN Interface Device
LIN Interface Devices are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. LIN Interface Devices work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
Prototyping Service
Not sure if your new idea is going to work? Come and talk to us. We have a lot of experience in developing proof-of-concept benchtop systems. Remember, it’s not a “lash-up”, it’s the “first step in your product development cycle”. The picture shows a prototype double-pass spectrometer (on the left) that was built into a portable, robust benchtop unit (on the right).
-
product
PXI, CPCI Development And Prototyping Board
TE2100
Team Solutionsí PXI Development and Prototype board is the fastest road for system integrators to deliver a PXI customized product and provides design engineers with a speedy avenue to release PXI based prototypes and products.
-
product
Custom & OEM Products
Applicos can provide custom hardware and software for many applications within the Analog/Mixed Signal area. We offer a unique combination of full-service assistance throughout the entire product realization process, from conceptualization to prototyping and manufacturing.
-
product
RS LabSite® modulogic
RS LabSite® modulogic is a comprehensive and adaptable software suite conceived for introducing service loads into individual components or complete vehicles, or performing calculations within the framework of Virtual Prototyping (standardized loadsequences, virtual generation of load data). This enables you to stay in full control of all tasks that follow the acquisition of measurement data in the proving ground.
-
product
Support Services
Libra offers our customer a full suite of support services to help manage your product across the entire product life cycle. One of the most important aspects of our partnership with our customers is a robust supply chain management solution. We have spent decades building our partnerships with our valued suppliers, to offer you an extensive supply chain you can rely on. Over the years, Libra has invested heavily in systems and sophisticated data analytics, to intelligently manage that supply chain and link it to you product and schedule requirements. At the front end of your product’s life cycle, we offer rapid prototyping, full NPI support and strong DFx capabilities, to assist in making your product cost effective, quality driven and highly manufacturable. We also offer a full suite of RMA and warranty support services to support your product through its entire life cycle.
-
product
Rapid Prototyping Solution
SFINX
SFINX® is a rapid prototyping solution that enables customers to rapidly test an idea, concept or application, using equipment compatible with rolling stock requirements.
-
product
Flying Probe Tester
Pilot 4D V8
The Pilot 4D V8 represents the latest frontier in flying probe test technology; it is the complete solution for those who want maximum performance: the highest test speed, low to medium volume, test coverage and flexibility, for prototyping, manufacturing, or repairing any type of board. Its vertical architecture is the optimum solution for probing both sides of the UUT simultaneously.
-
product
USRP-2955, 10 MHz to 6 GHz, 80 MHz Bandwidth, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
785264-01
The USRP-2955 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. It is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2955 has the RF and processing performance for applications such as spectrum monitoring, direction finding, signals intelligence, wideband recording, and radar prototyping. The USRP-2955 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
product
400 MHz to 4.4 GHz, Reconfigurable USRP Software Defined Radio Device
783147-01
400 MHz to 4.4 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2942 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
product
SSOP-to-DIP Adaptor
Series 651000
SSOP IC to DIP Adapter. Allows the use of .65mm pitch surface mount ICs in thru-hole designs. Ideal for prototyping and testing/evaluating SSOP ICs. Adapter can be cut to smaller sizes by end user. Consult factory for panelized form or for mounting of consigned ICs.
-
product
PXIe-5775 , 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Digitizer
785592-01
The PXIe-5775 is a PXI FlexRIO Digitizer that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PXIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
product
Vehicle Multiprotocol Interface Device
The Vehicle Multiprotocol Interface Device excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
PXIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Digitizer
785590-01
The PXIe-5775 is a PXI FlexRIO Digitizer that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PXIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
product
NI Embedded Control and Monitoring Software Suite
The NI Embedded Control and Monitoring Software Suite helps you quickly respond to the changing requirements of your system with a single, highly optimized toolchain for every phase of your design cycle, from modeling and simulation to prototyping and validation to deployment and beyond. The suite features LabVIEW and recommended add-ons specifically for building embedded control and monitoring systems.LabVIEW is the ultimate design software to efficiently design, prototype, and deploy applications with hundreds of prevalidated libraries, tight hardware integration, and a variety of programming approaches including graphical development, .m file scripts and integration of C/C++, and Python and HDL code.
-
product
PXI FlexRay Interface Module
PXI FlexRay Interface Modules provide two fully functional FlexRay interfaces, allowing an individual electronic control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. PXI FlexRay Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
Laser Type PM Sensor Evaluation Kit
Panasonic Industrial Devices Sales Company of America
The SN-GCJA5L Laser Type PM Sensor Evaluation Kit provides design in concept prototyping and testing of the Panasonic SN-GCJA5 Laser Type PM Sensor.
-
product
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device
783923-01
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2940 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
product
IR CAMERAS
IRC800
Sierra Olympic Technologies Inc.
The IRC800 Series cameras offer the ultimate in flexibility for research scientists. Camera operators can vary integration times, frame rates and cold filters to meet the most precise testing requirements making the IRC800 the perfect instrument for prototyping system development or where application requirements may change. A 1/3-liter LN2 pour-filled Dewar assembly maintains temperature for up to 20 hours unpowered and 9 hours powered which makes the IRC800 Series perfect for Scientific Imaging, Process Analysis and Quality Assurance. A developer’s kit is available for users who wish to create their own applications.
-
product
PXI Prototyping Module, 2-Slot, 96-Pin Micro-D
40-225A-102
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
Benchtop AOI Machine
Sherlock-300F
Many companies, especially smaller electronics manufacturers, put off adding automated optical inspection (AOI) to their process because of the high capital investment, the sharp learning curve, and the need for an experienced operator to program and fine-tune it. Benchtop Sherlock 300F AOI machine was designed to make in-house AOI affordable and manageable for first-article inspection, prototyping, and even full production inspection requirements. It features the same technology and quality build of the batch and inline Sherlock 300 models—plus the same two full days of installation and training at your facility offered with the other models*—in a smaller size, at a lower price point.
-
product
DIN Eurocard Plugbord
VECTOR Electronics and Technology, Inc.
Boards for 96 and 160-pin DIN Eurocard plug-in application with option to mount DIN 41612 type connectors on ends. Available with different circuit patterns for prototyping applications.
-
product
COM Express Type 6 Prototyping Kit based on Intel® 12th Gen Core™ i5-12600HE
COM Express Type 6 Alder Lake-P
The cExpress-BT is a COM ExpressR COM.0 R2.1 Type 6 module supporting the Intel Atom® processor E3800 Series and Intel® Celeron® N2900/J1900 processor SoC (codename: Bay Trail). The cExpress-BT is specifically designed for customers who need high-level processing and graphics performance with low power consumption in a long product life solution.