Filter Results By:




Showing recent results 256 - 262 of 262 products found.

  • Infrared Thermometer

    DITH 120 - Desco

    Infrared Thermometer is also known as laser thermometerInfrared thermometer is a thermometer which infers temperature from a portion of the thermal radiation sometimes called blackbody radiation emitted by the object being measured.Laser is used to help aim the thermometer or non-contact thermometers or temperature guns, to describe the device's ability to measure temperature from a distance. By knowing the amount of infrared energy emitted by the object and its emissivity, the object's temperature can often be determined. Infrared thermometers are a subset of devices known as "thermal radiation thermometers".The design essentially consists of a lens to focus the infrared thermal radiation on to a detector, which converts the radiant power to an electrical signal that can be displayed in units of temperature after being compensated for ambient temperature. This permits temperature measurement from a distance without contact with the object to be measured. A non-contact infrared thermometer is useful for measuring temperature under circumstances where thermocouples or other probe-type sensors cannot be used or do not produce accurate data for a variety of reasons.

  • Light Analysis

    Thorlabs, Inc.

    Welcome to Thorlabs; below you will find links to detectors and instrumentation that measure the various properties of light, a subset of our entire line of photonics products. Thorlabs offers an extensive selection of instruments that measure the properties of light. Our versatile power and energy meters can be used with over 25 different sensors in order to make NIST-traceable power and energy measurements. If the convenience of a meter is not desired, our selection of detectors includes basic photodiodes (uncalibrated and calibrated), photodetectors (biased, amplified, and avalanche), CCD and CMOS arrays, position detectors, integrating spheres, and photomultiplier tubes. The Beam Characterization category contains beam profilers (camera and scanning slit), a wavefront sensor, spectrometers, and interferometers, while the Polarimetery link leads to a selection of instruments used to measure and control the polarization of light.

  • Infrared Gas Analyzers

    Campbell Scientific, Inc.

    Campbell Scientific offers both open-path and closed-path infrared gas analyzers for measuring carbon dioxide and water vapor. Campbell Scientific also offers a closed-path analyzer for measuring methane, nitrous oxide, or isotopologs of carbon dioxide. Designed specifically for eddy-covariance flux measurements, these analyzers offer the following benefits: integrated system design, aerodynamic intake or analyzer body, low power, synchronized measurements with the sonic anemometer, reduced spatial separation between analyzer and sonic anemometer, unrivaled flexibility in data acquisition, and data collection from additional system sensors with Campbell Scientific dataloggers.

  • Dual ways thermocouple meter

    VA8060 - Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD

    This economical type K & J thermocouple thermometer provides accurate and reliable temperature measurement in an economic and compact design. , high & low temp indicator (audible alarm), interchangeable J & K type thermocouples, stores up to five groups of data, provides & holds T1-T2, average, maximum and minimum, selectable °F & °C temperature units, auto-power off setting, backlight. For even greater accuracy, 8060 features a resolution of 0.1°C/0.1°F (below 1000°C) and 1°C/1°F (above 1000°C). Plus with 2pcs K-type thermocouple sensors It is often necessary to take temperature measurements with different types of thermocouples. 8060 makes it possible without switching meters. These meters are equipped with a button that switches between K-type or J-type thermocouples, giving them the power of 2 meters, all in one unit. The meters are also equipped with a dual-level LCD that shows measured high and low temperatures along with the current reading. To freeze the display for easy recording, simply press the HOLD button. A °C/°F button will toggle between Celsius and Fahrenheit.

  • Solar Tracking and Pyranometers

    Sutron Corporation

    The demand for energy increased rapidly over the past few decades and the trend is not expected to stop in the near future. These made researchers focus on renewable energy sources due to the environmental pollution caused by the existing conventional energy sources. Solar energy is one of the renewable energy that has been under deep research. Unfortunately, the main problem with this solar energy is lack of efficiency. Different positions of the sun throughout the day causing the static photovoltaic modules position inefficient. This paper discusses design of two-axis solar tracking system that considers multiple input parameters such as solar radiation and photovoltaic module output power for more efficient solar tracking algorithm. Some of solar tracking system conducted by other researchers uses various types of sensors including light dependent resistor (LDR) which is not efficient and can be easily affected by external environmental factors. Instead, this paper proposes the usage of pyranometer for measuring solar radiation as one of the input parameters. The solar tracking system controlled by PIC microcontroller that collects multiple input parameters and uses developed algorithm to control stepper motor movement for optimal photovoltaic module positioning. Solar Tracking System Utilizing Pyranometer for Optimal Photovoltaic Module Positioning (PDF Download Available). Available from: [accessed Dec 2, 2015].

  • 2-Channel Front End

    BEQ II.1 - HEAD acoustics GmbH

    *Binaural, digital equalizer with 24 bit technology and USB interface.*The digital equalizer BEQ II.1 combines the characteristics of an equalizer, a two-channel front end and an A/D converter into one mobile and very versatile measurement tool.*Binaural, aurally-accurate recordings can be conducted easily with BEQ II. The AES/EBU interface allows a quick and easy expansion into a four-channel system, e.g. with the HMS III or HMS IV. Via the ADAT interface, up to four BEQ II units can be connected, allowing for eight-channel recordings.*Integrated signal conditioning allows common measurement sensors (Microphone, Line, ICP�) to be directly connected to the front end. In addition, separate pulse inputs are available e.g. for RPM data acquisition.*Thanks to the high-performance built-in battery - external DC power supply is also possible - and its low weight, BEQ II.1 is the ideal tool for either mobile or stationary operation.

  • Fanless Embedded System With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, 4-CH PoE And MXM 3.1 Type A

    eBOX671-521-FL - Axiomtek Co., Ltd.

    The eBOX671-521-FL is a GPU computing embedded system that comes with 4-CH PoE and MXM 3.1 Type A slot for applications in machine vision, edge computing, traffic vision, deep learning, and artificial intelligence of things. The outstanding eBOX671-521-FL with enhanced GPU computing performance is powered by the 9th/8th gen Intel® Core™ i7/i5/i3 processor with up to six-core, Intel® Pentium® processor, or Intel® Celeron® processor and comes with Intel® Q370 or optional Intel® C246 chipset. The fanless embedded GPU-based system is equipped with dual DDR4 ECC/non-ECC SO-DIMM slots for up to 64GB of system memory. The embedded vision system has an optional MXM type A slot for NVIDIA GTX1030 and GTX1050 graphics modules to enhance the performance of the visual display. Furthermore, this Intel® Coffee Lake-based embedded box PC is specially designed with four Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports with a total power budget of 60W, six USB 3.1 ports and two Gigabit LANs to connect different devices or sensors. It comes in great expansion possibilities, including one internal MXM 3.1 type A connector, two full-size PCI Express Mini Card slots and two SIM slots. For storage, it has two swappable SATA HDD drive bays with a height of up to 9.5 mm and one mSATA for RAID 0 and 1 feature. Besides, we have designed a flexible I/O window slot for incorporating application-oriented I/O functions to meet the requirements of various cases. This embedded vision computer can be mounted using wall or DIN-rail mounting for versatile use in various environments.