Showing results: 151 - 165 of 351 items found.
-
mks Ophir
Ophir has a number of ways to measure high laser powers up to 12kW without heavy water cooled equipment. Most of today’s lasers can be set to emit for a short, precisely controlled period of time. If a short exposure to the laser of 0.3 – 10s is sufficient to measure the power then there are compact, uncooled sensors available for this purpose.
-
ZET 412 -
ZETLAB Company
The Signal amplifier ZET 412 with pseudo-galvanic separation is intended for amplification of input signals from various primary transducers and their transmission to the measuring unit (e.g., ZET 210 ADC/DAC unit) as well as for power supply of the connected sensors.
-
N Series -
IDS Imaging Development Systems GmbH
The compact and robust aluminum housing of the camera with lockable GPIO connector for trigger and flash and GigE connector, has two monochrome CMOS sensors and a projector. The projector is available either with blue lights in the visible area or with infrared lights. Via Power over Ethernet a data transfer and power supply are possible with long cable lengths.
-
LadyBug Technologies LLC
In addition to statistical information, pulse profiling sensors provide time domain trace measurements. The sensor measures RF power, converts and sends data points fast enough to build a time domain trace. The measurement can be triggered and the signals detail can be plotted for on-screen viewing as shown above. This was was made with a LadyBug LB480A sensor. Additionally, these sensors can make triggered pulse measurements such as pulse width and pulse repetition time along with all of the measurements made by our peak and pulse sensors. LadyBug's Pulse Profiling Sensors also provides a full complement of statistical information such as CDF, CCDF and PDF.
-
AT-2040 -
Agate Technology
With AT-2040 you will find the features required for your application without having to install cumbersome and expensive addons. AT-2040 features a full-automatic sensitivity test mode, sensor simulation, power supply output for sensors that require voltage such as the 7310 and 991V aviation sensors, a built-in sensor charge amplifier for both single-ended and differential charge accelerometers, and a custom sensor input that can be configured to fit most accelerometers with a one to one cable.
-
BeamTrack -
mks Ophir
Thermal sensors that measure laser power and single shot energy like standard thermal sensors but in addition measure laser beam position and laser size. This position sensing detector measures laser beam position to 0.1mm accuracy and laser size measurement of a Gaussian beam to +/-5% accuracy. Measuring laser position is important for laser alignment where the laser position sensor can provide feedback to the laser position control.
-
imc Test & Measurement GmbH
For measurements on rotating components and moving machinery, imc offers modern telemetry systems for a wide variety of tasks: whether single-channel torque monitoring of a rotating shaft, multi-channel strain gauge and temperature measurements on a train wheel-set or non-contact power measurement on a vehicle drivetrain in harsh environments. There are transmission electronics available for a large variety of sensors, such as strain gauge (quarter-, half- and full-bridge), thermocouples, PT100/1000, as well as IEPE sensors and voltage signals.
-
PDU-200 -
Konrad Technologies GmbH
The PDU-200 is a power distribution unit for automatic tests equipment (ATE). Its outputs are software controlled to allow power on sequencing and direct interaction form the test sequence. The integrated 24V power supply provides power for additional equipment like relays and sensors. The PDU-200 is intended to use with an external remote-control panel which provides On & Off buttons as well as an E-Stop and acknowledge button. It’s integrated eight port switch simplifies wiring as no additional components are required.
-
Rohde & Schwarz GmbH & Co. KG
Our RF & microwave power sensors ensure precise and reliable measurements. They provide the highest measurement accuracy and speed, simple operation, technological leadership in thermal, diode and OTA core measurement elements as well as traceability to national standards.
-
Keysight Technologies
Make accurate and reliable measurements in the 50 to 110 GHz frequency range. Keysight's waveguide power sensors offer best SWR, high reliability and low loss, and come with a 50 MHz calibration port to reduce measurement uncertainties.
-
Ferrites India
The tip of the unit detects the field polarity. The magnet surface is placed parallel to the unit tip. Two 1.5V AA battery operated. Power ON Switch activates the sensors and gives visual indication in form of two LEDs placed on the arm of the unit.
-
772D -
Keysight Technologies
The Keysight 772D is a high-performance, dual-directional coupler designed for broadband swept measurements in the 2 to 18 GHz range. This coupler can be combined with Keysight power sensors and power meters for reflectometer applications. Forward and reverse power measurements on transmitters, components, or other broadband systems are made simpler using the Keysight 772D. The broadband design allows the use of a single test setup and calibration for tests spanning the entire 2 to 18 GHz range.
-
MC142 -
Powertek LLC
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using signals with various crest factors. Frequency modes enable selection of frequency, amplitude and duty cycle of the output signal. These are suitable for basic calibration of digital and analog oscilloscopes along with transient recorders. The calibrator is equipped to measure temperature with TC and RTD temperature sensors. Its built-in multimeter can be used independently or simultaneously with the calibrator output. Testing of transducers of various types, regulators and sensors can be performed, without the necessity to use any other measuring instrument.
-
Mountz Inc.
To improve your product quality and lower your product loss rate, try Mountz torque sensors. Whether you need laboratory-grade precision to measure hand tool output in inch-ounces or the durability to handle frequent pneumatic tool testing in the foot-pound range, Mountz has the right torque sensor for your application. In-line rotary torque sensors even allow you to directly measure the torque a power tool applies to an actual fastener, giving you the most accurate measurement possible. Designed for ease of use, Mountz torque sensors are plug and play, helping technicians get right to work and minimizing the chance of error.
-
SeaGuard -
Aanderaa Data Instruments AS
The SEAGUARD® is the core module used in small and medium sized underwater observatories. Whether used as a multipurpose instrument, or as a hub for strings in the water column, the SeaGuard manages connected sensors and the real-time communication of data and meta-data to shore. In autonomous configurations, long battery life is achieved with aggressive power routines keeping the full system at the lowest power levels possible.