Showing results: 331 - 345 of 362 items found.
-
ST-312V (ST-312mV) -
Standard Electric Works Co., Ltd
● 3 1/2 digit liquid crystal display.● 200mV and 2V full scale input sensitivity.● Single Battery operated 9V supply or ±5V DC power supply (Dual supply).● Built-in low battery indication and automatic polarity indication.● Decimal point selectable.● Low power dissipation Typically less than 20mV.● High input impedance (> 1M ohm).● Guaranteed zero reading for 0 volts input on all scales.● True differential input or single-ended input.● Self mountable with optional mounting bezel.● Low cost high performance.● EN 50081-1 EN 50082-1 EN 55022 EN 61000-4-2 IEC 801-3
-
VOT-52 -
Standard Electric Works Co., Ltd
● Voltage test: 12V to 1000V AC/DC (8 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 120V, 230V, 400V, 750V, 1000V.● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test : LED +/-● Audible continuity test.● Phase rotation test : /● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● ELCB / RCD trip test.● Flashlight function.● Safety standard : IEC/EN 61010-1 III 1000V IEC/EN 61010-1 IV 600V IEC/EN 61243-3 EN 61326-1
-
ST-312A(4~20mA) -
Standard Electric Works Co., Ltd
● 3 1/2 digit liquid crystal display.● 200mV and 2V full scale input sensitivity.● Single Battery operated 9V supply or ±5V DC power supply (Dual supply).● Built-in low battery indication and automatic polarity indication.● Decimal point selectable.● Low power dissipation Typically less than 20mV.● High input impedance (> 1M ohm).● Guaranteed zero reading for 0 volts input on all scales.● True differential input or single-ended input.● Self mountable with optional mounting bezel.● Low cost high performance.● EN 50081-1 EN 50082-1 EN 55022 EN 61000-4-2 IEC 801-3
-
CRY6151B -
CRYSOUND
CRY6151B is a full-featured electroacoustic tester newly launched by CRY Sound. It is powerful and stable. It can measure the performance indicators of headphones (USB, Bluetooth, anti-noise), microphones (electret, MEMS, moving-coil type), headphone and microphone assemblies, receivers/headphone speakers, speakers/loudspeakers (common, Bluetooth), loudspeaker crossover devices, and other electroacoustic devices, such as sensitivity (SPL), impedance, distortion (THD), resonance frequency F0, left and right headphone balance, left and right headphone position, phase polarity, microphone current and voltage, SNR, microphone directivity, speaker's TS parameters, telephone receiving and sending loudness ratings, etc. Its test frequency range can be up to 20 Hz - 20 kHz.
-
56-865 -
CTEK Power USA
US 0.8 is CTEK’s smallest 12 V charger. It offers state of the art technology and is perfect for charging smaller 12 V batteries that can be found in motorcycles, jet skis, ATVs and lawnmowers. It is also suitable for maintenance charging “normal- sized” batteries such as car batteries.The unique display allows the user to follow the entire charging process. The US 0.8 is a compact and fully automatic 6-step charger for 12 V batteries from 1.2–32 Ah and is suitable for maintenance charging up to 100 Ah. The US 0.8 is splash and dust proof, delivers 0.8 A and is designed to protect vehicle electronics. It is non-sparking, reverse polarity protected and shortcircuit proof. The US 0.8 is delivered with 5-year warranty.
-
Alpha Lab, Inc.
The AlphaLab Voltage Touch Monitor enables personnel to identify voltage problems that usually remain hidden. The monitor reads the voltage on a finger (which is identical to the voltage at every other point on the body). It can detect as little as 1/10 volt in two modes: DC and AC/Spikes (ESD transients). In the DC mode, the displayed voltage is either positive or negative, and is usually very low if grounding is being worn and is functioning properly. Higher DC voltages (even while grounded) occur if a DC ionizer is blowing too close or if the person rubs against a high-static material or comes in contact with metal at a DC potential. If personal grounding is not being used, any DC signal can build up over time, and the DC mode continues to show the instantaneous body voltage as it changes. In the AC/Spikes mode, any transient voltage spike at least 1/2 millisecond long is temporarily displayed. If there are several consecutive spikes, only the highest is displayed, regardless of polarity. If the signal is a repetitive (AC) wave, the peak voltage is displayed, but always as a positive number. Even when proper grounding is worn, several tens of volts often occur with transients and AC. Maximum error for DC and AC is only 2% of the reading +/- 0.1 volt.
-
MS111 -
MSG Equipment
The test bench is intended to test AC compressors of wide range of vehicles on R134a refrigerant. The equipment detects failures of a vehicle unit before its mounting in a car, whether it is a remanufactured, repaired unit or a used one. In the process of testing, data is shown on LCD display. It gives an opportunity to follow testing results realtime, save and/or print them due to software special features. Unit fixation mechanism is very flexible: a compressor can be easily fixed, no matter what kind of fittings it has. Units with electromagnetic clutch or electromagnetic valve can be tested both separately and simultaneously. Peculiar features of electric commutation are considered, connection polarity is identified automatically, indicator on the control panel indicates on presence of a diode in a circuit.
-
40-666-011 -
Pickering Interfaces Ltd.
The 40-666 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive. Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the40-666/667 User Manual.
-
40-667-011 -
Pickering Interfaces Ltd.
The 40-667 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.Each multiplexer channel can support 30A of continuous current and switch up to 40V signals. The switches can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the 40-666/667 User Manual.
-
ERAVANT
Full band waveguide detectors are GaAs beam lead Schottky diode-based detectors that are specially designed for millimeterwave network analyzer applications. With a proprietary circuitry design and careful diode selection, these zero-biased detectors exhibit high sensitivity and extremely flat output characteristics. The below standard offering covers the frequency range of 18 to 170 GHz and offers a 1 MHz video bandwidth and 1 MΩ video output impedance. The standard models also have the capacity to handle a maximum RF input power of up to +17 dBm. The RF interface of these detectors is a standard waveguide with an integrated Faraday isolator to improve the port VSWR. The output voltage polarity is negative and the connector type is a female SMA. Other configurations are offered as custom models.
-
DAQ-2500 Series -
ADLINK Technology Inc.
ADLINIK DAQ-2501 and DAQ-2502 are high-speed and high-performance analog output multifunction DAQ cards. The devices are able to update up to 8-CH, 12-bit analog outputs simultaneously at sustaining 1 MS/s. The reference sources and the output polarities are programmable on per channel basis, combining with the multiplying DAC architecture, ADLINK DAQ-2500 series DAQ cards can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees the CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The DAQ-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
CRY6151 -
CRYSOUND
CRY6151 Electroacoustic Analysis System is a full-featured electroacoustic device tester launched by CRY Sound. It has a history of 10 years. It is powerful and stable. It can measure the performance indicators of headphones (USB, Bluetooth, common), microphones (electret, MEMS, moving-coil type), headphone and microphone assemblies, receivers/headphone speakers, speakers/loudspeakers (common, Bluetooth), communication helmets, loudspeaker crossover devices, and other electroacoustic devices, such as sensitivity (SPL), impedance, distortion (THD), resonance frequency F0, left and right headphone balance, left and right headphone position, phase polarity, microphone current and voltage, SNR, microphone directivity, speaker's TS parameters, telephone receiving and sending loudness ratings, etc. Its test frequency range can be up to 20 Hz - 20 kHz.
-
PXI-2500 Series -
ADLINK Technology Inc.
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
PXI-2501 -
ADLINK Technology Inc.
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
PXI-2502 -
ADLINK Technology Inc.
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
