Plugs
A male connector.
-
product
5-Way Multi Charger for PS200 Series
Teledyne Gas & Flame Detection
The 5-Way Charger is specifically designed for use with the PS200 Series portable gas detector.Simply plug it in and charge up to five units simultaneously.
-
product
GPIB Connection Module
DSOX2000-806
DSOX2000-806 GPIB Connection Module plugs into the rear panel expansion slot to provide handshaking and interface communications over an 8-bit data bus.
-
product
Averaging Extensometers for ASTM D5656 Shear Tests
Model 4013
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 4013 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Cable Assembly, Receiver, 36", Mini Coax, 20 SMA Plugs
540129010209
Cable Assembly, Receiver, 36", Mini Coax, 20 SMA Plugs.
-
product
Cable Assembly, Receiver, TriPaddle/Mini Coax, 36", 4 SMA Plugs, And 19 Pin ML HDMI
540364010210
Cable Assembly, Receiver, TriPaddle/Mini Coax, 36", 4 SMA Plugs, And 19 Pin ML HDMI.
-
product
4 & 5 Pin Trailer Circuit Tester
PT7866
Traces each lighting function to the terminal in question. Plugs into the trailer plug. Each LED light corresponds to the circuit being energized. Provides an easy to connect ground terminal for trailer lighting set-up.
-
product
Long Gauge Length Axial Extensometers
Model 3542L
Jinan Testing Equipment IE Corporation
The dual flexure design makes the 3542L very rugged and insensitive to vibrations. These extensometers are designed for testing a wide range of materials including metals, plastics, composites and ceramics. Epsilon’s Model 3543 is recommended for applications requiring long gauge lengths and larger measuring ranges.The Model 3542L comes standard with Epsilon’s quick attach kit, making it easy to mount the extensometer on the test specimen. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The 3542L extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
3 Digit LCD Voltmeter
DPM 400
The DPM 400 is a 3 digit LCD voltmeter with 10mm (0.39") digit height and annunciators. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into a DIL socket or can be panel mounted using the snap-in bezel and window.
-
product
Power Backplanes
3U cPCI
CompactPCI bus is compatible, in terms of electrical specification, with the PC world’s PCI bus. The mechanical specifications were adapted to the commonly used Euro-board plug in systems for 19″ racks.
-
product
AC Current Transducer
iDVM 333
The iDVM 333 AC Current Transducer plugs into the iDVM 510 multimeter and measures current (as AC millivolts) with no need to break the circuit. Special Introductory Price: $52.50FeaturesTransformer jaws that detect AC current flowing through a conductorSelectable sensitivity between 1mV/A and 10mV/AHand Guard to protect your hand for safetyLarge, easy-to-operate trigger opens the transformer jaws
-
product
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 36"
7-245436673-036
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 36"
-
product
Pico Data Logger / Data Acquisition Range
Pico data acquisition products provide a straightforward answer to your data logging needs.Our data loggers require no power supply and simply plug into a USB port on your PC, or an Ethernet port on your PC or network.Every logger is supplied with PicoLog data acquisition software so you can measure, record and analyze your data.
-
product
7 Spade Pin Circuit Tester / Maintenance Kit
#8028
Innovative Products of America
Test, clean and restore 7 spade pin connections.The tester will verify that the tow vehicle is sending proper signal to the connector, while accompanying cleaning tools will remove corrosion, and verify proper pin size on both male and female truck/trailer plugs. For use with 7 spade connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardPatentedKit Includes: #7893: 7 Spade Pin Circuit Tester, #8023: Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
product
Single 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-013
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexers. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
3.5 Digit LED Voltmeter (BLUE)
SP 300-BLUE
The SP 300 is a 3 digit LED voltmeter with 9mm (0.36") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into an 8-way SIL socket and can be fitted into a panel via the fixing clip. Splashproof protection to IP65 is achieved by fitting the seal supplied
-
product
Digital Sensors
PMA-Series
Solar Light’s NIST-Traceable PMA-Series Digital Sensors represent the pinnacle of accuracy, durability, and selection on the market today. Our sensors measure discrete bands of the electromagnetic spectrum from the UVA, UVB, UVA+B, UVC, Visible Light, and Infrared regions. Both narrow and broad bands are available to fit any application, including germicidal requirements, environmental probes, and sensors for biologically weighted spectra (such as the erythema and CIE action spectra.) Over 135 different sensors are available in a variety of packages to fit any environment, from indoor clean rooms to harsh locations outdoors to 100 meters under water. Please note that Solar Light offers both Digital Sensors and Analog Sensors in the PMA-Series lineup. Select these Digital Sensors if you prefer to plug into our PMA-Series Radiometers to read the output of the sensor on the meter’s display. Digital models are typically used as discrete sensors that are portable and located to provide short term information. (By contrast, please select Analog Sensors if you don’t need a digital display output of the reading, if you will be connecting to your own datalogger, or if you plan to use a voltage source to provide excitation voltage to the sensor and a digital volt or amp meter to read and convert the results. Analog Sensors are typically used as process sensors that are permanently installed to provide ongoing information.)
-
product
Moulded On Thermocouples IEC
A moulded plug gives a robust construction as well as providing a waterproof termination.
-
product
Volume Commander
Imagine a device that you can plug into your already existing favorite gear and get multiple new tones out of them without having to change your settings? Pedals, Amplifiers and even your Plugins… The Morley Volume Commander is ready to take your tone possibilities to the next level!
-
product
600-Watt DC/DC Converter, 6U VME
64PS1
The 64PS1 is a 600 Watt DC/DC Converter that plugs into a 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +28 VDC input and provides a single output at 600 Watts continuous or 1,000 Watts peak.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
50Ω UWave SMA 2.92 Cable Assembly, 40GHz, 0.25m
40-977-544-0.25m
50 Ohm uWave SMA 2.92 Plug to uWave SMA 2.92 Plug Cable Assy, 0.25m Long.
-
product
Full Performance and Flexibility on ECIS 8 Well Arrays
Sciospec ECIS Adapter
The ECIS CULTUREWARE 8 well arrays are a very common choice for a broad range of impedance-based cell experiments like cell groth, cell migration, wounding/healing, barrier function, tox-screening, adhesion and proliferation studies. With the Sciospec ECISadapter you can bring your ECIS experiments to the next level: more speed, higher resolution, more possibilities. Harness the full power of Sciospec impedance analyzers on your existing ECIS arrays. The ECISadapter just plugs into compatible Sciospec impedance analyzers like the ISX-3 and you´re good to go.
-
product
PICMG 1.3 Half-Size Single Board Computers
PICMG 1.3 half-size Single Board Computers (SBC) suit multiple single board computer requirements. The slot SBC cards offer high speed and wide bandwidth computing platforms, with plug & play, providing flexibility in various industrial applications.
-
product
Temperature Rise Tester
WS-1
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right. It is designed and manufactured according to IEC884－1, GB2099.1-2008 and other relevant standard of electrical accessories.
-
-
product
PXI 10A Power MUX, 4-Bank, 4-Channel
40-661-101
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
product
Data Logger for Temperature
DSR-T
Original medical probe being resistant to low temperature and free of toxicity and halogen Outstanding measuring resolution even in low temperature Original fittings for sensor connection, ensures 100,000 plugs Support single DSR connecting to PC via USB interface, and multiple DSR grouped in RS485 or LAN networking for central management
-
product
Hybridization Oven
REXMED ROV-201
MOD. ROV-201, AC 110/230V, Plug type: , Hybridization oven, HS CODE: 841780, UNCCS CODE: 484352, UMDNS CODE: 14410, Main construction: powder coated steel and SS304, Controller: Microprocessor based PID controller, water proof keypad with timer, ˚C/PV and ˚C/SV display and setting, Timer: 9999/min, 9999/hr, Timer has DELAY_ON and DELAY_OFF function and at the end of operation audio and visual warning, Working range: Ambient +5˚C~85˚C, Stability at 37˚C: ±0.1˚C, Sensor: PT 100Ω, Temperature audio and visual warning for AL-H and AL-L and OFS correction setting, Heater: 1.2KW, Shaking timer: 999/min, 999/hr, shaking timer can be set in second, minute or hour function and at the end of operation audio and visual warning, Motor: Noiseless powerful brushless induction motor 15W, Rotation: 5~60rpm adjustable, Rotator: for 8pcs(optional), Orbital: 20~250rpm adjustable, Platform: L30 X W20cm, Chamber: L35 X W25 X H42.5cm, Capacity: 37.2L, chamber with glass viewing window, Optional: Rotator for 8pcs X 1set
-
product
Decoder Tester
Electronic Solutions ULM GmbH & Co. KG
Decoder tester for decoders, plug in for NEM652, NEM651, 21MTC, single wire, motor, LED monitor and 20mm speaker. It´s so easy to handle and knows all kind of interfaces.
