Parallel Digital Interfaces
-
product
Ethernet To Parallel Digital Interfaces
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
product
Ethernet To Parallel Digital Interfaces
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
PXI-6529, 48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module
779949-01
48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module—The PXI‑6529 is an industrial, parallel digital input interface. PXI‑6529 devices are ideal for a variety of applications from automotive design, industrial factory automation, and machine control to aerospace, laboratory research, and biomedical applications. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6529 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Wide Band Filters (multi-octave)
MINI-ERF® Series
The MINI-POLE® Extended Range Series of tunable filters was developed to address applications needing a small, surface mount package with wide tunability. This tunability is accomplished by the use of multiple internal tunable filters along with high performance PIN diode RF band select switches all contained in one housing. The tunable filters are designed to minimize size and power consumption while maintaining high RF power handling and linearity characteristics. Parallel or serial digital interface can be selected by a mode pin for ease of integration into your design.
-
product
5.0 MP Custom Lens Camera Module (Monochrome)
e-CAM50_CU9P031_MOD
e-CAM50_CU9P031_MOD is a 5 MP custom lens monochrome camera module based on Aptina's MT9P031 CMOS image sensor with S-mount lens holder attached to it. The MT9P031 is a 1/2.5" Optical Form factor, Electronic Rolling Shutter CMOS sensor. The e-CAM50_CU9P031_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM50_CU9P031_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
product
1.3 MP Custom Lens NIR Camera Module (Monochrome)
e-CAM10_CU0130_MOD
The e-CAM10_CU0130_MOD is a 1.3 MP NIR Camera module (Monochrome) based on the Aptina / ON Semiconductor AR0130CS CMOS image sensor with S-mount lens holder attached to it. The AR0130 is a 1/3” Optical Form factor, Electronic Rolling Shutter CMOS sensor with enhanced sensitivity in the Near Infrared region and superior low light performance. The e-CAM10_CU0130_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM10_CU0130_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
5.0 MP Custom Lens Camera Module (Monochrome)
e-CAM50_CU9P031_MOD
e-CAM50_CU9P031_MOD is a 5 MP custom lens monochrome camera module based on Aptina's MT9P031 CMOS image sensor with S-mount lens holder attached to it. The MT9P031 is a 1/2.5" Optical Form factor, Electronic Rolling Shutter CMOS sensor. The e-CAM50_CU9P031_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM50_CU9P031_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
product
Camera Link Translators
CLT-303
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
-
product
Interface Board for Gigabit Ethernet
40-965-910
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
product
Interface
RPCIE-1553
Abaco Systems RPCIE-1553 is the latest generation of performance and flexibility for MIL-STD-1553 A/B Notice II on a native PCI Express module. Available in -40°C to +70°C temperature with one, two or four dual-redundant channels, the RPCIE-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787457-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
PCIe Host Adapter: Single Port (x8), Gen 3
M9048B
The M9048B is a PCIe host interface card for computers with PCIe expansion slots. It provides a high performance link from an external computer to an AXIe or PXIe Chassis. The card has a Gen 3 x8 PCIe cable link capable of achieving speeds up to 8 GB/s. This means a high performance system can be built using desktop or rack-mounted computers.
-
product
Interface
RCEI-830A-TB
Designed for embedded, laboratory and simulator applications, the RCEI-830A-TB supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, receive message time-tagging and error detection, and IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL).
-
product
Embedded Avionics Interfaces
Versatile interfaces that enable embedded systems and computers to communicate with avionics databus networks.
-
product
Interface
R15-MPCIE
The R15-MPCIE is very small (30mm x 40.95mm x 4.7mm) and lightweight for applications deployed in highly constrained environments where platforms require minimum SWaP solutions. It is designed for those working in avionics test and simulation for field and test support, and for use in data logging in which it offers significant advantages and flexibility.
-
product
Interface
RCNIC-A2PA3
The RCNIC platform is a high performance, 3U CompactPCI module (PMC on carrier card) for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation. An IRIG-B receiver/generator is included for synchronization to an external IRIG-B time source and for synchronization between multiple RCNIC boards.
-
product
High Performance PCIe-GPIB Interface Card
82351B
Convert your PCI computer directly into an intrumentation control; install easily with plug-and-play configuration.
-
product
PXIe Avionics Interface Cards
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
product
I²C/SPI Interface Device
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
product
Vehicle Multiprotocol Interface Module
C Series
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
Scalable RF Interface Unit
1257A
The Astronics 1257A is a sixth-generation RFIU design with four Commercial Off-The-Shelf (COTS) options from 1U to 4U. It comes with a new easy-to-use LXI Core 2011-compliant device and new enhanced features.
-
product
14-Bit Digitizer
PA72D14130
The PA72D14130 is a 14-bit digitizer, capable of capturing waveforms at speeds up to 130Msps. An onboard offset voltage source allows capturing offset signals while still using the optimal range for maximum ADC utilization. Two onboard filters allow suppression of out-of-band noise. The 64MWord onboard memory enables capturing very long waveforms, or sequentially capturing multiple signals with minimal intermediate bus communication.
-
product
Interface Board, Compact, 8:1 Ethernet RJ45
40-965-907
Compact converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
product
PCI Express Host Interface SSD/Drive Decode Support
Teledyne LeCroy provides NVM Express, SATA Express and SCSI Express protocol decoding, analysis and test equipment to SSD storage companies worldwide. It works closely with the following organizations providing equipment to its members and conformance programs.
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 2 DAQ Channels and 2 AWG Channels
DN2.813-02
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
Dual Channel 180 MS/s Digitizer PXI / PXIe Card
GX2482
The GX2482 series are a high performance, dual differential channel, 16-bit digitizer offering high dynamic range and excellent SFDR. The module’s differential inputs, coupled with its low distortion makes it an ideal instrument for analyzing high performance or low level analog signals. Each channel offers 3 selectable low pass filters, a 16 bit, 180 MS/s ADC, and 64 M words of memory for each channel.
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 250 MS/s on 4 Channels Digitizer, 625 GS/s AWG on 4 Channels
DN2.822-04
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
PXI DeviceNet Interface Module
PXI DeviceNet Interface Modules have an onboard microprocessor and optically isolated physical layer to communicate with a DeviceNet network system as a master (scanner) or slave device. The modules ship with a high-level API that provides complete access to a DeviceNet network and features easy access to device data and streamlined explicit messaging. PXI DeviceNet Interface Modules are ideal for prototyping DeviceNet systems, PC-based control, embedded control systems, PC-based human machine interface (HMI), and DeviceNet network management utilities.
