Parallel Digital Interfaces
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 2.5 GS/s on 4 Channels, 1.5 GHz Bandwidth
DN2.222-04
-
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.442-16
-
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXIe 8 Bit High Speed Digitizer - 1.25 GS/s on 4 Channels, 500 MHz Bandwidth
M4X.2212-X4
-
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
AXIe High-Speed Digitizer/DAQ, 8-bit, 1 GS/s, 32-ch
M9709A
-
Based on the AXIe standard the M9709A is an 8-bit digitizer, able to capture signals from DC up to 500 MHz at 1 GS/s with excellent measurement accuracy across 32 synchronous channels within a single card. The digitizer also enables long acquisitions with its very large on-board memory of up to 16 GB.
-
Product
Interface
3508 MMS ECM
-
The 3508 Electrical Conversion Module (ECM) provides six (6) RS-232 outputs and ten (10) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 4 DAQ Channels and 4 AWG Channels
DN2.813-04
-
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PXI H. Density Digital I/O Module 32 Bit O/C
40-410-002
-
The 40-410 range of Digital I/O Modules are suitable for operating external devices, such as heavy duty relays (power, RF and high voltage types), solenoids, lamps, or for interfacing with external logic such as a programmable instrument with a BCD interface. Two choices of output drive are available: TTL for interacting with external logic and Open Collector Transistor for operating external devices with voltages to 50VDC and currents to 500mA.
-
Product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-03
-
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
Interface
RQVME2-1553
-
The RQVME2-1553 provides new levels of performance and flexibility for MIL-STD-1553A and B Notice II on the VMEbus. Available in commercial, industrial and conductively cooled versions with one, two or four dual-redundant channels, the RQVME2-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
USB-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, USB Digital I/O Device
779975-01
-
The USB-6509 is an industrial, bus-powered USB device that can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is … required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the USB-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI IF Digitizer
-
PXI IF Digitizers offer onboard signal processing (OSP), which enables features such as quadrature digital downconversion (DDC), real digital downconversion, and anti-alias filtering. Models include a high dynamic range front end and a highthroughput PXI Express interface, which allows them to stream IF data to disk for hours at the full sample rate. You can also choose a PXI IF Digitizer that can convert IF signals to I/Q data, so you can use this model as a standalone IF digitizer or as part of a Vector Signal Analyzer.
-
Product
ARINC 429 Bus Interfaces
-
AIM’s > ARINC 429 test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O.
-
Product
PXIe 16 Bit High Speed Digitizer - 250 MS/s on 2 Channels
M4X.4420-X4
-
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.442-08
-
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
USB-C Thunderbolt™ 3 Appliance with Two Independent, Dual Redundant 1553 Busses, Eight ARINC-429/717 Channels, 4 RX/TX & 4 RX
TBOLT-MA4
-
Full Featured and Native 1553 and ARINC Thunderbolt interface! Full PCI Express interface – same advanced interface as PCIe backplane cards in a small, portable, rugged appliance.
-
Product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
-
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
Product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
-
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
Product
PCIe-4065, PCI Express, 6½-Digit, ±300 V Digital Multimeter Device
779771-01
-
The PCIe‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
PCI-8532, 1-Port, DeviceNet Interface Device
781062-01
-
The PCI‑8532 is a high-speed DeviceNet Interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the controller area network (CAN) physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. The DeviceNet specifications are managed by OVDA, Inc. You can program the PCI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.
-
Product
PXI-8431, 4-Port, RS485/RS422 PXI Serial Interface Module
778985-01
-
4-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/4 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785648-02
-
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
PMC Interface Card
CPCIC-MA4
-
The CPCIC3/6-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
Product
2-CH PCI ExpressR IEEE 1394b Frame Grabber
PCIe-FIW62
-
The PCIe-FIW62 is an IEEE 1394b (FireWire 800) interface card which provides two high-speed FireWire 800 ports with data transfer rates up to 800 Mb/s on a PCI ExpressR x1 lane. The PCIe-FIW62 provides two direct-connect IEEE 1394b bilingual connectors with a screw-lock mechanism. These screw-lock connectors provide a reliable connection between the PCIe-FIW62 and up to two IEEE 1394b cameras. A 4-pin ATX power connector on the PCIe-FIW62 supports IEEE 1394b cameras that draw power directly from the frame grabber. Each port has a green LED on the front panel that will illuminate when the PCIe-FIW62 is connected to a IEEE 1394b camera for convenient identification of channel connection status.
-
Product
PXIe-8430, 8-Port, RS232 PXI Serial Interface Module
781472-01
-
8-Port, RS232 PXI Serial Interface Module—The PXIe‑8430/8 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Combo Unit, 7.5 Digit Digital Multimeter (DMM) with 10-Bit 1GHz Digitizer in a Single VXI Slot
6084A
-
Increases test system performance and density with this combo unit, which packages a 7.5 digit Digital Multimeter (DMM) together with a 10-bit, 1 GHz Digitizer into a single VXI slot.Replaces the Wavetek 1362 DMM, Analogic DBS Series, and Agilent VXI DigitizersDigitizer with 4 Inputs, 10-bits, 1 GHz, up to 4 GS/s and Ranges up to 500V DMM with 7.5 Digits for DC Volts, Current and Ohms with AC Volts up to 1 MHzIVI-COM Drivers and Soft Front Panels ProvidedMore Dynamic Range (by 20 dB for DMM and 12 dB for Digitizer) for Better Legacy Range Mapping
-
Product
PXIe-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
787358-01
-
PXIe, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module - The PXIe-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each line for input or output and you also can configure each line with a user-configurable pull-up or pull-down resistor. Using the PXIe-6509 programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. The PXIe-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. The PXIe-6509 provides programmable input filters for eliminating glitches or spikes and for debouncing digital switches or relays through a software-selectable digital filter.
-
Product
PXI Interface Module, AIT ARINC 429
M3407A
-
Interface to the LRU in avionics test solution 4, 8, 16, or 32 software programmable Tx/Rx channels with full error injection/detection Programmable high/low speed operation Real-time recording and post analysis of multiple channels Concurrent operation of all Tx/Rx channels PXI triggers, star trigger, and PXI 10 MHz clock
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785958-01
-
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Digital/Pattern/PE Card
PE32H
-
The PE32H represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE32, the PE32H offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PE32H also supports deep pattern memory by offering 32M of on-board vector memory with dynamic per pin direction control and with test rates up to 66 MHz. With new 32M log memory, PE32H can capture 32 channels data or fail log.
-
Product
Interface Panel for SLSC
THROUGHPOINT™
-
Bloomy's ThroughPoint™ Interface Panel provides a simple, yet highly-flexible connection between the unit under test and resources in a National Instruments Switch/Load/Signal Conditioning (SLSC)-based test system.
