Showing results: 106 - 120 of 200 items found.
-
Analog Devices Inc.
Analog Devices TimerBlox parts are small, accurate, and simple timing devices designed for six basic operations: voltage controlled oscillation (VCO), low frequency clocking, pulse-width modulation (PWM), one-shot generation and signal delay, and power-on reset (POR). TimerBlox devices combine an accurate programmable oscillator with precision circuitry and logic. No capacitors, no crystals, no microcontroller, and no programming are required. A 20 mA source and sink capability enables the devices to directly drive opto-isolators and transformers for electrical isolation. An ideal solution for space-limited applications, each TimerBlox device can be placed at the point of use.
-
ESCP-BMS1 Sensor -
ES Systems
ESCP-BMS1 is an absolute, gauge or differential pressure sensor of ultra-high resolution with analog (0-3,3V), PWM, SPI or I2C interface. The output is fully calibrated, and temperature compensated based on the internal temperature sensor and the factory calibration coefficients which are stored in the embedded memory. The sensor is ready to be installed directly to the end system without further processing with medical, HVAC, industrial, commercial & automotive applications. The total error including repeatability, hysteresis, non-linearity, thermal offset and calibration error between 0°C and 60°C is better than 0.25% FS.
-
Ducommun Inc
Ducommun millimeter wave products include various passive components including multi-hole directional couplers (PCM), crossguide couplers (PCC), magic tees (PCT), coax power dividers (PPD), bandpass, low pass and high pass filters (PFB, PFL and PFH), waveguide diplexers (PDC), waveguide transitions (PRC and PTW), waveguide to coax adapters (PTC) and waveguide components (PWS, PWE, PWH, PWM and PWT). These passive components cover frequency range from 8.2 to 110 GHz and feature high performance and low cost.
-
AMP-204C/AMP-208C -
ADLINK Technology Inc.
ADLINK"s new AMP-204C/AMP-208C DSP-based 4/8-axis advanced pulse-train motion controllers incorporate up-to-date floating-point DSP and FPGA technology, enabling high pulse output and encoder input frequency up to 6.5 MHz and 20 MHz respectively. Leveraging ADLINK" s Softmotion technology, the AMP-204C/AMP-208C offer impressive comprehensive and application-oriented motion functionality to reduce development time while maintaining superior throughput and accuracy. Superior synchronous motion control performance combines with point-table function integrating multi-dimensional interpolation, such as 3D linear/circular/spiral interpolation with enhanced trajectory and velocity planning, for contouring applications in semiconductor, display and conventional manufacturing industries. The AMP-204C/AMP-208C also support PWM control with three different control modes for frequency or duty cycle, benefiting laser engraving/marking/cutting applications. Moreover, hardware-based position comparison and trigger output are applicable in AOI applications.
-
RogaDAQ16 -
ROGA-Instruments
With the introduction of the RogaDAQ16 USB 2.0 data acquisition system, a new age of measurement technology begins.*USB 2.0 / 480MBIT (USB1.1/12MBIT COMPATIBLE)*16 analog input channels (16bit/500kHz max.)*ICP ® ( IEPE ) sensor supply (24V/4mA)*0.125V to 10V input range*Individual preamplifiers*4 analog output channels (16bit/100kHz)*Powerful DSP (255MIPS) for filtering, control etc.*24 digital I/Os*Optional 24bit counter, timer, PWM, incremental encoder*Free drivers for major application software*including DASYLab; LabView & DiaDem drivers & RogaRec Software
-
1U647-001 -
Sigma Tek, Inc.
The 1U647-001 is a low cost calibration standard used to determine if a 1U632-100 or a 1U663-100 DMU requires factory calibration. Its portability makes it ideal for field-testing. The standard generates signals that simulate the aircraft’s resolvers, rotary variable transformers (RVTs), and linear variable displacement transformers (LVDTs). The unit also generates a pulse width modulated (PWM) signal, and routes the output of an ARINC 429 source to the different DMU input channels. The calibration standard connects directly to the DMU and replaces the output signals of an active extender card. Discrete switch settings simplify testing. The unit is housed in a rugged aluminum case.
-
781056-01 -
NI
The PXIe‑6363 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6363 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
779370-01 -
NI
The PCI‑7813 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7813 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
779363-01 -
NI
The PCI‑7811 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7811 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
782255-01 -
NI
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
782254-01 -
NI
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
782256-01 -
NI
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
781442-01 -
NI
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
ams AG
The magnetic rotary position sensor product family detects the absolute angular orientation of an on-axis two-pole magnet rotating over the center of the IC. The absolute angular position can be provided in various formats, including PWM, ABI and UVW, or directly read through the host interface. According to the application’s requirements, resolutions from 8-bit up to 14-bit are available. This technology can be employed in high-accuracy angle position detection, high-speed rotation systems and brushless DC motor control. Any rotary magnetic position sensor can replace either absolute or incremental optical sensors, other magnetic and inductive technologies, potentiometers or magnetic switches.
-
MS013 COM -
MSG Equipment
Tester for diagnostics of voltage regulators. The device simulates control signals for a tested voltage regulator. It contains integrated physical and program interfaces of all actually existing control modes of modern alternators. Adapter is controlled by clock encoder with button to install and change parameters. Installation and parameter data appear on LCD display. The handset tester possesses the opportunity to change existing and implement new functions and interfaces in the software. Update download is carried out through USB port. Built-in power supply gives an opportunity to use the device as high-precision ohmmeter or generation of arbitrary PWM signals. Diagnostics lasts about 2 minutes.
