Showing results: 826 - 840 of 1811 items found.
-
MX Series -
Aim-TTi
Three or four high performance outputs each with full functionalityRange switching gives variable voltage/current combinationsShared power mode provides double power from a single outputLow output noise and ripple via linear final regulationHigh setting resolution of up to 1mV and 0.1mAVariable OVP and OCP trips on all outputs50 setting memories per output plus 50 linked memoriesSelectable voltage tracking (isolated tracking)Selectable current meter averagingSwitchable remote sense capabilityGraphic LCD provides simultaneous output meteringNumeric or spin-wheel control of all parametersIndividual or combined output on/off control with programmable delay sequencing.3U half-rack case for bench or rack mounting (4U rack kit accessory available)RS-232, USB and LAN (LXI) interfaces (P models)GPIB option (P models only)Duplicate power & sense terminals at rear (P models)
-
QL Series II -
Aim-TTi
Advanced dc power supplies, single or triple outputUp to 112 watts per outputVery high precision, very low noise, excellent dynamicsAdvanced user interface with numeric and rotary controlMultiple voltage/current ranges for increased flexibilityMultiple non-volatile memories for power supply set-upsSwitchable remote sense provides perfect load regulationComprehensive protection including OVP and OCP tripsCompact bench footprint; modular width for rack mountingAuxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)Bus programmable via USB, RS232, GPIB or LAN (P models)LAN interface is LXI compliantDuplicate power and sense terminals at rear (P models)
-
TSX Series -
Aim-TTi
Compact & lightweight power supply0 to 18V at 0 to 20A or 0 to 35V at 0 to 10ABench or rack mounting, front & rear terminalsSilent fan-less convection coolingVery low noise, excellent transient responseComprehensive protection including OVP tripHigh setting resolution, remote sense terminalsAnalogue controls
-
R4K-80 Series -
MATSUSADA Precision Inc.
R4K-80 series is higher performance and next generation model of existing RK-80 series DC variable power supply, which has been receiving good reputation for its innovative compact size and variable range feature. 4-digit meter and high resolution D/A, A/D converters are added newly for more precise setting and reading. Needless to say, the innovative compact size, variable range feature and high operability are remaining same as conventional RK-80. R4K-80 series is the best suitable DC power supply for a variety of applications from laboratory experiment to line productions.
-
FS725 -
Stanford Research Systems, Inc.
The FS725 integrates a rubidium oscillator (SRS model PRS10), a low-noise AC power supply, and distribution amplifiers in a compact, half-width 2U chassis.
-
Kuhne electronic GmbH
Bias Tee for remote power supply of preamplifiers and converters via the coaxial cable.
-
Fairview Microwave Inc.
Fairview’s bi-directional amplifier models are designed for use in both commercial and military applications and will support any signal type and modulation format such as 3G and 4G telecom, WLAN, OFDM, DVB and CW/AM/FM. Fairview’s bi-directional amplifiers offer high power density, efficiency and linearity in small lightweight environmentally sealed packages with SMA connectors. These units also feature a quick-connect circular locking connector for DC and control functions and each design uses a single voltage supply with voltage regulation.
-
KP Series -
MATSUSADA Precision Inc.
KP series is the sophisticated bidirectional power supply device with the regeneration capability*, optimal for evaluating not only in-car inverters for hybrid and electric vehicles but motors, generators, high-capacity vehicle batteries and capacitors as well as wind or solar power generation. We make available the extensive lineup ranging from 2kW to 120kW so you can choose the optimal model according to various applications including development and production.
-
LD-LBOD-A10 -
Labodam
BOD MeterLD-LBOD-A10is a benchtop unit designed to automatically measure B.O.D. (biological oxygen demand) with 0 to 4000 mg/ L measurement range. Simple and safe mercury pressure difference measurement method is applied to prevent poisoning caused by the leakage of the mercury column. Equipped with high end brand mini thermal printer, quickly prints measurement process data, result data. Automatically saves test data on power failure and executes experimental process once power supply is on.
-
Fiberinthebox
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
Meco Instruments Pvt. Ltd.,
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
72-6694 CAL -
Tenma
The 72-6694 CAL from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
72-6694 CAL D -
Tenma
The 72-6694 CAL D from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
72-6694 CAL DU -
Tenma
The 72-6694 CAL DU from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
Auto -
CanDo
The CANdo AUTO Module is a rugged, multi-purpose CAN bus module with a USB port, two precision analogue inputs & a DC power supply input. The module is capable of operating either connected to a PC, or in a standalone mode powered from a 12 or 24V DC supply, such as a vehicle battery. The module maybe used as an interface between a PC & a CAN bus, or between analogue sensors & a CAN bus, in standalone mode. In addition, the module maybe programmed to transmit fixed, periodic CAN messages automatically on power up.