Showing results: 1756 - 1770 of 1812 items found.
-
ST-312A(4~20mA) -
Standard Electric Works Co., Ltd
● 3 1/2 digit liquid crystal display.● 200mV and 2V full scale input sensitivity.● Single Battery operated 9V supply or ±5V DC power supply (Dual supply).● Built-in low battery indication and automatic polarity indication.● Decimal point selectable.● Low power dissipation Typically less than 20mV.● High input impedance (> 1M ohm).● Guaranteed zero reading for 0 volts input on all scales.● True differential input or single-ended input.● Self mountable with optional mounting bezel.● Low cost high performance.● EN 50081-1 EN 50082-1 EN 55022 EN 61000-4-2 IEC 801-3
-
Scientech Technologies Pvt. Ltd.
Power Supply is the most indispensable component of any electronic laboratory. A reliable, most accurate, fully specified, guaranteed and an efficient Power Supply Equipment are thus manufactured on a large scale by Scientech Technologies which has robust output protection and fault detection capabilities. DC Power Supplies with Different specifications of Voltage and Current are being manufactured for various Applications. The DC power supply converts the conventional 110 V or 220 V alternating voltage into continuous pulsating DC voltage (+3.3 V, +5 V, +12 V and -12V) used by various electronic components. A DC Power Supply also regulates the voltage to eliminate spikes and surges common in most electrical systems.
-
FADOS9F1 -
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
-
MIC-3042 -
Advantech Co. Ltd.
The MIC-3042 is a 4U enclosure designed for standard cPCI power supplies. It is equipped with a cPCI 500 W redundant 2 1 power supply with hot-swap support. The system has 8 slots for CompactPCI boards and 6 slots for IEEE 1101.11 rear I/O transition boards. The MIC-3042 comes with a built-in high quality backplane that supports 64-bit / 66 MHz PCI cards.
-
MIC-3890 -
Advantech Co. Ltd.
There are two SKUs for your application: one is a 250W with M12 connector and another is a 250W with Wago connector as input interface. Both can accept 66-160VDC as input voltage via a connector in front panel. The power supply output payload power is +12 V, the +5Vsb voltage is for wake-up events.
-
Advantech Co. Ltd.
MicroATX motherboard chassis offers flexible power supply and satisfied the need for mini industrial chassis with MicroATX motherboards. The IPC chassis offers embedded chassis to meet your need for cost-effective solution.
-
MIC-3022 -
Advantech Co. Ltd.
MIC-3022 is a 4U enclosure designed to host up to 8 CompactPCI 3U cards connected via a 32bit 33MHz or 66MHz PCI bus or serial bus. The chassis can be powered by PICMG2.11 CPCI power supplies or an ATX 400W power supply for cost sensitive applications. A CPCI power supply supports a wide range of applications in the industrial market requiring a robust, compact and reliable platform. Rear transition modules can be installed for each of the 8 slots to support I/O extension. The MIC-3022 enclosure is available for two kinds of backplanes; Legacy backplane provides up to 8 peripheral PCI slot while the hybrid backplane offers three PCI slots and four serial slots. Being a hybrid system, it offers an uncomplicated and cost effective migration solution from parallel 3U CompactPCI® to serial CompactPCI® via the CompactPCI PlusIO standard instead of a bridge or an active logic. To save peripheral slots, there are two SATA connectors reserved on hybrid backplane by cable connection for storage extension. The chassis can be powered by PICMG2.11 CPCI power supplies or an ATX 400W power supply for cost sensitive applications. Four high performance fans provide adequate air flow to all slots, enabling system configurations which can be used in extended temperature environments. With the support of front swappable power supplies and add-in cards as well as a simplified fan replacement mechanism built in, systems based on the MIC-3022 can support a MTTR of 5 minutes or less.
-
N5772A -
Keysight Technologies
The N5772A single output, 1560 W system power supply provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current. It delivers reliable performance and enhanced capabilities in a compact 1U package.
-
N6954A -
Keysight Technologies
The N6954A is designed for automated test equipment (ATE) applications where high performance is critical.
-
N7974A -
Keysight Technologies
The N7974A is designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
N6972A -
Keysight Technologies
The N6972A is designed for automated test equipment (ATE) applications where high performance is critical.
-
N6974A -
Keysight Technologies
The N6974A is designed for automated test equipment (ATE) applications where high performance is critical.
-
N6973A -
Keysight Technologies
The N6973A is designed for automated test equipment (ATE) applications where high performance is critical.
-
US Technologies, Inc.
Full ATE Test Capability. Go/No go testing-power supply batch testing. Complete technical and customer support. End of Life Manufacturing specialists. Complete Testing/Repair
-
N7976A -
Keysight Technologies
The N7976A is designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.