Showing results: 211 - 225 of 1811 items found.
-
Analog Devices Inc.
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
YAVTB000 -
6TL Engineering
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
Blackhawk
Need a replacement part, cable assembly, power supply? Blackhawk stocks the part and accessories you need for development with our line of JTAG Emulators.
-
LEC-Starterkit 2.0 -
ADLINK Technology Inc.
The LEC-Starterkit 2.0 consists of a SMARC 2.0 compliant LEC-BASE 2.0 carrier board, data media, an AC/DC adapter, power cords and is suitable for LEC-AL, LEC-BT, LEC-BTS or LEC-BW modules.
-
-
LS 150 Xenon Arc Lamp Source -
ABET Technologies Inc.
Model LS-150 is a Patented US Pat. No. 8116017 low cost, high output 150 watt Xe arc lamp based light source. The entire source, power supply, lamp, and optical compartment are housed in an extremely compact enclosure, 9 x 6 x 11 inches. The unit's base allows mounting on inch or metric spaced optical tables with the optics centered over the hole pattern to allow for easy integration with the rest of your setup.
-
SparkFun Electronics
The LilyPad Simple Power is a simple e-textile board with a 500mA charge rate that lets you connect and charge a lipo battery and switch it on or off, that's it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no trouble in added a bit of power to your next wearable circuit.
-
Series MPS -
Kepco, Inc.
Series MPSThe MPS is a 70 Watt, triple output MIL-STD-461 compliant power supply specifically designed to meet the needs of IC/microprocessor experimenters. It is actually two linear (series pass) power supplies in one.The first has a single 0-6V, 0-5A output backed up by an adjustable current limiter and overvoltage crowbar for digital work. The second has two tracked outputs, 0 to +20V and 0 to -20V, both rated at 0-1 Amp. The two power supplies are completely isolated from each other, sharing only the front panel meters and the chassis.
-
-
MCH Instruments Co.,Ltd.
Features:• High stability• Overall output protection• Voltage and current continuously variable within nominal value• Voltage and current output preset• CC/CV auto switching
-
PeakTech Prüf- und Messtechnik GmbH
Is a component that provides power to an electrical device. The simplest design of power supply is the linear power supply, which uses a transformer and a rectifier to convert voltage from a wall outlet into the type of power the device needs.
-
Series BHK-MG -
Kepco, Inc.
Kepco's BHK-MG are high voltage, linear, voltage-current stabilizers with rectangular (automatic crossover) output characteristic and ultra low noise and ultra low ripple at the output. All models are MIL-STD-461 compliant. They are offered in two sizes: a 40 watt half-rack design and a 200 watt full-rack power supply. The four models in each size have outputs of 0-300 volts, 0-500 volts, 0-1000 volts and 0-2000 volts. Both digital and analog programming control is featured.
-
NTN -
FuG Elektronik GmbH
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
Renesas Electronics Corp.
Renesas' low cost linear regulators generate a low voltage bias supply from intermediate distributed voltages commonly used in telecom and datacom applications. These devices may be used as start-up or as continuous low power regulators.
-
YAV90075 -
6TL Engineering
This module is ideal to cover power supply needs in fixture proyects. For voltages up to 20V, through two regulable channels. With an minimum input level of 2.7V and a maximum of 20V, has only 340mV of drop voltage. The maximum current supplied for each channel is 1.5A.