-
product
192 X 1 Or 96 X 2 cPCI Low Thermal Relay Scanner Module
DP-cPCI-4032
DP-cPCI-4032, is a hot swappable high density 192x1 or 96x2 relay scanner module. DP-cPCI-4032 is implemented as a 6U cPCI module.The 96 channel scanner is divided into six banks of 16x2 scanner. The banks are isolated from each other using tree switches. Six tree switches are used, one tree switch for each bank. A common tree switch is used to group all the six banks. Depending on the application requirement, it can be configured as 96 x 2 or 192 x 1 scanner. For short circuit protection, resistors are provided for all the common terminals.
-
product
3-Port PCI Express
PEX 8613
The ExpressLane™ PEX 8613 device offers 12 PCI Express Gen 2 (5.0 GT/s) lanes, with support for 3 ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 12-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including workstations, communications, storage, and embedded systems as well as intelligent I/O modules and add-in cards.
-
product
Automatic Calibration Module
ACM2509
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM n...show more -
product
RFFE Protocol Analyzer and Exerciser
PGY-RFFE-EX-PD
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
product
PXI 8 Slot BRIC Module, 1 Resource Distributor, 2 Bus Matrix Inputs
40-569B-112
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-112 is a 8 slot module fitted with 2 Bus Matrix Inputs cards and 1 Resource Distributor card.
-
product
4-Channel 1.25 GHz, 16-bit D/A with Virtex-6 FPGA - 3U VPX
Model 52670
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multimodule synchronization- User-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, ...show more -
product
PXI Multiplexer Single 16 CH 4 Pole
40-630-022-16/4
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole and 1-pole screened.
-
product
QorIQ P204x Processor AMC
AMC711
The AMC711 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P2040 or P2041. The module follows the AMC.1 and AMC.2 specifications. The PCIe interface is configurable as Host or Agent mode and it interfaces as dual x4 (ports 4-7 and 8-11). The P2041 has option to have ports 8-11 as XAUI (10GbE). The AMC711 has up to 8GBytes of DDR-III memory with ECC.
-
product
SMARC Short Size Module with Rockchip PX30 Quad-Core ARM Cortex A35
LEC-PX30
LEC-PX30 based on power-efficient quad-core Arm® Cortex®-A35 SoC is a low-power, low-cost, entry-level, small-sized SMARC rev 2.0 module. For applications, such as IoT controllers, IoT gateways, wearable and mobile industrial devices, basic HMI, sensor concentrators, requiring good computing performance at low power consumption (1.5W- 5W) and Linux Yocto capability, LEC-PX30 is an ideal solution.
-
product
4 Serial Communication Channels, Multi-Mode Programmable, Non-Isolated
SC7
Module SC7 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications. SC7 is the same as SC1 except SC7 reallocates the pins used for CTS Flow Control as four (4) additional system grounds.
-
product
PXI High Voltage Power Multiplexer, Octal 3:1 (SP3T)
40-331A-005
The 40-331A-005 octal 3:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
product
Power Modules
VPC offers a wide array of modules with a variety of connection options that are configurable for virtually any interconnect requirement.
-
product
AT-1120, 14-Bit, 2 GS/s, 2-Channel Signal Generator Adapter Module for FlexRIO
782248-01
The AT-1120 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs. The AT-1120 is ideal for generating complex signals like digital modulations and RF stimuli for functional and performance tests. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the AT-1120, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
product
Wiring Diagnostic System
TRACER 1.0
TRACER creates vehicle- and fault-specific diagrams on the fly. It can diagnose the probable cause of failure in a network of wiring harnesses and modules and lets technicians choose a CAD view of the wiring layout to find the precise failure location (down to a specific pin), so they can correct the issue efficiently. Tracer saves labor costs, overhead costs and helps avoid collateral damage. TRACER streamlines ELT and dealership repair. It's helpful for all vehicles, particularly new models, w...show more -
product
ECAT MiniModules
ECAT STGMM 6
Precise and synchronous acquisition of mechanical strain directly at the strain gauge points of application: This is what the EtherCAT®-based measurement module ECAT STGMM 6 with six time-synchronous strain gauge inputs for quarter-, half- and full bridges has been designed for
-
product
500 Pin SEARAY Cables - Connector to Connector For Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 500-pin SEARAY (250-port) connector.
-
product
PXI 4 Slot BRIC 138x8 1-Pole Dual Analog Bus (3 sub-cards)
40-560A-021-138X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Power Sensors
RTP5540
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 40 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microw...show more -
product
sbRIO-9265, Non-Enclosed, 4-Channel C Series Current Output Module
780921-01
Non-Enclosed, 4-Channel C Series Current Output Module - The sbRIO‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The sbRIO‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity. Non-enclosed modules are designed for OEM applications.
-
product
Constantan, Type T (°C) Contact
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-054
The 40-297A-054 (PXI) and the 42-297A-054 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 22.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
CMX RF Port Extender
CMX-Z25
Complex devices under test (DUT) come with additional antenna ports to support low, mid and high bands - and advanced MIMO schemes such as 4x4 MIMO. The R&S®CMX-Z25 is the solution: Up to 16 DUT ports can be supported with just 4 ports from R&S®CMX500. So even prototypes of 5G smartphones, tablets, laptops or industrial modules with an extended number of antenna ports can now be connected to a single R&S®CMX500. Together with the scalable CMX architecture any 5G and 5G Advanced mobile device can now be tested in one go - without recabling or 3GPP band combo limitations.
-
product
COM Express Type 10 Mini Module With Intel® Pentium® & Celeron® N3000 Series Processors
CEM300
The CEM300, a COM Express® Type 10 module, supports Intel® Pentium® N3710 and Celeron® N3160/N3060 quad-core/dual-core processors (codename: Braswell) with support for 4 GB DDR3L memory onboard. Integrated with Intel® Gen 8 graphics, the COM Express® Type 10 computer-on-module provides excellent graphic performance including support for DirectX 11.1, OpenGL 4.2, and 3D features and resolution up to 4K (3840 x 2160 @ 30 Hz). The ultra-small mini module comes with 4 to 6 watts low power consumptio...show more -
product
PXI 8x SPST High Voltage Reed Relays
40-310-001
The 40-310/320 range of high voltage switching modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
COM Express Type 6 Prototyping Kit based on Intel® 12th Gen Core™ i5-12600HE
COM Express Type 6 Alder Lake-P
The cExpress-BT is a COM ExpressR COM.0 R2.1 Type 6 module supporting the Intel Atom® processor E3800 Series and Intel® Celeron® N2900/J1900 processor SoC (codename: Bay Trail). The cExpress-BT is specifically designed for customers who need high-level processing and graphics performance with low power consumption in a long product life solution.
-
product
Pneumatic Module, ITA, 5 Position (3/8" Flow)
510108144
The 5 Position Pneumatic Modules are made of G10 Epoxy Glass, withstanding temperatures of 140°C. Nomenclature is silk-screened white onto the Modules.
-
product
75 Ohm MCX To MCX Cable Assembly
40-977-761-0.25m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Isolation Amplifier
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics...show more -
product
PXIe-4463, 51.2 kS/s, 2-Output PXI Sound and Vibration Module
783086-01
The PXIe‑4463 offers high dynamic range and THD+N for audio, acoustic, and vibration applications. It provides the high precision and dynamic range necessary for the most stringent audio generation requirements in a modular form … factor. The PXIe‑4463 contains two 24-bit digital‑to‑analog converters to allow for fully differential simultaneous generation. Complete with three gain ranges, the PXIe‑4463 can generate current with programmable, per channel output configurations. The two timing engines allow you to perform multisample-rate applications on a single module and independently start and stop channels on a single module.
-
product
QorIQ P40x0 Processor AMC, PCIe Gen 2
AMC718
The AMC718 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P4040 and P4080. The module follows the AMC.1 and AMC.2 specifications. The PCIe interface is configurable as Host or Agent mode and it interfaces as x8 or dual x4. The module has option for up to 16GBytes of DDR3 memory with ECC.
