-
product
PXI Single SP4T Multiplexer 6GHz 50 SMA
40-784A-101
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
product
Internal DAQ Cards
PCIe, PCI, PC/104, CAN
PC data acquisition cards are particularly suitable for stationary measurement applications. Outstanding in this category are the PCI(e) multi-function cards PCI-BASEII and PCIe-BASE on which you can plug different measurement and control modules to optimize the price-performance ratio.
-
product
ADAQ Data Systems
Atec’s Data Acquisition and Control System (ADAQ™) is a modern, full-featured, highly integrated hardware and software solution that is applicable for use with most commercial and military turbine engine test cell applications. Built upon National Instruments’ respected LabVIEW platform, ADAQ™ is robust, versatile, user friendly, and specifically designed to handle the demanding requirements of engine testing. It links seamlessly to digital engine modules (FADECs, DEECs, EECs, ECUs) as well as ...show more -
product
ARINC825 (CAN Bus) Test & Simulation Module for CPCI With 2 Or 4 CAN Bus Nodes
ACC825-3U-x
ARINC825 (CAN bus) Test & Simulation module for CPCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACC825-3U-x CPCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
NI-9218, 51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module
783367-01
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber, LC Connectors
42-852A-418-M62.5
The 40/42-852A-418-M62.5 is a PXI/PXIe 8-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
16 Differential I/O Multi-Mode Transceiver Channels
DF1
Function module DF1 multi-mode transceivers with 16 programmable I/O channels. Differential transceivers increase resistance to noise by creating two complementary signals. These complementary signals produced on balanced lines double noise immunity by creating lower power requirements due to lower supply voltages.
-
product
SHC68-C68-D4, Shielded Single-Ended Cable, Low Leakage, 1m
152870-01
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
product
PXI/PXIe Very High Density Multiplexer, 10-Channel, 16-Pole
40-675B-002-10/16
The 40-675B-002-10/16 (PXI) and the 42-675B-002-10/16 (PXIe) are 10-channel, 16-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
product
Connect PT100/PT1000 Sensors To Output A Voltage Signal
K- PT100/1000
Our K-PT module is designed to connect up to PT100/PT1000 sensors and simply provides an output voltage signal. Thus enabling the most standard voltage measurement devices to work with PT100/PT1000 sensors. The PT100 sensors offer excellent accuracy and repeatability.
-
product
SH68-68-D1, Shielded Cable, 1 m
183432-01
68-Pin, Female D-SUB to 68-Pin, Female D-SUB, Twisted Pair, Shielded Digital Cable - The SH68-68-D1 Digital Cable connects NI 6533/4 digital instruments and NI 660x or 661x counter/timer modules to 68-pin accessories. This shielded cable features twisted pairing and is offered in different lengths.
-
product
PXI Very High Density MUX 10 Chan 16 Pole
40-675-002-10/16
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
Cryogenic Temperature Modules
Transmit temperature data over long distances to data acquisition locations in research and industrial settings.
-
product
Block Downconverter
RQ028
Teledyne Defence & Space (TDS) down converters are designed to convert digitised, band limited RF signal down to a lower frequency signal. These modules are used to reduce input signal which allows lower speed processors to better process fast incoming signals. A wideband mmW block downconverter suitable for extending the operational bandwidth of other devices into this range. With LO signals at 32GHz and 44GHz, two operational bands are available. Other frequency plans with and without pre-selection can be offered on request.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-155
The 40-297A-155 (PXI) and the 42-297A-155 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 43.8 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
LoRa 1W Breakout
915M30S
Do you need power? This breakout for the 915M30S module from EBYTE is a 1W (30dBm) LoRa transceiver. LoRa is great for long range (miles), low power (in sleep), and low data rates (~500bps). This breakout board is designed to connect to any platform that has SPI and 6 available GPIO. We include a robust edge mount RP-SMA connector to connect large LoRa (915MHz) antennas. In addition, the on-board U.FL connector can be used if you need to get outside a metal enclosure.
-
product
Dynamically Controlled, High Speed Digital I/O PXI Express Card
GX5292e
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
PXI 20 Banks 0f 4 Channel 1 Pole MUX
40-615-021-20/4/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Configurable Relay Matrix Module
DP-cPCI-4341
DP-cPCI-4341 is a Hot-Swappable Configurable Relay Matrix Module. The relays can be operated separately or all at once. The Form A relays can be used to switch voltage signals upto 200V DC. The inputs and outputs are brought out to the fascia for high flexibility. Use of rugged connectors for field terminations ensures long-term reliability. Applications of the module include automatic test equipment, continuity testing, audio telephone line switching and data acquisition system.
-
product
PXI BRIC8 FIBO Matrix Dual 124x4 2pin brkout
40-592A-114
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Open Pluggable Specification (OPS) Digital Signage Player With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q170 And Intel® AMT 11.0
OPS500-501
The OPS500-501 is a 4K resolution OPS compliant digital signage player supporting Intel® Active Management Technology (AMT) 11.0 for better remote management. The space-saving OPS signage module is powered by the 6th generation Intel® Core™ processor with Intel® Q170 chipset. It has one 260-pin DDR4-2133 SO-DIMM socket with up to 16GB memory capacity. Compliant with the Intel® OPS architecture, the 4K-ready signage player provides a high level of compatibility as well as simplified installation,...show more -
product
PXI-2566, 16-Channel, 2 A, SPDT PXI Relay Module
778572-66
16-Channel, 2 A, SPDT PXI Relay Module—The PXI‑2566 is a general-purpose switch module that features independent single‑pole double‑throw (SPDT) Form C armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2566 is ideal for switching, routing, and controlling high-current signals. Each relay channel has a normally closed (NC), normally open (NO), and common (COM) terminal.
-
product
PXI Multiplexer Dual 32 Ch 1 Pole
40-630-022-D/32/1
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole, 4-pole and 1-pole screened.
-
product
Configurable CAN FD Module With A Focus On Analog I/Os
PCAN MicroMod FD Analog 1
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The motherboard PCAN-MicroMod FD Analog 1 focuses on analog inputs and outputs, which are provided with the appropriate protective circuit.
-
product
PXI Very High Density Versatile 2-Pole MUX
40-613-002
The 40-613 Very High Density Versatile 2-pole Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves.
-
product
CompactPCI Chassis for 6U
Advantech 6U CompactPCI chassis are 4U enclosures hosting up to 8 slots, hot-swappable CPCI redundant power supplies, and hot-swappable fan modules.
-
product
PXI 1 Bank of 160 Channel 1 Pole MUX
40-615-022-1/160/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Enhanced 16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT5
The DT5 module (the enhanced version) features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection. Additional features of the DT5 (Enhanced Version) are listed below.
-
product
Near-Field Detection Module for Spectroscopy
nanoFTIR
Reflective AFM-tip illuminationDetection optimized for high-performance near-field spectroscopyPatented background-free detection technologyBased on optimized Fourier-Transform spectrometerUp to 3 spectra per secondStandard spectral resolution: 6.4/cmUpgrade to 3 cm-1 spectral resolution availableSuited for visible & infrared detection (0.5 20 m)Exchangeable beam-splitter mount includedNEW: Suited for IR synchrotron sources
-
product
PCI Express 64 bit Card
EXC-4000PCIe-64/xx
The EXC-4000PCIe-64/xx card for the PCI Express bus (64-bit) supports an Ethernet channel using the M4KETH module. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
