Showing recent results 3556 - 3570 of 4299 products found.
-
DX-30SST - Dexing Magnet Tech. Co., Ltd
DX-30SST Silicon Steel Sheet Iron Loss Meter adopts SCM technique and analog electronics technique, the magnetic circuit of permeameter adopts low loss silicon steel iron core, it is a small tester for measuring the characteristics of silicon steel sheet, met the requirements of tracing the brand of silicon steel sheet.
-
TN 100 - Thermo Scientific
The microprocessor-based waterproof TN100 meter is an easy-to-use turbidimeter that meets the rigor of rugged field applications. It is a "must -have" for anyone monitoring turbidity on the go. Using an Infrared light source, it delivers laboratory accuracy with a resolution of 0.01 NTU across an extended range of up to 20 NTU (Nephelometric Turbidity Units).
-
UI-FT43 - Unuo Instruments
Leather Thickness Gauge is used to measure the thickness of leather. Place the sample in a thickness meter under a specified load for a certain time and them read the thickness. Unuo Instruments supply film thickness gauge, film thickness gauge, rubber thickness gauge and etc. Shore Durometer for rubber is also available.
-
DC502 - Lisun Electronics Inc.
DC502 is CONSTANT CURRENT DC POWER SUPPLY for standard lamp. Function and technical indexes are as follows: • output voltage 4 grades: 6V/12V/24V/50V • output current: DC 0~2.5A (adjustable) • Output current drift at full scale: ±0.05% reading value/10 mins • Monitor range of ampere meter: 0.0000A ~1.9500A, 1.950 A ~2.500A • Accuracy of ampere meter: ± (0.08% reading value + 0.02% full scale) • Max output power: 80W • Continuous working time: 8 hours • Work environment: Temperature 0℃ -25℃, humidity ≤ 85%R.H, supply source: AC220 ±10%, 50/60HZ • Holding conditions: -20~50℃ humidity < 75%R.H • Outside dimension (W×H×D): 333mm×114mm×307mm • Weight: about 8kg • Power: about 1000VA
-
GM2 - Alpha Lab, Inc.
The Model GM2 Measures the strength and polarity of magnetic field up to 30kG when using a standard probes, or 800 gauss (resolution 0.01 gauss) if an HS probe is used. Functions include DC, AC and peak hold along with a user-adjustable alarm which has three modes of operation. DC background field can be subtracted out either by pressing "Relative Zero" or by manually adjusting the offset. The meter includes battery, AC adapter analog output jack and calibration certificate. If a standard probe is used, resolution is 0.1 gauss up to 19,999.9 gauss, which is stronger than the field of any permanent magnet. This 5 digit display allows measurement of tiny difference in strong fields. Above 20kG the meter autoranges to a 30kG range.
-
466 - Red Phase Instruments Australia Pty Ltd.
For field testing or workshop testing the Model 466 is an excellent current source to test meters. It has 4 current ranges, 1A, 5A, 20A and 100A which can be connected to the meter under test from 100A rated sockets on the front panel. Heavy duty silicone test leads having matching plugs are supplied with the 466.
-
ROSS ENGINEERING CORPORATION
Most Ross Meters are supplied as systems consisting of one of the basic meters matched to the VMP series voltage probes or VM series voltage dividers. The VMP series hand held probes extend the voltage measuring capabilities safely to 400,000 volts. The base mounted VD series dividers can extend capabilities, safely, to as high as 1,000,000 volts.
-
IBL-307 - International Biological Laboratories
This Digital Clamp On Power Meter Model 307 can be used to measure True Power, Apparent Power and Power Factor in single phase circuits. It measures AC/DC Current and incorporates a frequency counter. It is autoranging type Digtal Clamp On Power Meter and has 3-3/4 Digits 4000 Counts with 40 segment analog bargraph LCD Display.
-
Bee Instruments
These types of devices are going to be able to measure the flow rate, often for a fluid. These sensors are usually a part of a flow meter, which will be able to record the flow rate. Today, many different types of flow sensors are available. It is possible to find air flow sensors as well, which can sense and determine the velocity of air movement.
-
TLVM - TOEI INDUSTRY CO, LTD.
This equipment measures quantitatively magnetostriction to indicate mechanical striction in magnetizing direction caused when magnetic steel sheet sample was alternately magnetized and is used for research and development of magnetic steel sheet. Magnetostriction is detected as speed signal through the parameters of magnetic flux density and compressive stress with laser doppler vibration meter.
-
CNG-DX - Hollis Electronics Company LLC
CNG-DX provides improved noise generation with its internal digital power meter and built-in noise generator. This single instrument provides accurate and repetitive carrier-to-noise setting ability in one box. The CNG-DX is an ideal instrument for creating realistic scenarios for closed loop testing of satellites, ground equipment and mobile transceivers.
-
TA-500 - Tech-Aid Products
This panel was designed to test primarily the NSD360 series of HSI systems. Panel allows running the complete system on the bench. Included is a panel mounted TA-902 API which can also be used for testing external instruments via a panel mounted switch. The API and standard meter drives allow testing many different instruments.
-
TW3109 - Techwin(China) Industry Co., Ltd
can provide 1 to 4 output wavelengths to meet specific requirements, including the 650nm red source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer needs. Together with the TW3208 optical power meter, it is a perfect solution for the fiber optic network characterization.
-
MD257 - Matco Tools
*Provides readings for volts, amps and ohms required for automotive electrical system tests as well as diode and continuity tests*Lo-Z ghost voltage buster drains ghost voltages leaving only hard signals on meter readings*Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
-
Xtium2 CLHS FX8 LC - Teledyne DALSA
The Xtium2-CLHS FX8 LC supports up to two bidirectional SPF+ modules running at 10Gbit/s. Using CLHS X-Protocol, the Xtium2-CLHS FX8 delivers up to 2.0 GB/s of image acquisition and 6.8 GB/s to host memory. The low-cost SPF+ module and fiber optic cables help extend cable lengths to 100 meters.
