-
product
MEGMET 5000
PU 296
The instrument PU 296 is intended for measurements of voltages, insulation resistances and determination of coefficients PI, DD and DAR at revisions of the high-current equipment. It complies with requirements of the standard ČSN EN 61557-2.
-
product
Water Fluoride Analysis
Aztec AFM631
The Aztec 600 fluoride analyzer provides reliable and highly accurate measurement of fluoride concentrations to enable precise control of water fluoridation.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Coordinate Measuring Machines And Services
TARUS began building CMM with TARUS developed software and proprietary graphical user interface in 1982. TARUS CMM have always been known for ease of use. A TARUS CMM control with TARUS CMM software is available in our new TARUS Easy DMIS 2 software package.
-
product
Field Bag
1048
TESCO has recently updated the Field Bag. The newer Field Bag is slightly smaller than the previous version. The bag features a large main compartment with a removable divider, and two smaller side pockets. The Field Bag comes with a shoulder strap, for ease of mobility. The Field Bag measures 16″ x 8.75″ x 7.5″ (L x H x D).
-
product
LDV System
PS-TM-1D-532
The PowerSight-based LDV System uses the latest solid-state laser technology to give you the powerful and compact laser module for LDV measurements. In addition to its power, the selected laser provides the excellent beam quality pertinent to the accuracy of LDV measurements.
-
product
4½ Digit Multimeter
Model DMM5041
- Economic and full functions- True 4½ digits with 19999 count- Measures DCV, ACV, DCA, ACA, resistance, capacitance, frequency and temperature- Tests diode and continuity- Built-in math operations- Standard interface of USB device
-
product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables
ELCOLEVEL - Software For 3D-straightness Measurement
Optik Elektronik Gerätetechnik GmbH
ELCOLEVEL is a software with interfaces to electronic autocollimators and inclination levels of different manufactureres. This allows for example the 3D-Straightness measurement (twist-, roll- and yaw-angle) of slides in one and the same measuring procedure.
-
product
Precision Current Preamplifier
SIM918
Stanford Research Systems, Inc.
The SIM918 Current Preamplifier is ideal in applications in which the input offset voltage must be kept to a minimum. The DC voltage difference between the two inputs (current input and voltage bias) is accurately measured every 2 seconds, and is nulled.
-
product
Radio Test Set
CMA180
With its frequency range from 100 kHz to 3 GHz, the R&S®CMA180 is ideal for testing all common analog and digital radio systems. Input levels up to 150 W are no problem for the R&S®CMA180. The flexible internal switching capabilities for the audio and RF paths make the R&S®CMA180 suitable for a wide range of test requirements. Users can configure the internal generators, external audio sources, filters and measurements according to the given application. In the predefined test scenarios for receiver, transmitter and duplex tests, the RF and audio paths are preconfigured. This saves time and eliminates configuration errors for standard test cases.
-
product
PXA Signal Analyzer, Multi-touch, 3 Hz to 50 GHz
N9030B
Accelerate innovation in demanding applications with measurement options that range from excellent to exceptionalExtend frequency up to 110 GHz with Keysight smart mixersCapture transient or intermittent signals with real-time spectrum analysisSimplify application-specific testing with X-Series appsPerform deeper troubleshooting with the 89600 VSA software
-
product
Sound Monitoring & Matching API based on Sound Similarity Measurement (for Sound Recognition Projects)
Sound recognition is one of the main application areas of artificial intelligence. Various sound recognition techniques exist and can be used for recognizing speeches, music, environmental sounds, animal sounds, air-borne or structure-borne machine sounds, etc. These techniques contain in common signal pre-processing, feature extraction and feature matching / classification algorithms from a general perspective. However, they differ in implementation in different applications. For example, there are a few good automatic speech recognition software products and APIs, however, they just cannot be used directly in animal sound classifications.
-
product
Doides
Skyworks diode product offering includes PIN, limiter, Schottky, and varactor diodes for a wide variety of microwave applications including WLAN, infrastructure, handset, Satcom, automotive, military, aerospace and defense, test & measurement, metering, medical and RDID.
-
-
product
ScopeCorder
ScopeCorder product family provides flexible and high-performance multi-channel test instruments by combining the benefits of a mixed signal oscilloscope and traditional data acquisition recorder. The ScopeCorder delivers high signal fidelity and long term recording for both high speed transients and low speed trends to meet the most stringent measurement requirements.
-
product
Standard Class AAA Solar Simulator
TriSOL TSS
Essential for testing virtually any material or product that is exposed to sunlight for long or short periods of time, OAI’s low-cost, Standard Solar Simulators deliver highly collimated, uniform light. Depending on configuration, output on these Solar Simulators is rated at 350W -5,000W.These Class AAA Solar Simulators feature OAI’s Advanced Uniform Beam Optics and are available with a choice of air mass filters to reproduce a wide range of solar spectra. For added flexibility, OAI’s proven lens and collimating mirror technology allows for a variety of exposure area sizes. A Class AAA Solar Simulator is an essential tool for manufacturing as well as R&D; it is indispensable in test labs, industry, and in universities. OAI Standard Solar Simulators are used in photobiology, biomedical, solar cell testing, cosmetic testing, and paints & coatings analysis. Based on 35+ years of proven UV light technology, OAI Solar Simulator Systems deliver repeatable, reliable, constant output, and measurement uniformity.
-
-
product
Mixed Signal Oscilloscope: 70 MHz, 4 Analog Plus 8 Digital Channels
MSOX2004A
70 MHz4 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
product
Socket Tester with RCD Tripping
Shanghai Beha Electronics Co., Ltd.
*Mains wiring polarity check.*ELCB/RCD testing.*Measuring ear for line current.*Measuring ear for leakage current.*Helps calculate insulation resistance.*Helps calculate power consumption.*Helps fault finding of standing earth fault.*Fused main adapter.*Appliance testing (with the ad of a clamp meter).
-
product
Flexible Rope-Type Current Probe
RCT1A and RCT5A
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
product
Thermocouple Vacuum Gauge Tubes
DV-6 Series for Medium Vacuum
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.The Teledyne Hastings’ DV-6 series thermocouple vacuum gauge tube acts as a localized sensor which is then paired with a selection of meters or controllers to provide reliable, cost-effective measurements in diverse applications. The robust sensor gauge tube is easily installed into vacuum systems and when properly excited, generates a thermoelectric voltage to provide a vacuum pressure measurement based on gas density. The DV-6 thermocouple vacuum gauge tube fully compensates for temperature and rate of temperature change.Thermocouple gauge tubes are calibrated on vacuum systems that contain N2 or Air, but can be used with other gases. Additionally, thermocouple gauges and their controllers can be recalibrated when a replacement thermocouple gauge tube is installed, following instructions in the manual. However, our DB-20 reference tube is available to confirm meter/controller performance. A complete line of installation accessories are also available to simplify the integration of our thermocouple gauge tubes into a variety of vacuum systems. Our goal is to provide “one less thing to worry about”, when performance matters! With a wide range of meter, fitting, relay and output options, the DV-6 series provides a reliable pressure measurement in numerous industries and applications.
-
product
Optical Power Meter
PM-202B
The all-in-one PM Series Optical Power Meter are designed for use with an Optical Source for performing optical loss measurements on fiber optic cables. The PM-202 series are designed for affordable budgest, but meet the basic demands for real world testing. With a smaller size and weight, it’s easy to take these units into any enviroment.
-
product
Digital Clamp Tester (CE)
M-2100
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Conform to IEC safety requirements.
-
product
Measuring Wheels
Our measuring wheels are the professional's choice for reliability and robust construction.
-
product
SF6 Gas Recovery Device
Weshine Electric Manufacturing Co., Ltd
SF6 gas recovery device is used for the manufacture and use of SF6 gas insulated electrical equipment and the recovery of SF6 gasin scientific research departments. It also has the ability to purify SF6 gas, vacuum and charge.It can vacuum SF6 electrical switch and measure the vacuum degree.It can fill SF6 gas into SF6 electrical switches.It can recover the gas of SF6 electrical switch.It can purify the recovered SF6 gas.Store SF6 gas.
-
product
Two-Pole Voltage Tester According to DIN EN 61243-3 (VDE 0682-401)
PeakTech Prüf- und Messtechnik GmbH
Two-pole voltage testers, are ideal for quick and uncomplicated voltage measurements.
-
product
Compact EMC Test Chamber
EMC-3C
This compact 3 meter test range will settle into test areas of limited space while continuing to produce exceptional performance for EMC measurement. Emission quiet zones of up to 1.5m are accommodated with very repeatable results. Suitable for EMC pre-compliance emissions and compliant immunity testing.
-
product
Voltmeter According to DIN EN 61010-1 (VDE 0411-1)
PeakTech Prüf- und Messtechnik GmbH
An innovative graphic multimeter with a 50,000-digit color TFT display for precise measurements with a high DC basic accuracy of 0.05%. The internal data logger enables the recording of measured values, which can be recorded over a period of several hours and the transfer to a Windows PC at a later time is ensured. Internally stored measured value recordings can also be accessed and graphically displayed on the multimeter itself or on the PC. Via Bluetooth, the measured values can also be displayed live via app for Android and iOS devices, recorded in a table and e.g. send by email for further processing. This multimeter has a variety of measurement functions for direct and alternating voltage measurements (incl.ACV + DCV), direct and alternating current measurements, resistance, capacitance, frequency or temperature, whereby alternating voltage and alternating current are recorded as True RMS values. Due to the extensive measurement functions and the intuitive operation, this device is ideally suited for every electronics engineer, technician and engineer who attach great importance to a precise, indestructible and technically powerful multimeter.
-
product
Glass Thickness Meters
Shenzhen Linshang Technology Co., Ltd.
As a supplier of laser glass thickness gauge and glass thickness measuring tool, Linshang provides two models of glass thickness gauge that can be used to measure the thickness of various glasses, i.e: single-layer glass, double glazing, triple glazing, multilayer glass, LOW-E glass, and insulating glass, especially suitable for installed glass, such as doors and windows, curtain wall glass, etc.. It can measure the glass thickness as well as the thickness of air space (between the glass). The glass check works on the basis of reflection in the glass.
-
product
Meter with 3m Cable 4-Cell Electrode
CyberScan COND 600
Measure from pure water to seawater with one meter! COND600 features a broad conductivity range with Auto-ranging Capabilities for more convenience.
