-
product
RF & Microwave Broadband Amplifiers
SHF Communication Technologies AG
SHF has been active in the design and production of broadband RF-microwave amplifier. The outstanding performance makes our amplifiers suitable for a wide variety of applications in R&D. This includes not only optical communications, but also satellite communications, high-speed pulse experiments, data transmission, quantum communication, radar and antenna measurements.
-
-
product
Mixed Signal Oscilloscope - 6 GHz, 2 Analog and 16 Digital Channels
MSOX6002A
1 GHz - 6 GHz2 analog plus 16 digital channels Easily view and isolate signals on the 12.1-in capacitive multi-touch screen with Zone triggering and 450,000 wfms/s update rate Make more precise measurements with 115 Vrms noise floor at 1 mV/div (1 GHz)Get performance measurements anywhere with the portable 6-in deep size Quickly see analysis details with standard histogram and color grade View signal integrity with jitter and eye diagram analysis options
-
product
CEMS
FMD 09
IMR Environmental Equipment, Inc.
The continuous measurement of velocity and temperature of gas flows is much important at operation of a system with flowing gases (e.g. hall outlet air, exhaust etc.).
-
product
Measurement Devices
In addition to the critical role data loggers play in a data-acquisition system, there are other types of measurement devices. Some measurement devices are used to increase the number of terminals that data loggers can use, which enables them to measure more sensors or control more external devices.
-
product
Expansion Peripherals
Expansion peripherals are used with data loggers to achieve many purposes, including the following: add additional channels, extend data communications networks, perform media conversions, read vibrating wire sensors, and build distributed measurement networks.
-
product
High Speed Digital Contacts
VPC has revolutionized the world of test & measurement with its line of VTAC high speed digital products. With data transfer rates more than 12.5 Gbps per differential pair, the sky's the limit.
-
product
Known impedance for use in loudspeaker measurements
Impedance Box
An impedance box is necessary for measuring the impedance of a loudspeaker. Listen Inc.’s impedance box contains a 0.25Ω resistance. This value is suitable for most loudspeakers, but may be easily swapped out for a different value by the user if speakers with a particularly high or low impedance are being tested. It is available with either XLR or 1/4″ balanced connectors. Please specify type of connectors when ordering.
-
product
Coordinate Measuring Machines
CMM
Aberlink offers a wide range of bridge and hexapod CMMs to suit all applications and budgets, enabling the precise measurement of the smallest of components to parts of over 3 metres long and up to 6 tonnes in weight with a wide range of touch-trigger probes and non-contact measurement options. The comprehensive range of CMMs includes 32 standard sizes of both CNC and manual variants. All CMMs are supplied as a complete turnkey package including the Aberlink 3D measurement software, the easiest to use and most intuitive CMM software currently available.
-
product
Building Moisture Meters
PeakTech Prüf- und Messtechnik GmbH
This material moisture meter enables a user-friendly, fast and non-destructive moisture measurement on all types of building materials, wood and the walls and ceilings of buildings. The absolute humidity as well as the minimum and maximum measured humidity are shown in the large, illuminated digital display.
-
product
Current Transformers
Rishabh Instruments Pvt. Ltd.,
Rish Nano CT is a very reliable, efficient and robust current transformer for measurement of AC current. It provides 100 mA AC output. It can be used in Circuit breakers. Earth Leakage Protection.
-
product
Instrument Grade Data Sensor
WISER 8000
TECAT Performance Systems, LLC
The TECAT WISER Model 8000 dual strain measurement and monitoring system is a wireless data acquisition system for measuring two external strain channels at high data rates up to 8kHz. The small, light, power-efficient, and non-invasive design enables strain measurements in a wide range of applications. With dual external sensor inputs two Micro-Measurements strain gauge bridges can be measured by a single system, for example to measure both thrust and torque loads simultaneously.The Model 8000 ...show more -
product
Primary Current Injection Test Set
T 3000
T 3000 is a primary current injection testing system designed to perform primary tests requested in substations commissioning. It allows to perform different tests and measurements on current transformers, voltage transformers, power transformers, protection relays, energy meters and transducers
-
product
Test & Calibration
Gamma Scientific is ISO/IEC 17025 accredited by NVLAP (NVLAP lab code 200823-0). In addition to assurance of measurement accuracy, accreditation ensures traceability to known standards, provides international acceptance of measured values, and is important for compliance purposes for your own ISO/IEC certifications. Our state-of-the-art, ISO 17025 accredited calibration laboratories in San Diego, California offer a range of test and calibration services including:
-
product
KRYPTON
KRYPTON - Rugged IP67 EtherCAT DAQ ModulesRugged and distributed EtherCAT data acquisition system for field measurement in extreme and harsh environments. KRYPTON DAQ systems offer IP67 degree of protection and can operate in the extreme temperature range from -40 to +85°C and offer high shock protection.
-
product
24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator
DP-cPCI-5004
DP-cPCI-5004, Isolated Pulse Simulator / Counter / Totalizer module is an integrated module for pulse output, pulse measurement and event counting. The module has 16 isolated channels of pulse output at desired frequency. The 16 channels are divided into three groups . The first two groups have four differential and one single ended channels each.
-
product
Ambient Light Sensors
The Ambient Light Sensor (ALS) products from ams provide measurements of ambient light intensity which match the human eye’s response to light under a variety of lighting conditions. Each device has a specific operating range of performance, from very low light up to bright sunlight. High sensitivity coupled with wide dynamic range make these ALS products ideal for operation behind dark inked glass. They enable consumer electronics device manufacturers to implement display dimming and brightness control functions, helping to reduce power consumption and extend battery run-time.
-
product
In-Line Wafer Surface Defect Inspection
ALTO-SD-150/200
ALTO-SD SERIES IS AN IN-LINE INSPECTION SYSTEM SUPPLYING HIGH THROUGHPUT, FULL SURFACE DEFECT INSPECTION FOR ALL KINDS OF WAFERS INCLUDING SILICON, QUARTZ, SAPPHIRE, COMPOUND AND MEMS WAFERS. HIGH-RESOLUTION CAMERA OPTICS PLUS LED ILLUMINATION GUARANTEE RELIABLE DETECTION OF ALL LOCAL DEFECTS. IT INSPECTS DEFECT SIZE OF 1~ 10 MICRONS, CONFIGURABLE INSPECTION RESOLUTION TO OPTIMIZE DEFECT SIZE VS. THROUGHPUT. THE SYSTEM COMBINES HIGH-PRECISION MEASUREMENT, POWERFUL DATA ANALYSIS AND USER-FRIENDLY OPERATIONS.
-
product
Miniature, Battery Powered, Stand Alone Pressure and Temperature Data Logger
PRTemp101A
The PRTemp101 is a miniature, battery powered, stand alone pressure and temperature data logger. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 8,191 measurements per channel. The storage medium is non-volatile solid state memory, providing maximum data security even if the battery becomes discharged.
-
product
Phasor Meter
633
Red Phase Instruments Australia Pty Ltd.
This instrument is designed to demonstrate the properties of phasors and real/imaginary number notation for electrical engineering students. This instrument gives the phase displacement and magnitude of the parameter under investigation. The unit has filters to eliminate harmonic distortion affecting phase angle measurement.
-
product
DC Power Analyzer, Modular, 600 W, 4 Slots
N6705C
The N6705C DC Power Analyzer provides unrivaled productivity gains for sourcing and measuring DC voltage and current into the DUT by integrating up to 4 advanced power supplies with DMM, Scope, Arb, and Data Logger features. The N6705C eliminates the need to gather multiple pieces of equipment and create complex test setups including transducers (such as current probes and shunts) to measure current into your DUT. The DC Power Analyzer also eliminates the need to develop and debug programs to co...show more -
product
Speed Sensors
We manufacture standard and custom speed sensors for various industries including turbo speed sensors. The JAQUET brand of speed sensors specializes in speed measurement by providing sensors and complete systems solutions for applications in demanding and harsh conditions. JAQUET speed sensors can be delivered in flexible quantities, from over a million to hundreds. These mostly customer specific solutions based on solid technology platforms add value through being matched to individual applications.
-
product
Real Time Power Sensors
Providing the highest video bandwidth and fastest rise times, RTP5000 peak power sensors with Boonton’s Real-Time Power ProcessingTM deliver 100,000 measurements per second, no gaps in signal acquisition and zero measurement latency.
-
product
Powered NIM Crates
NIM "Nuclear Instrument Module" is the oldest and simplest nuclear electronics standard. Created in 1969 with AEC report TID20893 (Dec 1969), it defines a powered bin and plug in modules. NIM is the perfect standard for small and flexible setups for high resolution measurements with analogue electronics (amplifier, high resolution analog to digital converter, timing electronics as well as for low / high voltage supplies.
-
product
Test Fixtures
Pneumatically actuated Kelvin connection to custom manufactured device inserts either to complement ART's wide range of precision parametric test equipment or for use with third party measurement hardware.
-
product
Multiport Electronic Calibration Module (ECal), DC To 9 GHz, 6-ports
N7562A
A series of multiport ECal that cascade-able up to 36-ports which makes it possible to calibrate a wide frequency range from DC up to 9 GHz without making numerous connections during calibration process. Ideal for multiport measurement application with VNA in such as high-volume PA/FEM, massive MIMO antenna or high-speed digital interconnect test applications
-
product
Near Field Probes
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
product
Offline Programming, Advanced Simulation & Digital Twin
Silma
Improve your 3D measurement experience with a winning combination: Silma, for advanced simulation and digital twin of your 3D measurement process, and Metrolog for on-machine execution and analysis.
-
product
3U Intel® Core™ i7-7820EQ Quad-Core Processor-Based PXI Express Gen3 Controller
PXIe-3987
The ADLINK PXIe-3987 PXI Express embedded controller, based on the 7th gen Intel® Core™ i7 processor, is specifically designed for hybrid PXI Express-based testing systems, delivering maximum computing power for a wide variety of testing and measurement applications.
-
product
Manual Four Point Probe Sheet Resistance/resistivity Measurement
RT70V series
• Combinational measurement system by Measurement tester(RT-70V) & Stage.• Thickness input with easy JOG dial operation (RT-70V Tester)• Tester self-test function/Auto change-over measurement range function• Thickness & Temperature correction function for Silicon sample
