- Halls Instrumentation.
product
Light Testers
Hall’s have designed and manufactured products for oil, industrial, farming, commercial, and transportation markets. Products such as truck and trailer light testers, bop savers, early engine warning systems, oil spinners, engine control panels, dashes for service rigs, drillers panels, and sandline controls. Halls have been involved with over the rebuilding from scratch of over twenty service rigs.
-
product
Loop / PFC Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
Digital LOOP/PSC Tester
8025 LP
Standard Electric Works Co., Ltd
● Battery is not used.● 3 ½ digit LCD (2000-count).● Backlight function.● 15mA loop measurement which will not trip ELCBs.● Convenient and easier for users to measure the loop impedance directly without bypassing the wires.● Wiring check function.● Over temperature protection.● Over voltage protection.● Built-in voltmeter.● Built-in earth tester.● Built-in loop/psc tester.● Safety standard : EN 61010-1 CAT III 300V EN 61326-1
-
product
Electrical Test Equipment Calibrators
The industry leading series provides by far the fastest and safest solution for calibration of Loop, RCD, PAT's and insulation testers.
-
product
100 Ampere Micro OHM Meters
Introduction: Measuring the line loop contact resistance by bridges is not the ideal method as the test current is only a few milli amperes. Thus the value is not the true value of the contact resistance. Model HL- 100 is a direct reading tester, and uses a test current of 100A DC, resulting in true v alue and accur ate measurements. Model HL- 100 adopts digital circuit technique and is used for measuring contact resistance of switch control equipments at test current of 100A DC. The measurements are accurate as the test is highly stable.HL- 100 is a new, fully automatic micro controlled tester that measures contact resistance at 100A DC with built in printer. The advantages of HL-100
-
product
Multi-function Tester
MFT5010
It can be used to test insulation resistance, continuity, loop impedance and RCCB, earth resistance tester, five major test requirement in the electrical testing industry. Phase indicator. Can check a wide range of 3-Phase Power source from 110V to 600V
-
product
Surge Tester
Qingdao AIP Intelligent Instruments Co., Ltd
Surge tester able to test various coils, motor, stator winding, relay/contactor coil, electric magnetic valve coil etc. and can be applied for maintenance, production line, lab and QC etc. Extension: single surge test or multiple tests options.Large storage: up to 1000 test groups can be established.Automatic determine: manual or auto test mode options and test results would be determined automatically.Support both touch screen and numeric keyboard operating.Data analysis: data can be exported i...show more -
product
TAP Signal Isolation Module
JT 2139
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
product
Downloading Multifunction Tester
ET4500
The new ET4500 tester carries out all the tests needed to verify the safety of electrical installations in domestic, commercial and industrial wiring installations in accordance with the latest regulations.
can be used to carry out 3 wire earth testing and has on board memory to store and download all installation test results for documentation.
Everything about the new ET Series has been designed to save time and make testing easier.Fast, reliable high current and non-trip loop testing comes as standard together with a high level of input protection and a CAT IV safety rating .Supplied with a full range of accessories.
-
product
180V-260V AC Socket Tester With RCD Test (For UK)
1943
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 180~260VAC circuit.*LED indicators & Digital display.*30mA leakage current measurement.*RCD Test.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 11W*Frequency: 50Hz
-
product
Wire Harness Tester
Panther4HT Master- Slave DSU
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This i...show more -
product
Digital Electrical Network Analyzer
1826 NA
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Earth Resistance without the need for poles in the ground or external measuring wires.● Earth measurement uses the real earth current path and the current generated by the electric network, without the need for any disconnection.● The Earth Resistance displayed is exactly the earth resistance that the earth current will need to go through if an earth fault occurs. No need to add all the bonding points and connection paths resistances.● Dis...show more -
product
ICT Software: Interactive Developmetn Encironment ICT ICE & ICT Sequencer
ICT IDE and Sequencer
The ICT software consists of two parts, the interactive development environment ICT IDE and the ICT sequencer. The IDE provides a graphical user interface for convenient creation and testing of these test sequences and allows:- Convenient management of hardware resources via topology editor- Support of several independent embedded testers for parallel test execution- Editing sequences in a text or table editor- Error highlighting during sequencing- Sequence execution (also single step) directly ...show more -
product
Air Jet Erosion Tester
AJ-1000
The state of the art Rtec Air jet erosion tester AJ-5000 allows to test repeated impact erosion test that delivers a stream gas with abrasive particles. The tester comes with close loop temperature control upto 900C. The tester is used to rank erosion of various materials, coatings etc. across a wide range of abrasive particle materials, shape, size at various temperature and impact speed.
-
product
180V-260V AC Socket Tester (For UK)
1941
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*LED indicators & Digital display.*Test for 180-260VAC circuit.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 4W*Frequency: 50Hz
-
product
Earth Ground Resistance Meter
1623-2
The Fluke 1623-2 earth ground tester measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. With the stakeless test method, the Fluke 1623-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps.
-
product
ICI Mace Snag Tester
TF220
TESTEX Testing Equipment Systems Ltd.
ICI Mace Snag Tester. To determine the tendency of fabrics to snag (pull yarn loops from fabric) in normal wear (mace snag).Provided with 4 rotating test cylinders fitted with sleeves of test fabric, mace balls with tungsten carbide points and controlled by a predetermined electronic counter.
-
product
Micro-Ohmmeter and Loop Resistance Tester
LRT 6000
LRT 6000: The right solution for impedance resistance measurement in compliance with all aircraft specifications on plane, helicopter, rocket, army vehicles for both production andmaintenance. It is a very easy-to-use and versatile instrument. Its ergonomics allow the user to use it either placed on the ground or across one's shoulder or chest. Awide back-lit LCDdisplay combinedwith an intuitive keyboard ensures simple and easy operation.
-
product
TEST BOX
6280 TB
Standard Electric Works Co., Ltd
● Wide range of operating voltage from AC 210V/50Hz to 250V/50Hz.● For checking AC voltage.● For checking a RCD tester's test current & time in mA(ms).● For checking a loop tester.● For wiring check (Phase, Neutral, Earth).● For checking continuity.● For checking insulation (The maximum is 1.2kV).● For checking UK16th edition.● Safety standard: EN 61010-1 / EN 61326-1
-
product
200 Ampere Micro OHM Meters
HL-200
Measuring the line loop contact resistance by bridges is not the ideal method as the test current is only a few milli amperes. Thus the value is not the true value of the contact resistance. Model HL- 200 is a direct reading tester, and uses a test current of 200A DC, resulting in true value and accurate measurements. Model HL- 200 adopts digital circuit technique and is used for measuring contact resistance of switch control equipment at test current of 200A DC. The measurements are accurate as the test is highly stable. HL- 200 is a new, fully automatic micro controlled tester that measures contact resistance at 200A DC with built in printer.
-
product
ICI Mace Snag Tester
TESTEX Testing Equipment Systems Ltd.
ICI Mace Snag Tester, to determine the tendency of fabrics to snag (pull yarn loops from fabric) in normal wear (mace snag). ICI Mace Snag Tester complies with ASTM D3939, etc. Please contact us for more information about snagging test.
-
product
Loop Tack Tester
Loop Tack Tester is applicable to measure the tack property of adhesive tapes, pressure-sensitive adhesives (PSA), and adhesive materials according to ASTM D6195.
-
product
Loop Testing
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
product
Multi-Function Electrical Tester
CZ20500
The CZ20500 Multi-Function electrical tester includes some of the latest advances in electrical testing, combining 5 instruments into 1! Insulation, Loop, Phase, RCD, and Voltage testing are all included in the one instrument, making your job of installation testing easier.
-
product
Velcro Tester
TF151
TESTEX Testing Equipment Systems Ltd.
Velcro Tester, to determine the capability of Velcro used for shoes, garments, etc.Cut the specimen 540mm by 20 or 50mm in dimension from the sample being tested into the wheel of Velcro tester to be fitted completely. To subject Velcro (hook & loop) to repeated stripping and peeling for a certain number of times. Use tensile machine (another purchase) to measure its peeling strength (AS) and shear strength (PA) after this test.
-
product
Velcro Tape Fatigue Tester
UI-FT35
Velcro Tape Fatigue Tester is used to test the velcro tape/ hook and loop fastener to repeated closing fatigue resistance ability. Touch and close fastener repeated closing fatigue test is one of the necessary step for velcro strength test no matter for peel strength or shear.strength
-
product
Resistance Tester With Leakage Current (Loop Current)
GT00WD00ZY
*screen display*Double protection insulation*Non-contact measured resistance, safe, fast
-
product
Digital LOOP/PSC/LOAD Tester
2811 LP
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Displays and sound warning if external voltage present.● Displays mains voltage, scroll trough menus.● Checks wiring integrity (LEDs and display).● Single button operation.● Auto-off/auto-ranging.● Combined prospective short circuit current, PSC and LOOP tester.● Built-in carry case, test leads in separate pouch.● Loop test for L-E and L-N and PSC.● Voltage test L-N and L-E.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for special orders.● 60Hz available on request.
-
product
Contact Resistance Tester
Weshine Electric Manufacturing Co., Ltd
The loop resistance tester is used to test the conductive loop resistance of various switchgear, and the test current shall not be less than 100A. Due to the oxidation of the contact surface, poor contact tightening and other reasons, the contact resistance increases. When a large current flows, the temperature of the contact point increases, which further accelerates the oxidation of the contact surface and further increases the contact resistance.
-
product
Earth Leakage Relay
Nippen Electrical Instruments Co.
NIPPEN's Earth Resistance Testers are used for measuring earth electrode resistance, soil resistance, earth continuity, neutral and earth loop resistance, resistance of various components etc.They are used in Railways, Defence, Utilities, Power Plants, Geological Surveys and other Industries.Direct reading type models SET/DET/TET provide direct readings of resistance on moving coil type meters, having a linear scale, 70mm long knife edge pointer and an external zero adjustment.
-
product
Earth Ground Tester
1625-2
The Fluke 1625-2 earth ground tester measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. With the stakeless test method, the Fluke 1625-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps. This technique eliminates the dangerous, and time consuming job of disconnecting parallel grounds, and finding suitable locations for auxiliary ground stakes.
