-
product
PXI 32 Channel I/O, High Side Driver
40-413-001
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
product
Dynamometer
Dynamometers, force and torque transducers available in many models. Buy your dynamometer or force measurment products from Vetek!The difference between a load cell and a dynamometer is that the dynamometer is optimated for fast measurement.
-
product
Qualification Tester
LQ404
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 12 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 3 cabinets. One is for the electronic components with the primary measurement devices and the other two hold the 12 load boxes.
-
product
Through Hole/ Donut Load Cell Compression Only
THC SERIES
Our THC Series through hole donut load cells offer an outside diameter of 2.00 inches and up to six different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Laser Diode Characterization Testing
The Yelo Laser Diode Characterization system performs automated characterization of a laser device. The system will allow the operator to load a single packaged Laser device into a TEC controlled fixture mount. Each test station (LIV, Spectrum, Far Field/Beam Divergence) will then automatically align with the Laser Device in a sequential order and perform the automated tests required of each station.
-
product
Phantom Load Test Set
Is a testing accessory, wisely designed for field testing service. This equipment helps in providing artificial load that is unaltered by the change in power supply.
-
product
PXI General Purpose 2A Relay Module 26xSPDT
40-131-201
These are low cost, general purpose electromechanical relay cards capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin D-type Connector
40-158-103
The 40/42-158-103 is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A. User connection is via a 50-pin D-type male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
Uni-Therm High Current Electrosurgical Analyzer
A unique high power low inductance load bank enables performance testing up to 8 ampere RMS with a duty cycle of up to 100% making the analyzer an extremely versatile test instrument for calibrating and performance testing of conventional and high power electrosurgical generators. The load bank allows testing in a range of 0-5115 with a resolution of over 1000 steps providing high detailed power profiles. The Rigel Uni-Therm also advocates safe working practise by providing all necessary resistors within a single enclosure.
-
product
Networkcontroller
A new set of motorized tables developed by Klocke Nanotechnik allows high strokes at small volumes. The modules are driven by the Nanomotor®. Loads of up to two kg can be moved over centimeters of stroke with down to 2 nm resolution. Manipulation in many degrees of freedom is possible without backlash. The modules NMT xx-L are longer, but thin like a pencil. In most of the NMT-modules position measurement systems can be included without increasing the size. The resolution of the position sensor ...show more -
product
PXI-2564 , 16-Channel, 5 A, SPST PXI Relay Module
PXI-2564 / 778572-64
16-Channel, 5 A, SPST PXI Relay Module—The PXI‑2564 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2564 is fully software programmable. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for switching medium‑ to high‑power signals and loads in military, automotive, or automated test applications.
-
product
Plug-in Modules for High-Performance Testing
D Series
With the invention of the D Series line, Introspect Technology has revolutionized the way product engineers test high-speed digital applications. Our unique plug-in module design allows for high-performance testing on any load board and eliminates the need for cables. Despite the continuous transformation of the test industry in recent years, a growing number of legacy equipment remain in use.
-
product
Load Cell Transducer
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R &...show more -
product
Single Point Aluminium Load Cell
EST-4
Technopark Automation & Control
The EST-4 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 1200 x 1200 mm. This load cell is available in capacities 1000 kg and 2000 kg.
-
product
Roll Force Measurement
Millmate
ABB’s Millmate roll force system is the perfect choice for measuring roll force in both hot rolling and cold rolling mills, thereby achieving correct roll gap settings and force distribution.The system is proven to be exceptionally robust and resilient to high forces as well as aggressive mill agents. The load cells are calibration free, can withstand overloads up to 7 times the nominal force, and have an impressive life length. The load cells come in different sizes from 0.1MN up to 60MN.
-
product
4-Amp Solid-State Single Inline (SIP) Four-Pin Relays
Series BS
Series BS 4-amp solid-state single inline (SIP) four-pin relays are designed for mounting on a printed circuit board. BS relays can withstand very high current overloads. The compact size and triac output make the BS relay an excellent choice for switching medium power resistive loads. All Series BS relays are Zero-Cross switching.Available options include:BS24D4A 4Arms, 15-280Vrms, 600Vpeak Load; 3-10Vdc Control
-
product
10W to 100W - Single Output
DRL Series
*High Efficiency, up to 90%*Low Profile for Building Automation*Class II Double Insulation*ErP Compliant Design*Low No Load Power Consumption*UL 1310 Class 2 Compliant*SEMI F47 Compliant
-
product
SparkFun Load Sensor Combinator
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat's nest of wires. The Load Sensor Combinator was created to combine the 12 wires found in a bathroom scale into the standard four-wire Wheatstone bridge configuration.
-
product
Damping Pads
With damping pads from the SLAB series, ACE provides solutions to effectively slow down loads impacting large and small surfaces. This means that these products are found in a wide range of damping technologies from ACE where oscillation begins or where damaging impacts in construction designs need to be slowed over a large surface.
-
product
LXI Scalable Matrix Chassis
65-200-001
This LXI scalable matrix chassis offers you a solution that can be easily re-configured by the insertion and removal of up to six LXI matrix plug-in modules (detail in the tables below). It is purchased as an empty chassis with a quantity of plug-in modules required for a particular matrix size. Unused chassis slots are blanked off by the supplied blanking pieces. Cooling is provided by rear fans and front air intakes ensuring no wasted space when the chassis is rack mounted. The cooling system is adaptive to its operating environment to ensure the acoustic noise is minimized when used in quiet laboratory environments and low load conditions.
-
product
CAM/TRAC Test Kits
Series 47
The VP Series 47 CAM/TRAC mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 47 provides interface compatibility using the Virginia Panel ITA G12 interface. The ITA frame is offered as an option for those wanting to provide their own ITA Interface.
-
product
Waveform Amplifier
TS250
The TS250 Waveform Amplifier is a one of a king instrument perfect for amplifying signal generators. It is designed to amplify voltage, power or current for while driving heavy (low ohmic) loads. The TS250 offers eight voltage ranges to choose from ±10V to +65V. The TS250 output up to 6A peak current. To obtain higher current, parallel connect two or more TS250 in as shown in the Application Section.
-
product
Common Metallic Pendulum Impact Testing Machine
JB-(C/D)
Jinan Testing Equipment IE Corporation
KB- (C/D) common type metallic pendulum impact testing system is the basic model for impact tester. The metallic pendulum impact tester is used to determine the impact resistance of metal materials under dynamic load and capable of doing a large number of impact tests continuously. The display method for the models is different, respectively there are analog dial display, touch screen digital display and computer display. For the later two models, it can display the impact power, impact toughnes...show more -
product
Multi-Channel Battery Testing
The Multi-channel system includes turnkey integration of Greenlight's environmental chamber, load bank, power supply and data acquisition system, all housed in 19" rack towers.
-
product
RS LabSite® modulogic
RS LabSite® modulogic is a comprehensive and adaptable software suite conceived for introducing service loads into individual components or complete vehicles, or performing calculations within the framework of Virtual Prototyping (standardized loadsequences, virtual generation of load data). This enables you to stay in full control of all tasks that follow the acquisition of measurement data in the proving ground.
-
product
1000W Ferroresonant Power Supply
Series PRR
Kepco's PRR are 1000 Watt rack mounted laboratory systems power supplies that offer the low cost and very high dependability of ferroresonant voltage stabilization.The ferroresonant stabilizing technique provides extraordinary isolation from a wide variety of source noise. It is inherently short-circuit proof and cannot expose delicate loads to overvoltage hazards. Hence no crowbar, fuses, or bounding circuits are needed. Ferroresonant power supplies use no noise-producing switches or oscillators. Voltage setting is independent of delicate control settings or diode references and requires no comparators, references, or limiters. Efficiency is 70-80%.
-
product
Transformer Tester
Kvtester Electronics Technology Co.,Ltd
High precision instrument for measuring characteristic parameters of transformer capacity, no-load and load. The instrument is a multi-function measuring instrument, which is equivalent to the usual two kinds of test instruments: the transformer capacity tester + transformer characteristic parameter tester. The utility model can precisely measure a series of power frequency parameters of a plurality of transformers, such as the capacity, the type, the no-load current, the no-load loss, the short circuit (load) loss and the impedance voltage.
-
product
Temperature Rise Tester
WS-1
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right. It is designed and manufactured according to IEC884－1, GB2099.1-2008 and other relevant standard of electrical accessories.
-
product
Test System
LB301
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
product
35W Low Profile Triple Output Power Supplies
CUT35
The triple output CUT35 and CUT75 power supplies have two independent, isolated, converters, one for the main 5V output, and one for the auxiliary outputs. This topology provides several benefits - no minimum loading, enhanced load & line regulation and the ability to connect the auxiliary outputs in series to generate either a 24V or 30V output. This flexibility makes it suitable for use in a wide range of process control, broadcast, test & measurement, medical and industrial equipment applications.
