-
product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.T...show more -
product
Strain Gage Testing
Response Dynamics Vibration Engineering, Inc.
Although strain measurement is often a key part of a root cause diagnosis, our analyses often also involve measurements of other parameters such as acceleration, relative displacement, pressure, temperature, flow, speed, load, dynamic stiffness, etc, to explore multiple parameters that may have a cause/effect relationship with the problem at hand. These measurements form part of a fact based hypothesis for the cause of the problem at hand. We use stain gauge testing and/or stain modeling and analysis, in conjunction with our structural dynamics expertise to characterize all the important pieces of the puzzle that come into play with dynamic strain issues (See Diagnostic Testing).
-
product
Battery Test
1260
*Basic Battery Load Test*Battery Analysis*Mac*Test*Bad Cell Indicators*Testing the Starter Motor*Low Temperatures Effects
-
product
PXI 5A Power Multiplexer, 1-Bank, 48-Channel, Isolated Common, Independent Isolation
40-651A-111
The 40-651A-111 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
product
Bipolar Power Supplies High Power, 4-quadrant, Analog/Digital/Local Control, Low Ripple/Noise
Series BOP-MG/ME, BOP-EL/GL
The BOP High Power are true 4-quadrant programmable voltage and current power supplies. 4-quadrant operation means that they are capable of both sourcing and sinking power. These bipolar power supplies pass smoothly through zero to provide ± voltage and ± current. The BOP High Power use switch mode technology for low dissipation and function as regenerative (recuperative) loads and connected to an active load.
-
product
Power Supply 303d
Power stabilized POWERLAB series are high precision current sources with variable voltage and current over the entire range . They can operate in different modes of stabilization voltage or current switched automatically with adjustable limit value of the load current at any point in the range.
-
product
Slip-Ring Motor Starting Panels
Rotor Starter
The Slip-Ring Motor Starters are based on the series of resistors that are applied to the rotor circuit to control the speed/torque characteristics of the motor. Rotor starters are mainly used for the motor starting applications requiring high-starting torque like loaded belt conveyors in mining industry. By external resistors, it is possible to shift the motor maximum (break-down) torque up to starting torque point for motors under heavy loads during start-up. The resistors are splitted into ...show more -
product
Battery Test device
ATGB 1200
The ATGB 1200 is a battery tester for all standard battery technologies aimed at quality assurance, production and product development. Advantages of the ATGB: Creation of customized test sequences. Generation of load curves and peaks. Temperature measurement at the battery
-
product
Anti-Tamper Sub-Assemby (DC Immune CTs + Potential Transformer)
Shanghai Powoo Industry Develop Group Limited
ATS can provide double loop current sampling and power supply for measuring unit of static meter. When load voltage, static meter can in normal condition without single-channel current.
-
product
Triple Output DC Power Supply, 60V/3A (2x) & 5V/3A; 375W
U8032A
Keysight now extends its range of basic DC power supplies to offer 375watt power range, making it an ideal power source alternative in electronics manufacturing, research and development as well as the education sector. The U8032A, basic DC power supply, is a manual triple-output power supply with sequencing capability. With this function, users can generate output sequences with minimal programming skills. Each power supply is also built with excellent load regulation and clean output noise for continued stability. With these and many other features, you get a solid and reliable triple-output power supply at an unsurpassed performance.
-
-
product
Miniature Shock Absorbers
Miniature shock absorbers from ACE are tried-and-tested quality products used in millions of industrial designs throughout the world. They optimize machines in an equally reliable and effective way by decelerating loads quickly and without recoil.
-
product
PXI 10A Power MUX 8-Bank 4-Channel
40-661-001
The 40-661 is a single pole PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
product
Miniature Instantaneous Relays
CU-D Series
Heavy duty miniature power relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads. Equippedwith weld no transfer contacts.
-
product
Bench Power Supply, Linear, Programmable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2710
The 72-2710 from Tenma is a single channel programmable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
product
Bi-axial Dynacell Load Cells
2527 Series
During tests carried out on servohydraulic machines, elements of the system are subject to acceleration. As a result, in addition to the force applied to the specimen, the load cell also reads forces resulting from its own movement and the mass of the grips and fixtures attached to it. Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages:*Reduces dynamic load errors which can be a significant percentage of reading *Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
product
High Speed Data Logger
9330
The Model 9330 displays 24-bit resolution and has an impressive 3750Hz update rate. Incorporating peak and valley capture, it can store up to 6 sensor calibrations and measurements from load cells or torque transducers can be logged at 1000Hz to a standard SD card. This data can then be downloaded to a PC via the built-in USB port and Windows compatible software for off-site analysis. Adding further versatility, the rechargeable battery can power up to 4 x 350 ohm sensors, but also offers up to 300 hours stand by time and up to 20 hours continue use.
-
product
DC Electronic Loads
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.Both static and fully dynamic DC loads are offered. With dynamic functionality 2 levels of load current can be set. The rise and fall time can then be adjusted together with the time period spent at each level. The load can also be made to follow complex waveforms by tracking an external arbitrary oscillator input.
-
product
Durable Hand-Held Battery Tester
6029
• Test 6 & 12 Volt batteries, alternators and starters• 125 Amp fixed load• Made in USA of US and Global Components
-
product
Flexometer
EKT-2002GF
By means of applying constant load and compression frequency to the test specimen, this instrument could help the user to understand the history of Heat Built-up and dynamic fatigue poeperties of rubber compounds. For example, while tests the tire compound, it could provide the information of rolling resistance. Pt100 temperature sensor, temperature controller in PID parameters control, and air circulator are adopted to ensure the stable temperature control.
-
product
Static Jack System
The servo actuator system applies static test force loads on structures at high precision to obtain their mechanical characteristics on an experimental basis.
-
product
Microwave Comb Generator
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
-
product
Remote Displays
HS Series
Load cell / scale remote displays are driven from another digital indicator or amplifier. Often used on bridge cranes and truck scales, or in any situation which the person needing to see the scales displayed weight is too far to see the smaller standard indicators. Many styles, digit sizes, indoor and outdoor models are available.
-
product
DC Resistive Load Banks
LB-Series
Eagle Eye offers multiple DC Load Banks ranging from 10 480 VDC at 1 amp or 5 amp Resolution. These load banks offer a simplistic solution to UPS Battery Load Testing. Each load bank is easy-to-use with an LCD display operator control panel and user-friendly fan switches, load step switches, and master load switches. UPS load testing stimulates a real-world performance demand of a critical power
-
product
3kW Electronic Load
PT04-FC
For Fuel Cell testing and Power Supply testing. This model has been developed to accommodate testing of both Fuel Cells and low Voltage Power Supplies, (including 24V telecommunications power systems or Power Supplies). It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
product
PXI 12xSPDT 16A Power EMR Module
40-161-101
This40-161 range of PXI power relay modules is available with achoice of 16 x SPST, 12 x SPST, 10 x SPST, 12 x SPDT and 6 x SPDT power relays, for switching loads up to 16A at250VAC. These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
product
Test Automation System for Driveline Testing
STARS Driveline
STARS Driveline is an integrated automation, acquisition and control system that provides a broad range of application functionality in a single, powerful environment. It has been designed to fulfil the specialist requirements and applications for driveline testing from simple modal testing on two or four wheel drive systems, to RLS simulation or advanced applications such as service load replication (SLR).
-
product
Harness Design and Manufacture
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with e...show more -
product
Force Logger Sensor
NUL-211
This sensor can measure the mass to weightrelationship and study how different pulleysystems affect the effort needed to lift weights.It can also be used to measure push/pull forcesand impacts. There is a hook at the bottom of the force sensor that can be connected to various pulling loads.
-
product
48V / 250 Amp Load
EL15-48M
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
