-
product
Compact Measurement System For Steel Wire And Rods With Small Diameters
A glowing hot wire is pulled through the rolling mill at about 120 meters per second during ongoing production. Speed, high temperatures and dirt are special challenges for a high-precision measuring system. Our solution is the Contour Check Wire. It is specially designed for the geometric measurement of wires, rods and rebar and, at 800 Hz, offers the optimum measuring rate for accurate data acquisition. In the uniaxial version, you can check the diameter; in the two- to three-axis version, the ovality can also be determined. The small dimensions and light weight allow a quick and easy integration of the Contour Check Wire into the existing line.
-
product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
product
Electronic Loads
Series EL
The EL Series is a line of modular aircooled, DC electronic loads used to test power sources such as batteries, power supplies, generators, chargers, fuel cells, etc.Power ratings start at 1KW; standard models have maximum test capabilities of 50, 200, 400 and 600 volts. High current and power operation are achieved via parallel connection in a master/slave configuration. Individual modules are capable of up to 5KW and 800 amperes.
-
product
6TL36 Plus In-line Test Handler w/Bypass
EA923
- Test handler 6TL36 Plus.- Dual line (bypass)- 1096 x 1875 x 1851mm [WxDxH]- Expandable to form a group with several 6TL36 modules (adapt line to production volumes).- ICT, FCT with RF, ISP or Combined test (ICT+FCT)- Servocontrolled DUT stop (stopper-less system)- Exchange time 3,2s- Max. PCB dimension 600x450mm- 19” rack space for instruments integration: 28UH- Receiver 25 slots in probe plate + 4 slots in push plate- Automatic Conveyor width adjustment- Optional Return Conveyor- High dynamics conveyors (1500 mm/s)- 90mm Top-30mm Bottom Component clearance- SMEMA and Hermes standard- CE
-
product
Digital Telephone Hybrid
DMTH4
The DMTH4 integrates telephone lines, video codecs and external audio sources into the digital bus structure of DM Series processors so these sources operate as though they are another microphone or audio input in the sound system. The unit is much more than just a telephone interface. Instead, it is a complete DM Series digital matrix processor, with a 3-in/24-out digital matrix, automatic mixing and comprehensive signal processing on every input and output. In essence, it simply connects to telephone lines, video codecs and external audio sources instead of mic/line inputs and outputs and integrates seamlessly with DM Series matrix processors.
-
product
PXI Analog Output Module
PXI Analog Output Modules support both static and software-timed voltage output applications. Modules also include 5 V TTL/CMOS digital I/O lines. Some PXI Analog Output Modules can deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. These advanced features enable you to use the PXI Analog Output Module to replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.
-
product
Digital RCD/RCCB/GFC/ELCB Tester
4112 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 Characters LCD.● Very low consumption.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Zero Crossing Circuitry permit testing at 0° or 180°.● Disconnection Phase Polarity Shown on LCD.● Auto off and off override.● Polarity Trip indicator (Positive or Negative Phase).● Wiring polarity indicator.● Measure voltage between line and earth before testing.● Indicates frequency of voltage L-E.
-
product
Comprehensive Oil Analyzer For Engines
MiniLab EL
Engine oil analysis is a reliable and mature non-destructive testing (NDT) technique used to monitor the condition of the engine in development, on the production line and for in-service maintenance. High performance reciprocating engines and jet turbines are complicated mechanical systems with many high speed moving parts.
-
product
CO2 Concentration and Temperature Transmitter
T8448
CO2 concentration and temperature transmitter with serial RS485 output is specially designed for use in exacting interiors in building energy management and HVAC systems. It designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets. Large dual line LCD is possible to switch off. Computerized design ensures long term stability and fail indication. Transmitter is designed for use in non-aggressive environment.
-
product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
Temperature Calibration Equipment
We offer wide line of temperature calibration equipment for calibration of contact type sensors (Baths/furnaces) and non contact type sensors (Black Bodies), available in temperature range -80°C to 1700°C.
-
product
CB-37FH, 37-Pin DSUB to Screw Terminal Block w/ Horizontal DIN-Rail Mount
778673-01
37-Pin Female D-SUB to 37-Pin Female Connector, Horizontal DIN-Rail Terminal Block - The CB-37FH is an unshielded terminal block that provides access to NI data acquisition devices with 37-pin female D-SUB connectors. The CB-37FH mounts in line with the DIN rail, and it features screw or spring terminals for connecting to 37 I/O signals, 12 to 30 AWG.
-
product
CO2 Concentration Transmitter
T5240
CO2 concentration transmitter with 0-10V output is built in a durable case. Output range is user adjustable. Large dual line LCD is an advantage. Display is possible to switch off.
-
product
EMI Filtering Analyzer
RS Analyst™
With RS Analyst circuits can be analyzed prior to fabrication to determine whether radiated susceptibility requirements will be satisfied. RS Analyst is ideally suited for predicting the effectiveness of EMI filtering for power line and signal line filters and for determining the effects of cable shielding and shield terminations.
-
product
Calibration
General purpose calibration/diagnostic tool.Built in precision resistors.Simple manual contact/routing/resistor selection.4mm terminal posts on key device connections.In line mode to aid fixture wiring/DUT debugging.Comprehensive documentation including circuit schematics.Connecting cables.
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the...show more -
product
AC Power Source, Frequency Converter
BL1350 Series
Behlman's BL1350 AC Power Supply / Frequency Converter / Inverter, requires just 3.5" of rack height, and weighs as low as 45 pounds, yet it delivers 1350 VA of quality AC power. In the BL 1350, you'll find the quality features you expect from Behlman, fully adjustable frequency and voltage, total harmonic distortion of less than 0.5%, high efficiency, plus excellent line and load regulation.
-
product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, P/LL/UL/S , Programmable Amplitude Balance
LS-16-R1-24SPLUS
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
product
Coaxial Components
Surge arrestors are designed to protect wireless base stations, switching centers and transmission lines fromthe damaging effects of extreme high voltage surges caused by lightning strikes. The RFS lightning protectiondevices are designed and tested to the most demanding specifications. They are rated to protect against bothdirect and indirect multiple strikes in the harshest environments imaginable. Their rugged construction utilizes solid metal housing, and superior plating, which results in outstanding system protection and operatingcontinuity.
-
product
Uncooled InGaAs Line-Scan Camera with Square Pixels
Lynx SQ Series
The Lynx square (SQ) series, based on an in-house developed linear InGaAs detector, offer affordable short-wave infrared (SWIR) line-scan imagers. The Lynx SQ cameras are able to image line rates up to 40 kHz for demanding machine vision applications. The cameras come with an industry-standard CameraLink or GigE Vision interface.
-
product
Bench Power Supply, Single, Adjustable, 1 Output, 0 V, 40 V, 0 A, 5 A
72-7295
The 72-7295 is a 40VDC Laboratory Grade Switching DC Power Supply with precision coarse and fine output voltage and current limiting controls. The output Overvoltage protection protects voltage sensitive load by instantly shutting down the supply when the output voltage goes beyond the set voltage due o line surge or otherwise. Current limiting control with automatic cross over of constant voltage and constant current modes makes this unit ideal for R&D work in laboratory situations.
-
product
Universal II Level System
The Universal II is a two wire level transmitter that eliminates the need for line power in the field and saves costs for additional hardware. It provides reliable level measurements in all kinds of process liquids, slurries, granulars and interfaces.
-
product
Instrumentation Amplifiers
Analog Devices instrumentation amplifiers (in-amps) are precision gain blocks that have a differential input and an output that may be differential or single-ended with respect to a reference terminal. These devices amplify the difference between two input signal voltages while rejecting any signals that are common to both inputs. The in-amps are widely used in many industrial, measurement, data acquisition, and medical applications where dc precision and gain accuracy must be maintained within a noisy environment, and where large common-mode signals (usually at the ac power line frequency) are present.
-
product
Xhorse EWS-3
For writing through K line in ews-3. All you need to do is to connect adapter to the EWS 3 connector and solder one cable in the marked place according to the instructions.
-
product
NI-9775 , ±10 V, Up to 20 MS/s/ch, 14-Bit, 4-Channel C Series Digitizer Module
784539-01
The NI-9775 provides referenced single-ended analog inputs with two timing modes for applications such as fault detection in electrical transmission lines or structural failure events. You can use the NI-9775 to measure finite samples up to 20 MS/s/ch to capture fault detections or to measure continuously at up to 4 MS/s. You also can use the built-in analog reference trigger to assist with high speed phenomena. Additionally, the NI-9775 supports waveform streaming at a lower sample rate.
-
product
AERINOS ProfiSens IOT
Infinite Industrial Informatics Lt
AERINOS® ProfiSens is a local area wireless IOT platform. It comprises wireless sensor nodes and a 3G Data Concentrator/ Gateway. Using ProfiSens, you can deploy anywhere your own IOT network. The battery powered, wireless End nodes, offer reliable communication and outdoor enclosures to satisfy a variety of measurement and monitoring applications. The acquired sensor data wirelessly transmits to the data concentrator with 3G, GSM/GPRS connectivity, which forwards data files to an FTP server and...show more -
product
TWT Test Set
Polarity designs and manufactures the most reliable Microwave Tube Test Sets in the industry. Polarity understands the delicate structure of microwave tube devices and has built an extensive product line supporting the manufacturing process. Polarity designed and developed this Microwave Tube Test Set with the following specifications:
-
product
FFT Analyzer
FFT Spectrum Analyzer and Frequency AnalyzerThe Dewesoft FFT spectrum analyzer has it all. Top performance, advanced cursor functions, high freely selectable line resolution, flexible averaging, and advanced functions for in-depth frequency analysis.
-
product
Test Equipment Grade Switches
Multi-Tech Industries also manufacturers a line of quality instrument-grade electromechanical switches for commercial, industrial, military, institutional and OEM applications. Rotary switches (open frame, enclosed frame), thumbwheel, keyreader and other types are available to be integrated into your process controls or test instrumentation. Standard and custom switch designs can be modified to meet specific customer requirements.
-
product
Digital I/O Board, 32 Isolated I/O Channels, 24 V.
APCI-1500
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs