Lamp
Radiate light or heat.
See Also: Flash Lamp, Arc Lamp, Flashlamp, Gas Lamp, Fluorescent Lamp, Headlamp
-
product
LED tester
Ecopia's LED tester is good to measure both electrical(I-V curve) and optical(Spectra, Light intensity) properties of LED chip, LED lamp, SMD type at the same time.It also makes it possible to see LED sample's construction , seeing through microscope. LED tester main body flow input current ,and emitted light from the LED sample is focused on lens of microscope.From this process, our LED tester can provide repeatable tested results and minimize error values and improve convenience of how to use.
-
product
Goniophotometer Test System For Led Lamp
LCG-1680B
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
product
Professional Cordless Circuit Tester
CT8002
No Ground or clip required. No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance Electronic circuitry. Safety V-groove needle accessory for piercing and carrying. Negligible current draw ( 20 micro-amps) is 10,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 3 and 28 Volt DC in battery powered systems.
-
product
Output Characteristic Analyzer of Electronic Ballast
UI2002
• Measure lamp voltage, lamp current, lamp power, oscillatory frequency, filament current, guided cathode current, and crest factors • Measure changing curves and values of startup lamp voltage, lamp current, filament current, cathode current from 0 to 5 seconds, as well as the pre-heat time • Accuracy: Class 2 • Data and curves printable. All the data and curves can be displayed after being connected with PC
-
product
Multiple-Bus Architecture Cable/Harness Test System
CKT1175-MBA
The CKT1175-MBA (for multiple-bus architecture) will provide seamless testing of electronic racks, panels and chassis containing passive and active components such as relays, solenoids, switches, circuit breakers, lamps and LED's, diodes, resistors, capacitors, etc. This functionality is made possible by a switching matrix that is up to 10 levels deep, plus a multiplexer that controls the various stimuli sources, instrumentation connections, and external energization outputs.
-
product
Laser-Driven Light Source (LDLS)
EQ-77
Based on the highly successful Laser-Driven Light Source (LDLS)technology, the EQ-77 offers the highest radiance and irradiance availablein a truly broadband white light source. The EQ-77 features a compact lamp house, with clean construction that ensures long life and ultimate stability. With a 170nm-2100nm wavelength range, and a choice of source dual-beam output or a single-beam output with retro-reflector, the EQ-77 is flexible for a broad variety of applications. Researchers using light for...show more -
product
Compressed Air Monitor and Alarm
SENTRY
The Edgetech Instruments Model SENTRY detects upset conditions in compressed air systems by constantly monitoring dew point and pressure at the system header or dryer output. The SENTRY alarms when a loss in pressure or high dew point is detected. This information is valuable in detecting compressor failures, system leaks, or drops in dryer performance. A pulsing audible alarm and strobe lamp provide quick notification of upset conditions. The SENTRY also provides a local display of pressure, dew point and system status as well as 4-20mA analog output and alarm relay contacts.
-
product
Spectroscopic Reflectometer
SR Series
Angstrom Sun Technologies, Inc.
Spectroscopic reflectometer (SR) tools are relative low cost and easy to use. To ensure accurate measurement on spectra, a long working distance and also adjustable working distance set up are professionally designed and considered. Since reflection spectra measurements require to use known reference to calibrate light intensity, it is hard to image that user could get accurate spectra without optimizing signal during such calibration because reference thickness is different from sample substrate's thickness in most of cases. Adjusting power output to lamp is our another consideration in ensuring a good measurement by reducing non-linearity effect of the detector.
-
product
GO-SPEX500 Goniospectroradiometer
Hangzhou Everfine Photo-E-Info Co., LTD
Suitable for all kinds of indoor lamps, flood lamps, road lighting lamps and all kinds of light distribution performance test, total luminous flux, luminaire efficiency and electrical parameters (voltage, current, power, power factor) measurement.Test data can be saved as IESNA(*.ies), CIBSE(*.CIB), EULUMDAT(*.LDT), CIE(*.cie), CEN(*.cEN) and other formats, which can be directly used as the input data of international general lighting design software.
-
product
Almanac Time Switch
IM1754
Almanac Tme Switch is a real time timer which can be used to switch electrical appliances like street lamps, garden lights, corridor lights, neon signs etc. as per time of the day. The timer has built in Almanac timings fixed in Nonvolatile RAM so that the user does not have to programme the unit from time to time. This Almanac time switch has added advantage over daily dial or weekly timers. Timer provides two outputs to drive contactors of different ratings. These outputs can be used with different combinations to achieve desired output. Timer is provided with manual override facility. Optional detachable external keyboard unit provided to avoid unauthorized access.
-
product
TO-5 Hermetically Sealed Package, Through-Hole Mounted, Non-Latching DPDT, with Low-Power Coil
Part No. 732
TO-5 hermetically sealed package, through-hole mounted, non-latching DPDT, with low-power coil.Available options include:732D - coil transient suppression diode732TN - coil transient suppression diode, and transistor driverResistive: 1 Amp/28Vdc Inductive: 200 mA/28Vdc (320 mH) Lamp: 100 mA/28Vdc
-
product
Programmable Setpoint Relay Protection Relay, Trip Relay
CRD-005 and CRD-020
CRD-020 Programmable ac current set-point relay setting for threshold levels, over and under-currentoperationbullet CRD-005 Programmable dc voltage and mA set-point relay setting for threshold levels, over and under-voltage operationbullet CRD-005 internal DIP-switches allow for either 0-1mAdc or 0-10Vdc operation, and may be set for under-alarm or over-alarm relay operationbullet CRD-020 internal DIP-switch allow configuration of the ac current range to either 0-5A, 0-10A, 0-15A or 0-20A and th...show more -
product
Phase Sequence Indicators (Contact Type)
855 PR
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
product
Halogen Moisture Analyzer
LD-LHMA-A21
Halogen moisture analyzerLD-LHMA-A21with benchtop design has embellished automatic double doo, silent opening for the heating chamber. Incorporated with halogen heating lamp for rapid determination of moisture content and dry weight of test sample. The sample is effectively placed in heating chamber at 35 cm height produces accurate results. The user-friendly LCD touch display shows test curve data and other test parameters.
-
product
PXI 50 x DPST Electromechanical Relays
40-146-202
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
Electronic Inspection Systems
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
product
Goniophotometer Test System For Led Lamp
1680A 1680B
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341,the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
product
Integrating Sphere With Holder Base
IS-*MA
1. The hold base can bear max 20kg, it can expanding to test all lamps such as E27/E40, all tubes such as T5/T8/T12, and all kinds of luminaries2. The hold base can be installed in the ceiling or down, it can be adjusted the height3. Hold base has four power cables connect to the outside Power Supply and max is 5KW4. The holder base is detachable. For some kinds of light sources you may need to change the position of the holder base.5. Diameter: IS-0.3M (0.3m), IS-0.5M (0.5m), IS-1.0MA (1.0m), IS-1.5MA (1.5m), IS-1.75MA (1.75m), IS-2.0MA (2.0m). Other sizes can be designed according to the customer’s request.6. The painting of integrating spheres is according to CIE Pub. No.84 (1989)
-
product
Modular UV Curing System
RC-800
Modular system offering single lamp or dual lamp configurations for low heat, fast throughput UV curing.
-
product
FLuorescent Lamp And Ballast Tester
2210-20
Milwaukee Electric Tool Corporation
The Milwaukee 2210-20 Fluorescent Lighting Tester is a new to world tool that tests fluorescent lighting fixtures and cuts troubleshooting time in half. The Fluorescent Lighting Tester delivers complete Lamp, Ballast and Pin testing. Test Lamps before or after installing, and test without dismantling the fixtures.Recognized for its innovation, the 2210-20 Fluorescent Lighting Tester will dramatically improve the productivity of professional electricians and maintenance technicians. Instead of a “replace and hope” strategy, users can test their lighting fixtures faster and easier. The 2210-20 Fluorescent Lighting Tester solves a top residential, commercial and industrial application.
-
product
Complete Testing Solutions
System includes a lamp and monochromator for a tunable light source, which is coupled to a high sensitivity source meter with measurement software. This user-friendly system is the most powerful Spectral Response system currently on the market, but its true power is the ease of upgrading from the base PTS-1 to the more powerful PTS-2-QE (Quantum Efficiency) or PTS-3-CPM (Constant Photocurrent Method). Designed for researchers who have limited budgets but want to start work immediately, this allows the ability to do baseline studies until additional funding for the full QE or CPM system becomes available.
-
product
Turbidimeter
DRK6600-200
Shandong Drick Instruments Co., Ltd.
The main technical parameters:Source: Tungsten halogen lamp 6V, 12WReceiving elements: Silicon photocellMeasuring range NTU: 0.00-50.0; 50.1-200; (automatic range switching)
-
product
Voltage Detectors & Others
Voltage Detectors, Circuit Breaker finder, Portable working lamp are Indispensable equipment which must always accompany the technician. Its essential characteristics are an extreme handiness, a very high protection degree and easiness of use.
-
product
PCE-2000UV_1.5 Ultraviolet Light Radiation Measurement System
Hangzhou Everfine Photo-E-Info Co., LTD
PCE-2000UV UV light source radiation Measurement system can realize the measurement of the relative spectral power distribution of ultraviolet LED, UV fluorescent lamp, UV light source, peak wavelength, half-peak wavelength, spectral radiation flux of UV-A/B/C, and the total radiation flux in specific wavelength.
-
product
Lamp Cap Temperature Rise Test System
CX-T1
Shenzhen Chuangxin Instruments Co., Ltd.
Lamp Cap Temperature Rise Test System is according to IEC60360-1998 and GB2512-2001(Standard method of measurement of lampcap temperature rise). It is used to test the working and environmental temperature as well as temperature-rise of the burner and lamp. It meets the requirement of IEC and GB Standards
-
product
Near-field Goniophotometer
RiGO801
TechnoTeam Bildverarbeitung GmbH
Correct determination of the luminous intensity distributions (lid) of lamps and luminaires far within their photometric near-field range. Capture of ray data.
-
product
Halogen Moisture Analyzer
LD-LHMA-A12
Halogen moisture analyzerLD-LHMA-A12with benchtop design, user can manually open the door of heating chamber for analysis. Incorporated with halogen heating lamp for rapid and uniform heating, it determines the moisture content and dry weight of the test sample. It continuously measures and immediately display the loss of moisture and weight on backlight LCD screen during test.
-
product
Solar Spectrum Test Chamber / Solar Radiation Test Chamber
WEIBER Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instrum...show more -
product
TO-5 Hermetically Sealed Package, Through-Hole Mounted, Magnetic-Latching DPDT
Part No. 420/422
TO-5 hermetically sealed package, through-hole mounted, magnetic-latching DPDTAvailable options include:420D/422D - coil transient suppression diode420DD/422DD - coil transient suppression diode, and reverse polarity protection diodeResistive: 1 Amp/28Vdc Inductive: 200 mA/28Vdc (320 mH) Lamp: 100 mA/28Vdc
-
product
DUV-VIS-NIR Light Source
Angstrom Sun Technologies, Inc.
Angstrom Sun Technologies Inc Introduced high performance DUV-Vis-NIR light source for photometry and ellipsometry applications. This light source covers from 190 to 2500nm wavelength range, with capaility to remote control from computer program with TTL level signals. Dual lamp design offers balanced intensity output. Integrated timer provides conveneience to replace lamps per lamps' lifetime...