Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
PCI Express
PCIe
PCI Express (PCIe) has become the leading interconnect technology to succeed the Peripheral Connect Interface (PCI) architecture. The PCI Express(PCIe) architecture retains the PCI usage model and software interfaces for investment protection and smooth development migration. The technology is aimed at multiple market segments in the computing and communication industries, and supports chip-to-chip, board-to-board and adapter solutions. PCI Express 5.0 currently runs at 16GT/s or 32Gbps per lane in each direction, providing a total bandwidth of 128GBps in a 16-lane configuration which is the largest size in use.
-
product
2-Channel 3.6 GHz or 4-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 58741
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1-channel mode with 3.6 GHz, 12-bit A/Ds- Two or four 2-channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one- or two-channel DDCs (Digital Downconverters)- 4 or 8 GB of DDR3 SDRAM- µSync clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA...show more -
product
Connection Units
Leuze electronic GmbH + Co. KG
All peripheral devices – such as sensors, safety switches and cameras – require a connection to the fieldbus or a control unit. Depending on device type and area of application, our modular connection units offer variable interfaces that enable simple connection of the devices directly to the fieldbus and thus ensure simple integration of new devices in the system.
-
product
MIL-STD-1553
The Avionic Interface MIL-STD-1553 products offer solutions for flight test instrumentation (FTI), for data acquisition, for protocol analysis, embedded IP solutions and COTS applications.
-
product
200 KHz LCR Meter w/RS-232 Interface
LCR 200
Measurement Parameters : Z , Ls , Lp , Cs , Cp , DCR , ESR , D , Q , and £c. Test conditions : 100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz Basic Accuracy 0.1% ; Test Voltage: 1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only). DMM Functionalities. Dual LCD Display with LED backlit
-
product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - XMC
Model 71660
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Amplifier
C-Band
Amonics offers polarization maintaining EDFAs for various applications. Including free space communications, coherent beam combining, and detection system. The output light is linearly polarized with high polarization extinction ratio. The compact turnkey benchtop or 19" rackmount instrument incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power adjust control knob and optical connectors. A RS232 or Ethernet computer interface is also equipped.
-
product
Active Probe, 1 GHz
N2795A
The N2795A is a new generation of low-cost, single-ended active probe with the AutoProbe interface. The probe integrates many of the characteristics needed for today’s general-purpose, high-speed probing - especially in digital system design, component design/characterization, and educational research applications. Its 1MΩ input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT. This, accompanied with superior signal fidelity, makes this probe useful for most of today’s digital logic voltages. And with its wide dynamic range (±8 V) and offset range (±8 V), the probe can be used in a wide variety of applications.
-
product
8-Slot, 3U PXI Chassis
GX7800
The GX7800 is a compact, 8-slot PXI chassis that can accommodate up to 7 instruments as well as an embedded 3-slot PXI controller or an external bus controller such as a MXI interface. The GX7800’s compact 3U form-factor occupies only 9 x 18 inches of bench space, making it ideal for benchtop or space constrained applications.
-
product
Transducer with RS485 Interface
RS485 Temperature, Humidity, Atmospheric Pressure and CO2 Transducers.
-
product
Mass Interconnect Solution
SCOUT
SCOUT is an innovative pull-through Mass Interconnect solution specifically designed to deliver the full performance potential of the PXI platform at the ATE interface. SCOUT, featuring DAK (Direct Access Kit) connectivity, enables system designers to limit or eliminate traditional instrument cables by replacing them with DAK connection modules that utilise PCB, flex-circuit or short wire connections.
-
product
YODA Profiler
The YODA profiler (“Yoing” Ocean Data Acquisition Profiler) is a “tow-yo” instrument to profile the water column with high spatial resolution from small boats without occupying much space. The instrument is provided with a deployment winch and sensors measuring conductivity, temperature, pressure, chlorophyll, turbidity and dissolved oxygen. The brush at the top of the instrument allows for a stabilizing effect on the free-fall sinking speed, which is approximately constant at 0.2 m/s. All data are stored internally and downloaded into a PC through a wet-connector and interface.
-
product
SparkFun Spectral Sensor Breakout
AS7262 Visible (Qwiic)
The SparkFun AS7262 Visible Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7262 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board --- simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic Shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
-
product
AC/DC Current Probe, 100 MHz, 15A
N2893A
The Keysight N2893A is a 100 MHz bandwidth, active current probe for InfiniiVision and Infiniium oscilloscopes. The probe features flat bandwidth (DC-100MHz), low noise(<2.5 mA rms) and low circuit insertion loss. Auto demagnetization (degauss) and calibration removes any residual magnetism and unwanted DC offset in the probe. The probe is powered directly by the InfiniiVision and Infiniium Autoprobe interface, eliminating the need for an additional power supply.
-
product
Logic Analyzer
Ant18e
The Ant18e logic analyzer is compact, easy to use, powerful, and inexpensive. The Ant18e features high speed data acquisition, state (synchronous) and timing (asynchronous) acquisition modes, Trigger-In and Trigger-Out connections, and a user-level programming interface.
-
product
Single Mode Low Loss All Optical Switch From 8x8 To 192x192 Ports
SERIES 6000
The Polatis Series 6000 Network Optical Switch is a high-performance, fully non-blocking all-optical matrix switch available in sizes from 8x8 up to 192x192. It is designed to meet the highest performance and reliability needs of the most demanding applications with exceptionally low optical loss, compact size, low power requirements and fast switching speeds. With support of Software-Defined Networks (SDNs) via an embedded NETCONF and RESTCONF control interfaces, the Series 6000 enables extreme...show more -
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends
A050DM5-T-0A200
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Signal Conditioners & Interface
Modbus RTU Remote Connectivity and Control. Minimize Long Cable Runs with Modbus Network. Pulse to Frequency Conversion. Shaft Speed Pulse to DeviceNet. Shaft Speed Pulse to 4-20 mA Conversion.Sensor Compatibility
-
product
2-port/4-port GigE PCI Express Card
AX92322
The AX92322 is a GigE compliant PCI Express card supporting two or four independent Gigabit Ethernet ports. It features PCI Express x4 interface and has four powerful independent Intel® Ethernet Controller i210-AT. The GigE frame grabber card supports 9.5KB Jumbo Frame and IEEE 1588 to enable faster and more accurate throughput of data. The AX92322 is built for machine vision and surveillance applications in industrial IoT field. This PCI Express frame grabber card is designed to help customers ...show more -
product
2MP Stereo Camera for NVIDIA® Jetson Nano™/AGX Xavier™/TX2
STEEReoCAM™
Houses two OmniVision's 1/2.9" OV2311 Monochrome image sensorHigh-speed 2-lane MIPI CSI-2 interface to connect with the Host ProcessorPlugs in to NVIDIA® Jetson Nano™/AGX Xavier™/TX2 developer kit2MP Global Shutter Sensor10-bit Monochrome output formatHouses 6-axis Inertial Measurement Unit (IMU)Baseline distance of 100mmAccurate depth sensing with a flexible range between 0.95m to 8mS-mount lens holder (M12) with pre-calibrated S-mount lens pairSupport Multiple SteereoCam to a Single board
-
product
COM Express Type 6
The COM Express Type 6 modules are designed with all components necessary and offer the most updated bus interfaces. The COM Express modules satisfy a wide range of vertical embedded applications with features of great computing performance and rich I/O capabilities, and reduce customers' time-to-market and ownership cost.
-
product
6-Ch 200 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 58621
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Six 200 MHz 16-bit A/Ds- Six multiband DDCs (digital downconverters)- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Two multiboard programmable beamformers- 4 GB of DDR3 SDRAM; 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
50 Ohm BNC to BNC Cable Assembly
40-977-501-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Intel® Processor N Series And Atom® X Series Expandable, Cost-Efficient Modular Industrial Computers
MXC-330
Intel® latest ADL-N cost-performance embedded Fanless system, DDR5 SO-DIMM, various IO interface for different industrial applications, including Isolation COM port & DIO, 4x GbE LAN, M.2 expansion slot for general application.
-
product
0-10V Load Cell Amplifier
Type 132
The Type 132 Amplifier is designed to amplify the signal from any load cell with full bridge connection, allowing the user to use the data from the load cell in a more efficient and productive way.The Type 132 Amplifier is designed to interface to a full bridge strain gauge based load cell or similar sensor. It can be calibrated to provide a 0-10V output for a fixed load range from the sensor.
-
product
1.5 GHz, 1.0 pF Active Differential probe
ZD1500
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
product
4-port/8-port USB 3.0 PCI Express Card With 4 Independent Host Controllers
AX92321
*Four or eight USB 3.0 ports*Four independent USB 3.0 host controllers*900 mA/1500 mA max. per port configurable via jumper settings*Compliant with USB 3.0 Rev.1.0 and Intel® xHCI Rev.1.0*PCI Express x4 interface*Operating temperature from 0˚C to 70°C*Supports Windows® 7/10*Supports each port’s power on/off via software settings
-
product
CAN/LIN Interfaces - 2 Channel PCIe
OTP2 module no053
Expand your test system with the high-speed interface of the OTP2 module no053. The extension of the module can create new possibilities for your test system.
-
product
RF Downconverters
SignalCore offers traditional multi-stage and single-stage RF downconverters, and Direct IQ demodulators that feature low phase noise, high dynamic range, wide bandwidth, and continuous tuning. SignalCore RF downconverters are compact and built for mechanical robustness and ruggedness. Applications include various test and measurement applications such as those in spectral monitoring, signal intelligence, ATE, and software-defined radio. All products are provided with a Graphical User Interface (GUI), driver, and API for easy programming control.
