Showing results: 76 - 90 of 167 items found.
-
MRU-200 -
Sonel S.A.
MRU-200 is the only meter in the market which uses all measurement methods.Possible measurements:- earth resistance measurment with 2-pole, 3-pole,4-pole method,- impulse earth resistance measurement, two kinds of measuring impulse 4/10s, 10/350s,- earth resistance measurement without disconnecting measured earths (using clamp),
-
CF106 -
Calmet Smart Calibration Devices
Universal miniature scanning head for detecting (counting) impulses from inductive, LED and LCD energy meters. Additionally it enables counting of manually triggered impulses (Start/Stop push button function). Sometimes (when access is difficult) it is the only way to count pulses from inductive, LED and LCD meters.
-
IDS Innomic GmbH
Industrial sensors, miniature sensors, triaxial sensors, special sensors, measuring microphones, impulse hammer.
-
Precision Acoustics LTD
PVdF transducers have a wide bandwidth, short impulse response and can be designed to your specific requirement.
-
MIG0612T-K12 -
EMC Partner AG
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
MIG0624T-K12 -
EMC Partner AG
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
EFT coupling -
Langer EMV-Technik GmbH
s used for direct-contact measurements of impulse immunity in IC pins, according to IEC 62215-3 and IEC 61000-4-4.
-
SGFS -
Shanghai Jiuzhi Electric Co., Ltd.
The multiple chopping gap is used to chop lightning impulses on the front and/or on the tail.The multiple chopping gap serves simultaneously as a load capacitor for the impulse generator and allows excellent reproducibility of the chopping time and does not distort the wave shape until the chopping point.The sphere distance is automatically adjusted and operated by the controls of SG2010 and SG2011. A manual control box is available as well.
-
Sonelastic -
ATCP Physical Engineering
Sonelastic® is a line of solutions for nondestructive characterization of elastic modulus and damping of materials by the natural frequencies obtained by impulse excitation technique.
-
2654-1 -
Solar Electronics Company
The Solar Model 2654-1 Lightning Generator synthesizes electrical impulses needed for testing susceptibility to transients induced in aircraft equipment by lightning strikes.
-
MIG0603CAP -
EMC Partner AG
The MIG0603CAP consists of two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape 1,2/50 µs and are combined in a 4 unit height 19" rack. The generator circuits are defined in IEC 60384-14 and EN 132400. The serial resistors Rs, the impulse capacitor CT, and the load capacitance Cp will be automatically switched when different capacitance ranges are selected on the MIG0603CAP.
-
2291 -
Georg Fischer Signet
The 2291 Guided Wave Radar level transmitter is designed for continuous level measuring of conductive or non-conductive liquids, pulps and solids. The 2291 level gauge operates based on the well-known TDR (Time Domain Reflectometry) principle. Micropulses are sent along a probe guide at the speed of light. As soon as the impulse reaches the surface of the medium, it is reflected back to the electronic module. Level distance is directly proportional to the flight time of the impulse.
-
SGS H & SGS V -
Shanghai Jiuzhi Electric Co., Ltd.
The sphere gap type SGS H or SGS V can be used for Impulse, AC and DC voltage calibration according to the IEC 60052 recommendation.The spheres are arranged vertically or horizontally, one being mobile. In the vertical version the mobile sphere is remotely adjusted by using an electrical drive. In the horizontal version, both spheres are mounted on columns of insulating materials, hence enabling to superimpose impulse AC and DC voltages.
-
HIGHVOLT Prüftechnik Dresden GmbH
Designed for the measurement of alternating current (AC), direct current (DC), lightning (LI) and switching (SI) impulse high voltages (HV) as well as AC and impulse high current (HC) according to IEC 60060, IEC 61083 and IEC 60052, available as indoor and outdoor design.
-
Model 19032/19032-P -
Chroma ATE Inc.
Electrical Safety Test (EST) Analyzer that combines the functions of impulse test, hipot, insulation resistance and DC resistance measurements. It has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement that can comply with the wound components test demands by providing maximum 10 channels output for multichannel scanning tests to save time and labor costs.