Showing results: 301 - 315 of 2549 items found.
-
GX5292e -
Terotest Systems Ltd.
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
PCIe-DIO-24HS -
Acces I/O Products, Inc.
This product is a x1 lane PCI Express digital I/O board available in two models. The PCIe-DIO-24H is the basic DIO and the PCI-DIO-24HS features advanced change-of-state (COS) detection capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
68G5P -
North Atlantic Industries
The 68G5P is a 3U OpenVPX board that can be configured with up to three NAI smart I/O and communication function modules. Uniquely designed, the 68G5P provides external access via PCIe x1 and/or SATA II interfaces directly to supported NAI function modules, providing external host SBC function expansion. Additionally, the 68G5P is on NAI’s certifiable product line development roadmap supporting DO-178C and DO-254 design assurance guidelines for safety-critical applications. Ideally suited for rugged Mil-Aero applications, the 68G5P delivers off-the-shelf solutions that accelerate
-
GX3500 -
Terotest Systems Ltd.
The GX3500 is a user configurable 3U FPGA PXI card which offers 160 digital I/O signals for specific application needs. The card employs the Altera Cyclone III FPGA which can support clock rates up to 150 MHz and features over 55,000 logic elements and 2.34 Mb of memory. The 3U PXI FPGA card GX3500 can also accept an expansion card assembly which can be used to customize the interface to the UUT – eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system.
-
DIOEasy -
Marvin Test Solutions, Inc.
DIOEasy offers test engineers an efficient tool for developing, debugging, and executing digital test vectors for Marvin Test Solutions' GX5050 series, GX5150 series, GX5280 series and GX5291, GX5292, GX5293 and GX5295 dynamic digital instruments.Digital I/O (DIO) systems are very complex and typically require a substantial amount of programming effort to define data vectors. In order to simplify vector development, Marvin Test Solutions developed Windows-based DIOEasy, providing users with an easy to use interface. Toolbars and menus provide quick access to vector editing and viewing tools.
-
NI
PXI Multifunction Reconfigurable I/O Modules feature a dedicated analog-to-digital converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. You can customize these models with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop (HIL) testing, custom protocol communication, sensor simulation, and high-speed control. PXI Express models also include peer-to-peer streaming for direct data transfer to other PXI Express models.
-
Pacific Instruments, Inc.
Series 6000 analog I/O modules condition, amplify, filter and digitize signals from virtually any transducer. All modules have conditioning & amplifier per channel and nearly all modules allow for setting bridge completion, shunt calibration, transducer power, gain, etc. individually per channel. Following the conditioning/amplifier stage, multi-pole Bessel or Butterworth analog filters are provided on each channel and can be set or bypassed individually by program control. A number of the modules include a high level analog output providing a conditioned/filtered output to a redundant, external A/D system. A 16-Bit Successive Approximation A/D follows the analog filter stage. Some modules use a single A/D with sample and hold while others have an A/D per channel. Sample rates are programmable per channel to easily accommodate mixing high and low speed measurements into a single data stream. Programmable hardware based warnings and alarms are included in the channel-by-channel architecture and are detected by digital output modules in the system, providing an ultra-low latency control capability directly from the data acquisition system.
-
ViTec Co. Ltd
The plug-in chassis provides connectivity for I / O modules. The chassis core is an FPGA for reconfigurable I / O signals. Chassis are available in various configurations and are designed to accommodate 4 or 8 C-series modules.
-
IP-EP200 -
Acromag, Inc.
This series of plug-in mezzanine modules provides a user-customizable Altera® Cyclone II FPGA on an Industry Pack (IP) module. The module allows users to develop and store their own instruction set in the FPGA for adaptive computing applications.
-
GX3232 -
Terotest Systems Ltd.
The GX3232 is a multi-channel 16-bit, analog input and output cPCI module, supporting 32 single-ended or 16 differential input channels and four analog output channels. The inputs can be software configured for differential or single-end operation and are sequentially scanned with a maximum aggregate scan rate of 300 kS/s. Three input ranges are software-selectable: ±10 V, ±5 V or ±2.5 V. Optionally, the GX3232 is available with a high voltage input configuration and supports three ranges: ±60 V, ±30 V and ±15 V.
-
Axiomtek Co., Ltd.
Axiomtek develops a full spectrum of machine vision cards to help customers accelerating their design and reducing development costs.
-
Computer Conversions Corporation
The Computer Conversions Corporation XMC Series Cards can be used in a wide variety of test, data acquisition, simulation, and control applications.
-
Neousys Nuvis -
ViTec Co. Ltd
Nuvis-5306RT , Nuvis-534RT, Nuvis-7306RT contain interfaces for connecting to all necessary devices: LED lighting controller, camera trigger, encoder input, PWM output and digital I / O lines.- Intel® 7th Gen Core ™ i7 / i5 65W / 35W, up to 32GB DDR4- Built-in I / O- 4-CH CC / CV backlight controller- 4-CH trigger camera- 1-CH quadrature encoder input- 8-CH isolated DI and 8-CH isolated DO- Built-in camera interfaces- 4-CH IEEE 802.3at Gigabit PoE + ports- 4-CH USB 3.1 Gen1 ports- NVIDIA 75W GPU Support
-
HR-4P -
Hall Research Inc.
The Model HR-4P is a programmable RS-232 device designed for control & automation of a Projector, LCD, or any other device with serial or IR port.
-
Bridgenorth Signal Processing
PCI, cPCI / PXI : 32 / 64 bit, 33MHz6711 or 6713 DSP32MB SDRAMLow latency burst interfacesHigh data transfer ratesGreat trigger flexibilityMultiboard support