Showing results: 1 - 15 of 23 items found.
-
7415-3 -
Solar Electronics Company
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
156166-01 -
NI
SHC68-C68-RDIO2 Shielded R Series High Speed Digital Male VHDCI Cable, 1m
-
156166-02 -
NI
SHC68-C68-RDIO2 Shielded R Series High Speed Digital Male VHDCI Cable, 2m
-
191667-01 -
NI
68-Pin Male VHDCI to 68-Pin Female D-SUB, Shielded Digital Cable 1m
-
Trig-TekTM 550D -
Astronics Corporation
Two channels with variable high pass and low pass filters in a module 7" high x 2.6" wide
-
SR600 -
Stanford Research Systems, Inc.
The SR600 series consists of three dual-channel instruments. Each instrument channel has a low-noise preamplifier, a precision high pass or low pass filter section, and an output amplifier. The filters are 8-pole, 6-zero elliptic-type with 115 dB per octave rolloff, 0.1 dB of passband ripple, and 80 dB of stopband attenuation.
-
Fairview Microwave Inc.
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
J2190A -
PICOTEST Corp.
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
Smiths Interconnect
Filter connector series includes EMI/ EMP/ESD circular, ARINC, D-subminiature and micro-D connector styles. They can be combined with high energy TVS diode technology to achieve lightning and EMP transient protection. Smiths Interconnect's EMI filter connectors use multi-layer ceramic capacitor arrays together with inductive materials to realize robust, high performance low pass filter networks. Where required, transient protection can be combined with EMI /RFI filtering to provide maximum protection. The diodes as well as the EMI filter are packaged separately so the construction of the connector remains modular.
-
TBFL1 -
TekBox Singapore Pte. Ltd.
The TBFL1 is a combined transient limiter / attenuator / high pass filter, designed to provide optimum protection of spectrum analyzer or measurement receiver inputs when carrying out conducted noise measurements or other measurements where the input levels cannot be predicted with certainty or where accidental overloads may occur.
-
Ducommun Inc
Ducommun millimeter wave products include various passive components including multi-hole directional couplers (PCM), crossguide couplers (PCC), magic tees (PCT), coax power dividers (PPD), bandpass, low pass and high pass filters (PFB, PFL and PFH), waveguide diplexers (PDC), waveguide transitions (PRC and PTW), waveguide to coax adapters (PTC) and waveguide components (PWS, PWE, PWH, PWM and PWT). These passive components cover frequency range from 8.2 to 110 GHz and feature high performance and low cost.
-
OADM-1000 (100GHz) -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OADM-1000 100GHz optical add/drop multiplexer based on the mature thin-film filter technology, metal seal. With so much great features like low insertion loss, high isolation, wide pass band, flexible configuration and so on. This is the ideal parts for used in DWDM system Add/Drop special wavelength.
-
Model 1122 / 1122X -
Aplab Limited
- Wide Frequency Range 0.2Hz to 1.3GHz- 2 Separate Channels, for LOW & HIGH Frequencies- High Sensitivity- 8 Digit Green LED Display- Microcontroller based Advance Technology- Optional RS232 Interface- Reciprocal Counting Technique for High Resolution at Low Frequency- Period Measurement- Low Pass Filter for Noisy Low Frequency (<100KHz)- 4 Selectable Gates (10ms, 100ms, 1sec, 10sec)
-
GX2482 -
Marvin Test Solutions, Inc.
The GX2482 series are a high performance, dual differential channel, 16-bit digitizer offering high dynamic range and excellent SFDR. The module’s differential inputs, coupled with its low distortion makes it an ideal instrument for analyzing high performance or low level analog signals. Each channel offers 3 selectable low pass filters, a 16 bit, 180 MS/s ADC, and 64 M words of memory for each channel.
-
Com-Power Corporation
Transient limiter LIT-153A and LIT-930A protects a spectrum analyzer input from high-level transients from the line impedance stabilization networks during EMC conducted emissions testing. It has a combined frequency range of 9 kHz to 30 MHz. The built in high pass filter helps reduce 50/60 Hz line feed through. (see application notes)