Showing results: 61 - 75 of 121 items found.
-
LCC-900 -
OptCom Company, Ltd
Screens the pass/fail results or module type LED image information that is automatically reset via data transfer with handler unit. Data results are stored in server for unified management.
-
FTI 1000 -
Focused Test, Inc.
The FTI 1000 tester consists of independent test channels that allow all DC and AC MOSFET parameters to be tested either separately, or in one handler insertion or prober touch-down.
-
3000B -
Exatron Inc.
Exatron's Model 3000B Series of automatic component handlers integrates customer-specific ambient temperature programming and/or test sites and up to eight automatic device inputs and outputs.
-
U9405A -
Keysight Technologies
Unlike traditional bridge type board handlers that add a 3rd party equipment on your offline ICT systems, we provide a one-stop shopping experience when you are automating your in-circuit test.
-
PET-2/PET-3 -
Exatron Inc.
Exatron's Prototype Engineering Test (PET) Fixture is a semi-automated solution that bridges the gap between a fully automated handling system and a low cost, lower volume handler.
-
AN133 -
6TL Engineering
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Virginia Panel Corporation
The iDock Series is a series of connectors ideal for use with automatic machine handlers in production testing. Their floating bushings allow up to .04" of re-alignment. Use them with a mix of I/O modules and use up to 5,952 signal contacts simultaneously. The iDock series is rated at 100,000 cycles.
-
Virginia Panel Corporation
The iDock Series is a series of connectors ideal for use with automatic machine handlers in production testing. Their floating bushings allow up to .04" of re-alignment. Use them with a mix of I/O modules and use up to 5,952 signal contacts simultaneously. The iDock series is rated at 100,000 cycles.
-
D25 -
Virginia Panel Corporation
iDock Series connectors are a Mass Interconnect for use with automatic machine handlers. The D25 is capable of mating a wide variety of I/O module configurations, and can engage up to 5,952 signal contacts. All iDock Series connectors are compatible with VPC's existing line of modules, contacts, and tools.
-
D12 -
Virginia Panel Corporation
iDock Series connectors are a Mass Interconnect for use with automatic machine handlers. The D12 is capable of mating a wide variety of I/O module configurations, and can engage up to 2,880 signal contacts. All iDock Series connectors are compatible with VPC's existing line of modules, contacts, and tools.
-
GPR-GB7SY -
Genmark Automation
The GPR-GB7SY Yaw-Axis (single and dual yaw) robot features Genmark’s technologically advanced mechanisms including patented GPR and YAW technologies to achieve the highest level of performance currently available in an automated material handler capable of transporting up to 450mm wafer payloads with utmost reliability and precision.
-
D3/D4 -
Virginia Panel Corporation
iDock Series connectors are a Mass InterConnect for use with automatic machine handlers. The D3/D4 connector is capable of mating a wide variety of I/O module configurations, and can engage up to 672 signal contacts. All iDock Series connectors are compatible with VPC's existing line of modules, contacts, and tools.
-
UWE Electronics
For handler setup or hand test, a manual lid is often required as part of the test hardware set. We have refined our standard offerings so that with each socket you can receive a lid designed specifically for your application from one of five standard lid form factors
-
NLINE-T1553 -
Alta Data Technologies LLC
Supports Full Real-Time Control the Same as a PCI Express Card in a Server! Much Better than a non-real-time USB.Full Hardware Interrupt Handler Support! AltaAPI SDK Provides Easy Integration – Use the exact same code as other Alta PCIe devices! Windows 10 Support Only
-
LTX-Credence
Easy docking and undocking of the MEMS modules to the standard test handler whether Gravity, Pick and Place or Test in StripTest in the complete tri-temp range for ambient, hot and cold (automotive certified)Easily convertible to other packagesDownscaled stand-alone engineering set-up availableGlobal support by experienced Cohu Field Service and Applications staff