Showing results: 166 - 180 of 208 items found.
-
Model 8800P -
Teledyne Analytical Instruments
The 8800 series uses field proven aluminum oxide (Al2O3) sensing technology to accurately detect trace moisture on either a continuous or spot checking basis. All Al2O3 sensors share the same basic operating principle: the capacitance measured between the sensor’s aluminum core and gold film deposited on the oxide layer varies with the water content. The 8800 series moisture sensor employs unique Hyper Thin Film (HTF) technology, which offers three major structural improvements in Al2O3 sensor design. These structural changes, noted below, provide the user with increased sensitivity, greater stability and a quicker response time when compared to other conventional aluminum oxide sensors on the market today.
-
Model 8800T -
Teledyne Analytical Instruments
The 8800 series uses field proven aluminum oxide (Al2O3) sensing technology to accurately detect trace moisture on either a continuous or spot checking basis. All Al2O3 sensors share the same basic operating principle: the capacitance measured between the sensor’s aluminum core and gold film deposited on the oxide layer varies with the water content. The 8800 series moisture sensor employs unique Hyper Thin Film (HTF) technology, which offers three major structural improvements in Al2O3 sensor design. These structural changes, noted below, provide the user with increased sensitivity, greater stability and a quicker response time when compared to other conventional aluminum oxide sensors on the market today.
-
NZXT HALE90 850w -
Rexus Corp.
*80+ Gold certified: The HALE 90 series from NZXT operates atultra high efficiency, at 20%, 50% and 100% loads, efficiencies are87%, 90%, and 87% respectively.*Single140mm two ball-bearing fan operates with minimal noiseeven at full load. Maximum decibel levels are 20db for wattagesbetween 550-750W and 30db for 850W and above.*Strong Single Rail Design: A single +12V rail provides stabilityand ease of use making the most out of your power supply. Offers stable & clean current delivery under heavy load.*Modular cable design: Modular cable design allows the user topick and choose which cables they want to use, optimizing cablemanagement and airflow inside the chassis. Flat cables allow for easier routing and bending inside the computer chassis during wire management.
-
NZXT HALE90 1000w -
Rexus Corp.
*80+ Gold certified: The HALE 90 series from NZXT operates atultra high efficiency, at 20%, 50% and 100% loads, efficiencies are87%, 90%, and 87% respectively.*Single140mm two ball-bearing fan operates with minimal noiseeven at full load. Maximum decibel levels are 20db for wattagesbetween 550-750W and 30db for 850W and above.*Strong Single Rail Design: A single +12V rail provides stabilityand ease of use making the most out of your power supply. Offers stable & clean current delivery under heavy load.*Modular cable design: Modular cable design allows the user topick and choose which cables they want to use, optimizing cablemanagement and airflow inside the chassis. Flat cables allow for easier routing and bending inside the computer chassis during wire management.
-
Talon RTR 2757 -
Pentek, Inc.
- Designed for data capture from Pentek Quartz® RFSoC products' 100 Gigabit Ethernet ports- Single QSFP28 port with MPO transceiver- Real-time record rates up to 12.5 GB/s (100 Gigabits/s)- Front-panel removable solid state storage up to 122 TB- Dual Intel Xeon® Gold processors with up to 4 TB of DDR4 SDRAM- 4U 19-inch industrial grade server chassis- Supports up to four independent UDP streams- SystemFlow software GUI with Signal Viewer analysis tool- C-callable API for integration
-
400C Series -
CH Instruments, Inc.
The quartz crystal microbalance (QCM) is a variant of acoustic wave microsensors that are capable of ultrasensitive mass measurements. Under favorable conditions, a typical QCM can measure a mass change of 0.1-1 ng/cm2. QCM oscillates in a mechanically resonant shear mode under the influence of a high frequency AC electric field which is applied across the thickness of the crystal. Figure 1b below shows an edge view of a QCM crystal undergoing oscillatory shear distortion. The central portions of the top and bottom of the crystal are coated with a typically disk-shaped thin metal film (e.g., gold).
-
ESI Technology Ltd
ESI Technology manufacture a wide range of pressure sensors using a variety of different technologies. Pressure transducers (voltage output), pressure transmitters (milliamp output), panel meters, accessories. Silicon-on-Sapphire technology and a titanium diaphragm combine to make the new Gold Standard in pressure sensing. Custom pressure measurement solutions have been integral to ESI’s success. All aspects of design and manufacture are done in-house at our UK facility. Impressive quality at an affordable price. So if you don’t see what you are looking for, just ask.
-
Model T300U -
Teledyne Advanced Pollution Instrumentation
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.
-
Model T200U NOY -
Teledyne Advanced Pollution Instrumentation
The Model T200U NOy analyzer has been developed and refined specifically to address the challenges of NOy monitoring as required, for example, in the US NCore network. It uses the proven chemiluminescence principle and is coupled with a remote NOy converter via umbilical to allow measurements with a lower detectable limit of 50 ppt.The Model T200U NOy analyzer combines a gold plated reaction cell with an enhanced performance pump, special low noise photomultiplier tube, and unique signal conditioning to provide exceptional sensitivity. In addition, a pre-reactor separates the NO-O3 reaction from background chemiluminescence to allow accurate auto-zero of the analyzer. The remote NOy converter is provided with a stainless steel, NEMA 4X (IP65) enclosure and custom sample umbilical to allow a mounting height of 10 meters. In addition, the converter features a unique purge circuit designed to remove residual calibration gas.
-
Pasternack Enterprises, Inc.
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
Pasternack Enterprises, Inc.
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
UPG-07 Monochrome -
Danatronics Corporation
PG-07 Series of hand held ultrasonic precision gages are available in 4 models. Our UPG-07 series is the ideal unit to non-destructively test the wall thickness for manufactured parts requiring unprecedented accuracy and resolution. The UPG-07 series utilizes single element transducers and offers a 30 Mhz, square wave pulser, .0001" or 1 micron resolution with the ability to store and re-call 30 unique applications. So if you are measuring light bulbs, plastic bottles, golf clubs, coil steel, thin aluminum, aircraft parts and even pure gold bars, the UPG-07 series is the right choice.
-
Real Time Ice Thickness Measurement -
Sensors and Software Inc.
The IceMap real-time display shows the automatically detected bottom of the ice (blue line) in real time. Users can set a minimum thickness warning threshold (gold line). Winter ice roads and bridges are a common transportation link in the northern regions of Canada, Alaska, Europe and Russia. The Sensors & Software IceMap system is designed to measure the ice thickness on these temporary, yet vital, links and ensure the safety of all travelers. The GPR sensor is towed across the ice surface behind a truck or snowmobile and the ice thickness data, displayed in real-time as a cross-sectional image, are sent wirelessly to the operator’s computer.
-
RFCT -
Textron Systems
Textron Systems’ Radio Frequency Cable Tester (RFCT) allows for on-site testing and maintenance for radio frequency (RF) transmission paths within a platform. Using preconfigured databases of sweep parameters and pass/fail criteria, the RFCT quickly determines the status of installed RF cables. The RFCT checks each cable’s performance characteristics to include voltage standing wave ratio (VSWR), insertion loss (IL), phase and phase matching. If a cable fails a test, the RFCT automatically determines the distance-to-fault (DTF). With its intuitive touchscreen-based user interface and lightweight, ruggedized packaging, the RFCT is the gold standard for operational-level RF cable testing.
-
SCHILLER AUTOMATION GmbH & Co. KG
The Standard SD Express Memory Card Test Adapters support PCIe® 16 GT/s (Gen4) and PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD8.0 and SD7.1. Minimal crosstalk, short trace lengths. The Micro SD Express Memory Card Test Adapters supports PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD7.1. Minimal crosstalk, short trace lengths. They all support SDHC, SDXC, and SDUC operation modes Data collection via Lab Standard SSMP Test Cables and hard gold mating surface allow for high cycle count insertions and reliable performance.
