Showing results: 2461 - 2475 of 2943 items found.
-
L8990M Series -
Keysight Technologies
Keysight’s L8990M Modular Switch Matrices provide a cost effective and quick ship solution with a simple and flexible platform for basic RF switching. The L8990M can support up to 30 switch channels in a 2U rack-mountable enclosure with signal frequencies up to 67 GHz. It can support up to 66 switch channels in a 4U high enclosure. This provides the capability to test a wide range of RF and telecommunication products and devices.
-
Keysight Technologies
Generate trusted microwave signals: get metrology-grade frequency & level accuracy with excellent distortion & spurious characteristicsRely on the highest quality signals from pure CW tones with 1 W of power to complex, vector-modulated signals with 4 GHz bandwidthReduce the time you spend on signal creation with Signal Studio softwareTake advantage of increased performance, flexibility & speed when you replace a legacy source with the code-compatible PSG
-
M9703B -
Keysight Technologies
Based on the AXIe standard the M9703B is an 8-channel, 12-bit digitizer/wideband digital receiver, able to capture signals from DC up to 2 GHz at 1.6 GS/s. A channel interleaving capability allows waveform acquisition at up to 3.2 GS/s with exceptional measurement accuracy. The M9703B also provides real-time data processing, large FPGA and customizable I/O interfaces. Detailed explanations can be found in the firmware options section of the datasheet.
-
8480 Series -
Keysight Technologies
The 8480 thermocouple and diode power sensors series provide extraordinary accuracy, stability, and SWR over a wide range of frequencies and power levels.50 dB dynamic range (maximum) over –70 to +44 dBmFrequency range from 100 kHz to 110 GHz (sensor dependent)Accurate average power measurementsRange of thermocouple and diode power sensorsCompatible with EPM, EPM-P, P-series, and E1416A power meters
-
PCD 8250 -
Seibersdorf Labor GmbH
Exposure evaluation next to mobile communication facilities e.g. GSM and UMTS base stations. Accurate RF radiation safety measurements e.g. nearby broadcast stations or in buildings. All kinds of field strength measurements where high precision, a wide frequency range and small antenna dimensions are required. Measurements according to our Field Nose method. Frequency range: 80 MHz 3 GHz
-
M9316A -
Keysight Technologies
The M9316A PXIe Vector Modulator is a 3-slot module with integrated wideband IQ modulator and arbitrary waveform generator (AWG) designed to work with the M9383A PXIe Microwave Signal Generator. When ordered with M9383A, it can support 1MHz to 20 GHz frequency coverage, up to 160 MHz RF bandwidth, and up to 1 Giga-sample of AWG playback memory. (See M9383A PXIe Microwave Signal Generator options.
-
ZVA-Z Series -
Radiometer Physics GmbH
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
TS8997 -
Rohde & Schwarz GmbH & Co. KG
The R&S®OSP-B157W8 PLUS 7.5 GHz module with up to eight channels is the core of the system and uses a printed RF switch board in solid-state relay (SSR) architecture. It allows flexible operation of the connected DUT (up to eight ports) for power measurements, signal conditioning via the integrated attenuators, couplers and combiners, RF switching to the measuring instruments in combination with the R&S®OSP-B157WX up to 40 GHz and is controlled by R&S®WMS32 software.
-
Schwarzbeck Mess Elektronik
Tuned half-wave dipoles have been among the most important antennas from thebeginning of rf-technique. The characteristics of half-wave dipoles havebeen calculable very early using the Maxwell and Hertz equations. Therefore the halfwave dipole became a reference antenna. The ideal (lossless) half-wave dipole has anisotropic gain of 2.15 dBi and an impedance of 73 Ohm. The directional pattern is circular inthe H-plane, "8-shaped" in the E-plane with the maxima perpendicular on the dipole axis.The half-power beamwidth (-3 dB) is approx. 78°. The impedance of real dipoles isdepending on the thickness/length ratio of its elements, typical values are 60-70 Ohm.Dipoles for industrial applications are available in the frequency range from 30MHz to up to approx. 4 GHz. The dipole elements are length variable (telescopic) orwith fixed length, the latter especially above 1 GHz. The most important applications aretest site evaluations (NSA, normalized site attenuation) and the determination of ERP(Effective Radiated Power) respectively EIRP (Effective Isotropic Radiated Power).
-
DIO2 -
APPLICOS
The DIO-II module is a multimode digital source and capture unit. In Low Speed Mode it provides a 20-bit parallel or 24-bit serial I/O capability running at speeds up to 50 MHz. In High Speed Mode, the DIO-II provides a 16-bit parallel I/O capability up to 200 MHz. In both Modes, the Clock is generated by a low jitter PLL source that is capable of generating clocks from 320 kHz up to 1 GHz.
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless GPS Signal Splitters are available in 2-way thru 48-way configurations spanning 1-2 GHz with unpeered performance in GPS (L1-L5), GNSS, Galileo, GLONASS, BeiDou, and IRNSS antenna splitting applications. The 200 ohm internal load on the DC-blocked port(s) prevents receivers from incorrectly sensing an antenna fault when there is no current draw. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
Fairview Microwave Inc.
Fairview Microwave’s high-speed end launch connectors are comprised of four models that provide VSWR as low as 1.10:1 and a maximum operating frequency of 40 to 110 GHz, depending on the model. These end launch connectors are reusable, don’t require any soldering and have a compact profile with a 0.350-inch mounting width and a 0.005-inch launch pin. They feature an outer conductor made of stainless steel and a gold-plated beryllium copper center contact.
-
Talos-3012 -
ADLINK Technology Inc.
The ADLINK Talos-3012 EtherCAT master controller, based on the Intel Atom quad-core processor E3845 1.9 GHz, with IEC-61131-3 compliant syntaxes, delivers reliable control for multiple axes and versatile I/O control supporting specialized real-time applications. The Talos-3012 supports up to 64-axis motion control and 30K points within determined cycle times, and is verified for interoperability with various EtherCAT servo drives and 3rd party EtherCAT products.
-
U5303A -
Acqiris SA
The U5303A is a two channel PCIe 12-bit signal acquisition card with programmable on-board processing. This ADC card occupies a single full-length PCIe slot of the host PC and captures signals on 2 channels, from DC to 2 GHz at 1 GS/s, 1.6 GS/s or 2 GS/s. Featuring DDR3 acquisition memory up to 4 GB, this digitizer includes a Xilinx FPGA allowing the implementation of custom real-time processing algorithms.
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's high efficiency linear power amplifiers are available for operating frequencies from 1MHz to1 GHz with output power from 1 to 100 watts. Combined with linear design, these linear power amplifiers provide ultra low distortion, suitable for multi-band, multi-mode communication applications. With built-in monitor circuits, Keylink's power amplifier assure consistent performance in terms of reliability. KeyLink's linear power amplifiers can be categorized as follows:
