Showing results: 1066 - 1080 of 4162 items found.
-
PGA 1240 -
Schlöder GmbH
The power generator PGA 1240 is suitable for EMC testing in accordance with standard IEC / EN 61000-4-16 in the frequency range from DC to 300 kHz.
-
SRO-100 -
VREMYA-CH JS Company
Rubidium generators SRO-100 are designed to generate and output to the consumer highly stable, high-frequency, spectrally pure sinusoidal signals with a frequency of 5 or 10 or 15 MHz.
-
DIRANA -
OMICRON electronics
DIRANA uses dielectric frequency response (DFR) analysis in order to determine the condition of high-voltage insulation systems such as those in power transformers, bushings, cables and generators.
-
ESDEMC Technology LLC
Microwave Absorbing Material Characterization System that measures the signal loss through a material sample in a frequency range of 5 15GHz (with the option of extension to lower frequencies).
-
all-sun
is a multifunction calibrator-tester, to be used primarily as a standard for calibration laboratories. It can be used for calibration of any measuring instrument which measures voltage, current, resistance, capacitance and frequency.
-
W281D -
Keysight Technologies
The Keysight W281D is a 1-mm male to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281D is used with the Keysight 8510XF systems.
-
W8486A -
Keysight Technologies
The W8486A waveguide power sensor measures average power over the frequency range 75 GHz to 110 GHz and power range -30 to +20 dBm.
-
S96084B -
Keysight Technologies
Enables accurate measurement of relative phase and absolute group delay of a frequency converter with a built-in LO source, without having to access a common reference signal
-
V281D -
Keysight Technologies
The Keysight V281D is a 1-mm male to V-band waveguide adapter with a frequency range of 50 GHz to 75 GHz. The Keysight V281D is used with the Keysight 8510XF systems.
-
W281C -
Keysight Technologies
The Keysight W281C is a 1-mm female to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281C is used with the Keysight 8510XF systems.
-
V8486A -
Keysight Technologies
The V8486A waveguide power sensor measures average power over the frequency range 50 GHz to 75 GHz and power range -30 to +20 dBm.
-
Analog Devices Inc.
It is often beneficial to use a video driver at the output of a video encoder for power savings, line driving, and additional circuit protection. The video driver is typically configured as an active filter, also known as a reconstruction or anti-imaging filter. The purpose of the reconstruction filter is twofold: it blocks the higher frequency components (above the Nyquist frequency) that were introduced into the video signal as part of the digitization process and provides gain to drive the external 75 Ω cable to the video display.
-
PFM3000 -
Aim-TTi
3 Hz to 3000 MHz in two overlapping rangesHigh input sensitivity over the full frequency rangeHigh impedance measurement up to 125 MHzReciprocal counting technique gives superior resolutionPeriod measurement from 3 Hz to 125 MHzBattery operation and lightweight, handheld formatPush-to-measure function with auto power-downLarge 8+ digit display with full range of annunciatorsSelectable measurement time; display hold functionNoise filter for low frequency measurements
-
TM-4D -
Spectrum Instruments, Inc.
The Intelligent Reference/TM-4D™ breaks new ground for time and frequency references. For the first time, it is possible to generate and distribute both analog and digital signals to multiple instruments and locations with just one product that fits in a single rack space. The TM-4D is three instruments in one: an Intelligent Reference/TM-4™ precise time and frequency reference, a digital signal distribution amplifier and an analog distribution amplifier. And it eliminates the need for multiple boxes.
-
Saluki Technology Inc.
S3871X series is a broadband benchtop solid state power amplifier and incorporates the patended spatial power combination technology. It is designed to have features of broad bandwidth, high gain, high power, wide dynamic range, low spurious signals and extremely load tolerant. These features enable the amplifier to be used as a cable test instrument covering multiple frequency bands.*Wide frequency range, 9kHz to 110GHz, max. 500W output power*