Force
exerts an influence.
See Also: Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
- Virginia Panel Corporation
product
Micro Coax, Contact, ITA, RG178
610141102
Primary mating contact 610140102. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistanc...show more -
product
Twin columns automated force test stand 36" travel - 10,000 lb
710SN
The advanced 710SN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
Load Cells
is a transducer that is used to create an electrical signal whose magnitude is directly proportional to the force being measured.
-
product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P-PLUS | VP 230047
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
-
product
Modeling Capacitors, Inductors, Insulators, Coils, Motors, and Sensors
AC/DC Module
The AC/DC Module is used for simulating electric, magnetic, and electromagnetic fields in static and low-frequency applications. Typical applications include capacitors, inductors, insulators, coils, motors, actuators, and sensors, with dedicated tools for extracting parameters such as resistance, capacitance, inductance, impedance, force, and torque.
-
product
Compact Timing Systems
NanoSync IV & NanoSync IV Low Profile
The NanoSync IV is a small form factor GPS Position, Navigation, Time (PNT) and Frequency reference system that provides multiple reference outputs and includes support for NTP & PTPv2 IEEE 1588-2008. The NanoSync IV has a Rubidium oscillator and is available with a civilian C/A GPS receiver or SAASM (Rockwell-Collins MPE-S GB-GRAM or Trimble Force 22E MRU GPS receiver) for military users. The NanoSync IV is packaged in a small, rugged enclosure ideally suited for embedded electronic warfare...show more -
product
Static Load Cells
2530 Series
2530 Series load cells with capacities of 5 N to 100 N are for use with 3300 and 5900 testing systems. 2530 Series Load cells with capacities of 500 N to 100 kN are for use with 3300 testing systems. The design, manufacture, and performance verification is conducted with materials testing applications in mind. Automatic transducer recognition and electrical calibration makes them easy to use. The load cells incorporate overload protection and can withstand loads up to 150% of their fo...show more -
product
Flight Line Armament Test System
SST
The Stores System Tester (SST) is a ruggedized flight line armament test system that enables real-time diagnostic analysis. U.S forces need to perform alternate mission equipment (AME) troubleshooting and diagnostic analysis on the flight line. BAE Systems' SST provides this capability in a one-person portable package.
-
product
Mini Power, Contact, Receiver, 65 Amp, 8 AWG
610116112
Primary mating contact 610115124. (May mate with other ITA contacts, as well.)Mini Power contacts carry up to 65 amperes continuous current. Maximum resistance is 1 Milliohms.Specifications Operating Current 65 Amps Max. Continuous – 8 AWG40 Amp Max. Continuous – 12 AWG30 Amp Max. Continuous – 14 AWG25 Amp Max. Continuous – 16 AWGContact Resistance 1 mOhms Max.Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body BrassContact Plating 50µ" Au ...show more -
product
Frequency Response Function
FRF
FFT Spectral Analysis. Frequency Response Function (FRF) is a commonly used measurement type of the Dynamic Signal Analyzer. FRF is defined as the ratio of response i.e. acceleration, velocity, or displacement with respect to the excitation force which is the reference.
-
product
RF Test Spectrum Measurements over CPRI
Integris 3000
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
product
Vibration Testing Equipment
Wewon Environmental Chambers Co, Ltd.
In Wewon, We have 2 powerful Vibration Testing Equipment. The Vibration Testing Equipment A is : EV210H0808VCSusb-E; The Vibration Testing Equipment B is: EV232H0809VCSusb-E. Technical parameters as below blank forms mentioned, The mainly difference is Sine Excitation Force, Frequency Range, Vibration Table’s size. Application for Vibration Test Equipment : The vibration test is to inspire or impact a part or device to see how it reacts in a real environment. The application of vibration test is very extensive, from the circuit board, aircraft, ships, rockets, missiles, automobiles and household appliances and other industrial products.
-
product
Countermeasures Dispenser Testers (CDT)
The nation’s Air Force, Army, Navy, Marine Corps, and key government agencies all depend on countermeasure dispensing systems – including the AN/ALE-47 and others – aboard their aircraft for self-protection against missile attacks and other airborne munitions. Especially when operating in contested areas, a properly-functioning countermeasure dispensing system can make all the difference to the success of a mission. That’s ample reason for aviation maintenance and flight prep crews to prefer the unmatched reliability of BAE Systems Rokar Countermeasure Dispenser Testers (CDT) for keeping their countermeasure dispensing systems performing effectively and safely.
-
product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Lead Free Probe
LFRE-1Z-10
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Mechanical Force Gauges
AMETEK Sensors, Test & Calibration
The mechanical force gauges from Chatillon offer high precision compression testing (Push) and tensile testing (Pull) at a low cost on a wide range of testing applications.
-
product
Current Mirrors
Analog Devices current mirrors are precision, high dynamic range, wide variable supply parts used for optical power monitoring, voltage biasing with current monitoring, and voltage-to-current conversion. Our current mirrors can monitor current down to as little as 3 nA and as much as 3 mA, with a linearity of 1% or better. The current dynamic range is 120 dB or 6 decades of current range, while the overcurrent protection feature in our devices forces the input pin to ground to avoid part damage. Over temperature (–40°C to +85°C) and process, the dynamic range only suffers 10 dB at the lower end of the range.
-
product
High Temperature Test System
129620A
Solartron Analytical, specialists in the design of precision impedance test equipment, has joined forces with high temperature Furnace specialists Carbolite, and sample holder specialists NorECS to produce a range of advanced high temperature materials characterization test systems.
-
product
Extender
3690-2
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Push Pull Force Gauge Meter
NK-10
Shenzhen Chuangxin Instruments Co., Ltd.
*This push pull force gauge Easy to be operated and can be installed with all kinds of test stands and clamps.*Peak holding function and continuous.*One year free maintenance.*Compact and artistic packing, easy to transit and stock.*Two kind of unit dual show at the same time,*don't need unit conversion. *NK Series: Newton and Kilogram dual unit; *NLB Series: Newton and Pound dual unit; *ALB: Pound and Kilogram dual unit.*Needle indicates, easy to read, high accuracy.
-
product
Atomic Force Microscope
HDM Series
The task of identifying nanoscale defects is a very time consuming process for engineers working with media and flat substrates. Park NX-HDM is an atomic force microscopy system that speeds up the defect review process by an order of magnitude through automated defect identification, scanning and analysis. Park NX-HDM links directly with a wide range of optical inspection tools, thus significantly increasing the automatic defect review throughput. In addition, Park NX-HDM provides accurate sub-a...show more -
product
Coax, Contact, ITA, 20 GHz, RG 223, Crimp, 90 Series Modules only
610102117
Primary mating contact 610102116. (May mate with other ITA contacts, as well.)20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps.It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsChara...show more -
product
Force Tensiometers
Sigma 700/701
The outstanding versatility of Sigma 700 and 701 force tensiometers makes them suitable for research and development, industrial quality control, routine measurements as well as academic research. Both instruments are computer controlled and have a high level of automation.
-
product
High 1.73 (49.00) - 8.00 (127.00) High Performance Lead Free Probe
LFRE-1H-8
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Bottle Cap Torque Testers
NJY Series Torque Tester is designed to measure the open force and lock force of the caps of bottles, spout bags and flexible tube packages.
-
product
Weld Force Gauges
This system is ideal for field measurement and data logging of forces between the tips of resistance spot welders.
-
product
Calibration Services
OMEGA offers a broad range of calibration services, with primary and secondary NIST traceable standards for calibrating temperature, infrared humidity, pressure, flow, and force products.
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of...show more -
product
Physical
This category covers test equipment for verification of resistance to heat, fire, tracking, mechanical stress, endurance, impact, force, torque, dimensional accuracy & similar related parameters as required by national and international safety regulatory agencies. These equipment are used to check Electrical WiringAccessories, Electrical Home Appliances, Industrial Luminaires, Motors and components or parts used in such products. Many of these test equipment are common to many standards and are essential for routine test purposes.
-
product
Centor Easy, graphical force gauge
CNR EA
The Centor Easy force gauges are designed to meet the production needs of its users. This group offers several features which are indispensable today for quality control, for example : ease of reading with its large backlit graphical display, RS232 output, memory of the last 100 values and ability to set thresholds with visual and sound alarms.
-
product
Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Lead Free Probe
LFRE-1J-7
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Crane Safety Monitor
CSM
PIAB CSM Crane Safety Monitor is an electronic control unit to be used in overload protection systems. The PIAB CSM evaluates and computes signals from force transducers and can be set for alarm at preset alarm limits. By installing the PIAB CSM, hazards for personnel and material are avoided. The PIAB CSM will also record the operation of the hoist. The PIAB CSM is designed both for indoor and outdoor operation in aggressive and demanding industrial environments.