Showing results: 16 - 30 of 97 items found.
-
FS-100 -
Walsn Enterprises Ltd.
FS-100 utilizes SMT technology which integrates a photoelectric sensor, a microprocessor, and a Human-Computer Interface (HCI) and an output interface together, sending out various outputs including an ON/OFF flame signal, a fault signal, a 4-20mA signal, and an RS-485 output (meets the MODBUS standard) via the quick connector.
-
ZY-3/ZY-3S -
Lisun Electronics Inc.
According to IEC60695-2-2 and IEC60695-11-5, ZY-3/ZY-3S Needle Flame Test is applied in the production and quality control department of lighting instrument, hyperpiesia electrical apparatus, domestic appliance, machine electric appliance, electrical machine, power tool, electronic instrument, electrician instrument and technical equipment. Also, it is fit for the industry of insulation material, engineering plastics and solid combustible material.
-
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
975MR -
Emerson
The Rosemount 975MR multi-spectrum infrared flame detector is based on accurately analyzing the multi-spectral signals by utilizing three separate IR sensors. The 975MR detects fuel and gas fires at long distances. For example, this product will detect a 1 ft2 (0.1m2) gasoline pan fire at 215 ft (65 m) in less than 5 seconds. The 975MR also provides the highest immunity to false alarms and enhanced overall coverage range.
-
MSA
Detection solutions tailored to your market's needs.
-
Syntel -
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
SPECTRA GT30 -
Ametek Power Instruments
The SpectraTM GT30 is easily mounted directly to the turbine case or on a short standoff pipe via a 3/4 inch NPT internal thread. The two-wire, 24 VDC loop-powered solid-state sensor is fully self-contained, therefore it does not require a separate amplifier. AMETEK offers various cabling options depending on the application.
-
FSE-100 -
Walsn Enterprises Ltd.
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
WKS-1208 -
Lisun Electronics Inc.
WKS-1208 Masks Flame Retardant Performance Tester is used to test the burning performance of the mask after contacting the flame at a certain linear velocity. It is special test instrument for the flame retardant performance of masks.
-
MSA
The FL500-H2 is an Ultraviolet / Infrared flame detector designed specifically to detect hydrogen (H2) fires. The FL500-H2 optical flame detector monitors for radiation emitted by a hydrogen flame in both the ultraviolet (UV) and infrared (IR) spectral ranges.
-
SMC 3200/3300 -
MSA
The SMC 3200/3300 Series Flame Detectors utilize proven, stable UV/IR technology to continuously monitor for flames in wet bench and commercial applications. Due to its compact size, it is also used for installation in certain production equipment.
-
CX-Z18 -
Shenzhen Chuangxin Instruments Co., Ltd.
Needle Flame Tester is made according to Standard IEC60695 and GB5169, meanwhile it’s a synthesis test equipment that can meet related standard requirements. It’s mainly used to simulate technical evaluation interior equipment. It’s applied to the risk of ignition test of electrotechnical equipment, parts and elements, also suitable for the risk of ignition test of solid electrical insulating materials or other combustible material.
-
HVR-LS/HVR-LSS -
Lisun Electronics Inc.
This equipment meets the requirements of ANSI/UL94, IEC60950-1, IEC695-2-2 and GB Standard. It is used to test the appliances and plastic materials parts of electrical equipment for the horizontal, vertical flammability test. The product tank shell is irony spray, and configured a transparent viewing window, the digital meter shows the burning time, afterflame time, afterglow time, this device has beautiful appearance, is easy to use and has reliable performance.
-
FLAME-CHEM -
Ocean Optics, Inc.
FLAME-CHEM spectrometers are fully integrated UV-Vis and Vis-NIR systems for measuring absorbance and transmission of liquid samples in cuvettes. FLAME-CHEM is a great option for teaching labs and research facilities where users seek the performance and flexibility advantages of the Flame spectrometer in a compact, small footprint instrument. Each FLAME-CHEM system comprises a preconfigured Flame spectrometer, a direct-attach light source and a cuvette holder for 1 cm pathlength cuvettes – all in a single package. UV-Vis (200-850 nm) and Vis-NIR (350-1000 nm) models are available. Add OceanView spectroscopy software (purchased separately) to complete your system.
-
TL105 -
MSA
The TL105 is a battery operated test lamp designed specifically to test General Monitors Flame Detectors. The TL105 is an explosion-proof test lamp that can be used with the FL4000H MSIR flame detector as well as any of the FL3100 Series Flame Detectors.