- Virginia Panel Corporation
product
Mini Power, Module, ITA, 90 Series, 19 Position
510108115
These mini power modules can withstand temperatures up to 140 °C. The faces of the power modules are screened with a red strip to indicate power.
-
product
Diamondx Test System
Diamondx semiconductor test system extends Cohu’s low-cost, high-throughput production test solution platforms to high pin count, higher site count wireless, mobility, SOC, Flat Panel Display drivers, Power Management, and microcontrollers. Designed to meet the cost drivers IC companies face, Diamondx extends Cohu’s leadership in lowering the cost of operations.
-
product
ITC Style VXI Module Shield Kits
* Box design for C-size ITC style PC Boards with 11 slots on their sides.* Pre-machined flat front panel with ejector handle cutouts.* Side shields include 0.375 inch wide vent slot on top and bottom sides for maximum cooling.* Shroudless design fits all VXI chassis.* Each kit includes side shields, front panel, ejector handles, two ejector face places with VXI and ICS logos, all hardware and assembly instructions.* Complimentary layout support includes PCB design template and CAD layout files.
-
product
Remote Temperature and Humidity Sensor
CHV-RTHS
The CHV-RTHS is a wall-mounted remote temperature and relative humidity sensor designed for use with select Crestron thermostats. The 1-1/2 inch diameter face of the CHV-RTHS protrudes just 1/8 inch from the wall surface and is easily painted or wallpapered to blend into the wall surface.
-
product
Masks Bacterial Filtration Efficiency Tester
Sataton Instruments Technology CO., Ltd
Face Masks bacterial filtration efficiency BFE tester is to determine the bacterial filtration efficiency (BFE) of medical face mask materials by employing a ratio of the upstream bacterial challenge to downstream residual concentration of the tested medical face mask materials. The tester provides certain flow rate of bacterial aerosol. The operator can measure the number of colony forming units passing through the medical face mask material, which is clamped between a six-stage Anderson cascade impactor and an aerosol chamber, expressed as a percentage of the number of colony forming units present in the challenge aerosol.
-
product
Face Masks Particulate Filtration Efficiency PFE Tester
GLE-20
GLE-20 is an oil-salt two-in-one Face Masks Particulate Filtration Efficiency PFE Tester. According to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1, etc. It is used to test the particulate filtering efficiency of daily protective masks and medical masks, and to determine the obstruction performance of ordinary fabrics and medical protective masks against a constant flow of airflow.
-
product
Time-of-Flight Sensing
Low-power time-of-flight sensing technology from ams enables host systems to measure distances accurately and at very high speed. Accurate distance measurements are used in various applications including presence detection, user face recognition and advanced cameras.
-
product
10 N Screw Flat Grips
10 N (2.2 lbf) screw flat grips are primarily used for tensile testing low force, soft materials such as yarn, paper, plastics, and cloth, in film or wire geometry. Grip faces are flat and rubber-coated, and the supplied coupling joints for the 10 N screw flat grips are designed for use on lower-capacity load cells.
-
product
Electrical Testing Monitoring
The IEC 61850 represents the migration from the analog to the digital world to the substations. Accordingly, industry faces a period of transition, also noticing the effects of IEC 61850 in the traditional checking and monitoring procedures.
-
product
Dual LED Modules
FOD 3105
The FOD Dual LED modules are designed specifically for test instruments application. They allow to have one output for two wavelengths in compact handheld device without couplers. The Module have an original ceramic ferrule that allows to incorporate the module on the front panel of a device and keep the access to the front face of the ferrule for cleaning and polishing.
-
product
Thermometers
Whatever jobsite needs you face, Klein Tools has a thermometer that will work for you. With both infrared and pocket models, you’ll be ensured a quick and accurate reading whether you can physically touch an object or not.
-
product
3D Machine Vision Process Control Solutions
In the age of automation and robotics, manufacturers utilizing automated dispensing in their assembly lines face growing challenges to maintain process control of their manufacturing processes. To eliminate errors and optimize product quality, they increasingly need the help of machine vision based “eyes of automation”. Whether manufacturing automobiles or medical devices, they need high-speed inspection tools to confirm the accuracy of their dispensing process and the overall quality of their products.
-
product
Interferometer
VFI-1200
The VFI is the interferometer of choice for industry leading photonics companies around the world. The VFI-1200 is an interferometric inspection system specifically designed for checking the surface quality and flatness of your cleaved or polished fibers. The VFI offers the perfect combination of a superb image quality with ease of use, and the reliability and robustness that our customers have come to expect from Arden products, resulting in fiber end face measurements that you can trust.
-
product
SAP Testing
ZenQ SAP Testing Services are on-demand, providing the best testing solution for identifying application errors before they make their way into production. Enterprises normally face challenges in analyzing SAP test requirements, handling compatibility issues while configuring, customizing and integrating different modules. We help our clients ease these testing challenges by having test accelerators to bring down cost overheads.
-
product
Fiber Fusion Splicer
KL-300T
Hangzhou Softel Optic Co., Ltd.
*Core to core alignment by PAS technology (PAS:Profile Alignment System)*Fiber core can be display clearly*Single X or Y view and X & Y view simultaneously*Auto check quality of cleaved end face*Display fiber cleaved and offset angle*Display core and clad offset*5.6 inch TFT color LCD monitor with clear digital image display*USB & VGA interface*Software upgrade via USB interface
-
product
4.0mm Hazardous Live Parts Probe
CX-4.0
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts through top openings. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN61010-1, UL3101-1, and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is made of stainless steel.
-
product
1 KN Capstan Grips For Yarn And Wire
These capstan grips are applicable for tensile testing yarn and metal wire with thickness less than 3 mm (0.12 in). Flat grip faces are used to hold the specimen. The grip faces are opened and closed by a cam with an operating lever. Ease-of-use and simple design are advantages of these 1 kN capstan grips for yarn.
-
product
End Face Inspection Microscopes
D SCOPE EFI – D SCOPE EFI-C – D SCOPE EFI-C LWD
The new D Scope EFI for MTP/MPO and multifibers field connectors is a cost effective microscope for inspecting fiber optic patchcords and cassettes.
-
product
Medical Masks Differential Pressure Tester
Sataton Instruments Technology CO., Ltd
Medical face mask differential pressure tester also called mask breathility tester is to determine the breathability of medical face mask materials. The tester can measure the differential pressure (Delta P) required to draw air through a measured surface area at a constant air flow rate is used to measure the air exchange pressure of the medical face mask materials. By providing the suction air through the holding sample, the tester can measure the Delta P by differential pressure transducer. It is to determine the air permeability and using comfort of the materials for medical mask.
-
product
Flat Front Panel Kits
* Pre-machined, single-slot wide flat front panel.* Fits virtually any VXI B and C-size board.* Ejectors pivot on mounting brackets that mount on the PC board.* Each kit includes front panel, ejector handles, two ejector face places with VXI and ICS logos, all hardware and assembly instructions.
-
product
ACoustic COllaborative Protection System
ACCOPS
Both manned and unmanned military vehicles face numerous kinds of direct fire, varying from incoming Small Arms Fire up to high kinetic armor piercing rounds. Especially when under armor, or unmanned, maintaining situational awareness is key.
-
product
Qualification and Quality Control Tests
Techsquare
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stres...show more -
product
Fiber Microscope
WL-D200S
The WL-D200 fiber microscopes provide dual-illumination, both coaxial and oblique, to produce the highest-quality image detail and superior view of fiber end face cleanliness and core condition.
-
product
MPO Visual Cable Verifier Kit
KI-TK832
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
product
Portable Connector End Face Geometry Interferometer
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operatio...show more -
product
1 KN Eccentric Roller Grips
These eccentric roller grips are specifically designed for tensile testing flexible materials, such as rubber and soft and semi-hard plastics. Named after the non-symmetric roller design, these grips employ a simple and quick clamping mechanism. They also have a self-tightening action, which maintains clamping of the specimen during testing regardless of any thickness reduction. In addition, the upper and lower grip faces are parallel grooved to help hold these soft materials.
-
product
Fume Hood Monitors And Controls
Research in laboratories helps advance science in many different disciplines. Professionals working in laboratories need protection from potentially hazardous compounds. Within laboratories, fume hoods are a primary source or protection. Fume hood face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust harmful vapors.
-
product
FlowSpec DDoS Mitigation
Large volumetric-based DDoS attacks are increasing in terms of frequency and scale at which they are perpetrated. With hundreds of-gigabits worth of attacks becoming commonplace, organizations not only face service interruptions for customers but the complete implosion of their infrastructure’s operation. In the face of this increasingly challenging threat landscape, BGP FlowSpec DDoS mitigation has emerged as one of the most effective techniques to mitigate DDoS attacks. Combined with an accurate and speedy detection system, it helps manage and synchronize working with firewalls to mitigate these attacks.
-
product
High Voltage Dry Reed Relays For up to 15 kV
SERIES 62 & 63
ungsten switches with power rating of 50 Watts maximum? Three switch types:5kV stand-off, 3.5kV switching10kV stand-off, 7.5kV switching15kV stand-off, 12.5kV switching? Series 62 has push-on connectors on top face for EHT and solder pins and nylon studs on the underside for PCB mounting
-
product
Automatic Driving System
ADS EVO
Vehicle developers face increasing pressure to reduce development times, while vehicle complexity is increasing. The ADS EVO ensures accurate and repeatable global test cycles on chassis dynamometers.
-
product
Battery Testing Machine
Dongguan Kejian Instrument Co., Ltd.
Test method is to use test sample cell on a plane, a diameter of 15.8 mm (5/8 inch) rods on the cross placed in the center of the sample.one 9.1 kg or 10 kg weight from a certain height (610 mm or 1000 mm) fell to the samples.Cylindrical or square battery in accepting the impact test, the vertical axis parallel to the plane, vertical steel column longitudinal axis.The longest axis vertical steel column square battery, the bedding face perpendicular to the direction of impact, each battery only accept an impact test.