Showing results: 2986 - 3000 of 3637 items found.
-
Macom Technology Solutions Holdings Inc.
MACOM’s FTTx amplifiers are designed for PON, RFoG and SFU receiver equipment and are offered in small, plastic QFN packages with integrated amplifier and attenuator functions. All parts cover the full 45 to 1000MHz / 1200MHz CATV band. 5v and 12v solutions are offered with power consumption of ≤ 1.5Watts. MACOM’s FTTx amplifiers are characterized with industry standard photodiodes, covering optical input ranges from -12 to +3dBm and each sample EVK comes complete with a photodiode and APC connector.
-
ViTec Co. Ltd
The hardware part of the measuring system of the test bench is built on the basis of equipment from National Instruments and contains the following components: multichannel switching system for signal conditioning SCXI, interrogation system of "fast-changing" voltage signals and AC power PXI, including M-series NI PXI-6220 board for SCXI module measuring channels, a high-performance Ethernet controller for the distributed I / O system and industrial control cFP-2110 running operating systems hard real-time, multi-channel vibration measurement complex K-5101.
-
ViTec Co. Ltd
The hardware part of the measuring system of the test bench is built on the basis of equipment from National Instruments and contains the following components: multichannel switching system for SCXI signal conditioning, interrogation system of "fast-changing" voltage signals and AC power PXI, including M-series NI PXI-6220 board for SCXI module measuring channels, a high-performance Ethernet controller for the distributed I / O system and industrial control cFP-2110 running operating systems hard real-time, multi-channel vibration measurement complex K-5101.
-
90-200-001 -
Pickering Interfaces Ltd.
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensure that order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start up also limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress on cabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
-
FLIR CM94 -
Teledyne FLIR
The FLIR CM94 tackles high-current measurements on demanding utility and industrial job sites. This rugged meter securely clamps larger conductors with an oversized jaw so you can take readings up to 2000 A AC & DC. With a CAT IV-1000 V safety rating, the CM94 is ready to work on overhead, underground and utility service equipment. Plus, it offers VFD mode to tackle noisy signal environments. The full-featured FLIR CM94 utility clamp meter delivers results for utility and industrial electricians.
-
HTC-300 -
Taylor Dynamometer, Inc.
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highwayhydraulic components. The 300 hp (224 kW) HTC Complete Bench is for the dealer that services components from a predominately medium size machine mix such as large construction equipment (loaders, dozers, excavators). The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
HTC-400 -
Taylor Dynamometer, Inc.
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highwayhydraulic components. The 400 hp (298 kW) HTC Complete Bench is for the dealer that services components from a predominately medium size machine mix such as large construction equipment (loaders, dozers, excavators).The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
Sper Scientific
Sper Scientific offers a wide selection of anemometers for directly measuring wind and air velocity. They will tell you all you need to know about the speed of the wind, the temperature, even humidity and heat stress information. The extraordinary range of uses that our meters provide have made them required equipment in a wide range of professional settings. Firefighters, farmers, HVAC technicians and military personnel all over the world use these meters to gather accurate, real-time data.
-
NEO TELE-TRONIX PVT. LTD
Since our establishment in the year 1975, we have been engaged in manufacturing and exporting Capacitance Tan-Delta Test Set. This test set is extensively used to measure dissipation and capacitance of various equipment. Manufactured at our well-equipped manufacturing unit as per set international quality standards using supreme quality components, this test set is tested thoroughly by our quality analysts on various defined parameters. Offered Capacitance Tan-Delta Test Set can be purchased from us at pocket-friendly prices.
-
Copernicus Technology Ltd
Copernicus Technology supply test hardware accessories to support Intermittent Fault Detection testing using VIFD™ and IFDIS™ test equipment, such as Interface Test Adapters (ITA). We also supply and repair general purpose and customer-spec test hardware accessories: ITAs, Break-Out Boxes (shown below) and Mobile Vibration Systems. The Mobile Vibration System can be quickly set up in repair bays for applying environmental stimulus to components and wiring harnesses during testing.
-
ALVI Technologies
Fullcheck automatically checks the device functions during power-on.Possible to document the operablility and the regular maintenance and calibration of the meterSensoface monitors the sensor and the measuring equipment and provides information on sensor selection and hanglingUnknown cell constants can easily be determined with a standard calibrationEMC design protects the meter from electromagnetic interference ensuring reliable measurement results even under unfavorable conditions.Measuring input is automatically switched over to the appropriate operating mode.Via the standard RS 232 interface your data can be immediately processed by a computer.DatasheetRelated Products
-
Del-Tron Precision, Inc.
Del-Tron’s belt drive actuators operate at speeds up to 5.1 meters per second (MPS) and do not require lubrication or maintenance under normal operating conditions. Del-Tron's DB series actuators are ideal for use in applications where speed is critical such as pick-and-place applications on high speed automation equipment. Another advantage of the new DB series is that they can provide travel lengths up to 6 meters while maintaining repeatability of +/- 0.025 mm and linear accuracy of +/- 0.083 mm per meter.
-
Signals & Systems India Private Limited
The Single Phase Portable Reference Standard (SPRS-1102) from SANDS is a portable meter test equipment that helps to calibrate the error present in the single-phase energy meter i.e. the meter under test (MUT). The SPRS supports both static and electro-mechanical types of meters. It can also be used to compute the voltage, current, energy, phase angle etc of the meter under test. It has an LCD display and an alphanumeric keypad to suit the user. It can be interfaced with the PC for analysis. It has the capability of storing 1000 test results.
-
STMicroelectronics
Protection against electrostatic discharges (ESD) is part of EMC Immunity (Electro Magnetic Compatibility) requirements. It is the ability for equipment to properly operate in its electromagnetic environment by limiting the reception of electromagnetic energy that may cause physical damage. ESD can be either conducted under the form of a transient voltage or can be radiated due to its fast rising time: powerful harmonics will generate erratic behavior by the application by coupling with other signals. Printed circuit boards must be protected against the effects of electrostatic discharge.
-
Cadence Design Systems
Power consumption affects the designer's ability to differentiate a product based on features, cost, performance, time to market, and even reliability. For mobile equipment, the explosion of applications leads to skyrocketing performance demands, in turn requiring innovative energy management. For data centers, where cooling represents a large proportion of overhead, power density management is critical to reduce cooling costs and increase reliability. Finally, at advanced process nodes, leakage is a critical issue, turning nearly all designs into advanced low-power designs.
