Showing results: 856 - 870 of 1253 items found.
-
41-752A-002 -
Pickering Interfaces Ltd.
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
41-752A-013 -
Pickering Interfaces Ltd.
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
CX-T04 -
Shenzhen Chuangxin Instruments Co., Ltd.
This Spring Impact hammer is strictly designed according to IEC60068-2-75, IEC884 and UL1244 GB/T2423.55-2006, GB4706.1, GB8898 and GB7000 standards. It is used to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance to IEC\EN, \UL\CSA and other international Standards.
-
MitM -
The Eastern Specialty Company
The Man-in-the-Middle Cable (Catalog No. MitM) was created to work with the T4000 and T4350 to enable a technician to use an electric vehicle rather than a very large load emulator to absorb the energy delivered by the DC fast charger during charger testing. It currently comes in 350 Amp CCSI and 200 Amp Tesla/NACS models, each with charging connector holders and digital temperature sensors.
-
IT6000C Series -
I-TECH Electronic Co., Ltd
The bi-directional programmable DC power supply of IT6000C series combines two devices in one: a power supply (source) and an electronic load (sink) with energy recovery. Based on these two functions, IT6000C offers the functionalityof two-quadrant operation. The regenerative capability enables the energyconsumed to be put back onto the grid cleanly, saving costs from energyconsumption and cooling, while not interfering with the grid. IT6000C seriesprovide 7 voltage grades, max. output voltage up to 2250V, support master-slaveparalleling with averaging current distribution, max. output power up to1.152MW. Built-in waveform generator supports generating arbitrary waveforms,and import LIST files for waveforms via front panel USB port. IT6000C is thecombination of high reliability, high efficient setting, safe and multiplemeasurement functions. IT6000C is a family of bi-directional, regenerativepower system with excellent performance, extensively used in aspects of highpower battery, automotive electronics, green energy, high speed testing etc.
-
45-100kw -
Shenzhen Setec Power Co., Ltd.
Solar pumping system is composed of a solar array,a pump and a solar pumping inverter. Based on the design philosophy that it is better to store water than electricity , there is no energy storing device such as storebattery in the system. The solar array,an aggregation of many solar modules connected in series and parallel , absorbs sunlight radiation and converts it into electrical energy , providing dynamical water for the whole system. The pumping inverter controls and adjusts the system operation and converts the DC produced by solar array into AC to drive the pump , and adjust the output frequency intensity to realize the maximumpower point tracking (MPPT) . The pump, drive by 3-phase AC motor,can draw water fromthe deep wells or rivers and lakes to pour into the storage tank or reservoir , or directly connect to the irrigation system ,fountain system,ect. According to the actual systemdemand and installation conditions,different types of pump such as centrifugal pump, axial flow pump,mixed-flow pump or deep-well pump can be used.
-
22-37kw -
Shenzhen Setec Power Co., Ltd.
Solar pumping system is composed of a solar array,a pump and a solar pumping inverter. Based on the design philosophy that it is better to store water than electricity , there is no energy storing device such as storebattery in the system. The solar array,an aggregation of many solar modules connected in series and parallel , absorbs sunlight radiation and converts it into electrical energy , providing dynamical water for the whole system. The pumping inverter controls and adjusts the system operation and converts the DC produced by solar array into AC to drive the pump , and adjust the output frequency intensity to realize the maximumpower point tracking (MPPT) . The pump, drive by 3-phase AC motor,can draw water fromthe deep wells or rivers and lakes to pour into the storage tank or reservoir , or directly connect to the irrigation system ,fountain system,ect. According to the actual systemdemand and installation conditions,different types of pump such as centrifugal pump, axial flow pump,mixed-flow pump or deep-well pump can be used.
-
TF Series -
Chuan Sheng Electronics Co., Ltd.
TF series, infrared temperature converters provide non-cotact measurement to caculate the surface temperature of the objects by measuring the energy of infrared light. So It is convenient to measure the surface temperature of especially moving objects. Its stainless case with integrated design combining sensors, optical system, and electronic circuits. It is easy to install by connecting the screw with other devices, and TF can be used in a wide range of industries.
-
SY2103 -
Hong Kong Songyang Industrial Ltd.
The new SY2103 series portable three phase phantom load stable power source, designed from new digital wave compound technology and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
Algodue elettronica
Additional voltage and current measurement channels in comparison with other standard three-phase devices.Current inputs for CTs or for clamps to grant an accurate current measurement.Continuous monitoring of the power quality and Class A certified measurements for voltage characteristics.Simultaneous recording of events, Min/Avg/Max LOG and energy counters.Several possibilities for instrument data transmission: Ethernet, Modbus TCP, 3G network.User-friendly instrument web interface with multilingual pages.
-
Vadatech Inc
VadaTech has one of the most extensive portfolios of A/D and D/A converters in the industry, in a range of form factors and a variety of channel and sampling rate options to meet all your data acquisition needs. Our ADC and DAC are widely used in high energy physics, military, aerospace and industrial applications thanks to variants based on MicroTCA.4, MicroTCA.0, FMC, OpenVPX and AdvancedTCA (ATCA).
-
ORTEC
Alpha spectroscopy is used to identify and quantify radionuclides based on the alpha particles emitted in the decay process. Similar to Gamma Spectroscopy, energy spectra are generated with high precision detectors and electronics and analyzed with special software. Typically, samples are measured following chemical separation to isolate the radionuclides of concern due to the complexity associated with correcting for these interferences with spectrum analysis software as is common for many Gamma Spectroscopy measurements.
-
ACCU-FLO METER -
LANDTEC
With an innovative edge, the LANDTEC ACCU-FLO Meter highlights a distinctive feature: A Zero Calibration User Check. The User Check allows the operator to verify that their LANDTEC ACCU-FLO Meter has not shifted, drifted or deviated from its original NIST-traceable Factory Calibration value. This ability makes the ACCU-FLO Meter unique, extremely useful on Gas-to-Energy projects, environmental compliance and essential for the carbon credit market.
-
Tenney Environmental
Tenney’s multipurpose environmental walk-in room is the perfect test site for everything from testing against humidity, temperature and various climate conditions. This walk-in chamber provides supreme temperature testing for large components and equipment. When your testing requires walk-in rooms, choose Tenney. Our test rooms feature automated process control, energy efficiency, and a vast range of features and options.
-
T8248 -
COMET SYSTEM, s.r.o.
CO2 concentration and temperature transmitter with two 0-10V outputs is specially designed for use in exacting interiors in building energy management and HVAC systems. It designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets. Large dual line LCD is possible to switch off.Computerized design ensures long term stability and fail indication. Transmitter is designed for use in non-aggressive environment.
