Showing results: 1096 - 1110 of 1262 items found.
-
Environment Associates Inc.
The purpose of Pyroshock (pyrotechnic shock) testing is to simulate the high-frequency, high-magnitude shock pulse experienced by an explosive event (such as an impact on a military tank or an explosive deployment charge). Pyroshock testing can expose failures in electronic components that are sensitive to high-frequency pyroshock energy. Common failures include: relay and crystal oscillator chatter, detachment of larger components from the circuit board, hard failures of small circuit components, and the dislodging of contaminants, which cause short circuits. Severe damage to crucial components used in space or in the military can produce critical results, such as loss of life, due to malfunction.
-
B-1022-B -
ROSS ENGINEERING CORPORATION
*Solenoid-Saver® eliminates AC hum and reduces heat generation for many types of solenoids.*Controlled application of current prevents coil burnout if high pull-in/low holding current AC or DC solenoids fail to pull-in completely.*Can adapt high pull-in low holding current solenoids to special voltages & frequencies 12V to 250V DC or 12V to 240V AC wideband 25-800Hz.*Optional optical isolated control input 4 to 10V, 5MA, 20 usec or more (or other control voltages) to actuate any high current solenoid directly by computer or other low power signal source.*For coils of 1 ohm to 3,500 ohms DC resistance requiring up to 70 amps during pull-in up to 120 milliseconds. Basic solenoid coil voltage and resistance must be specified.*Eliminates heat producing dropping resistors, bypass switch, dual coils, laminations, & shading coils.*Can increase pull-in and holding force of many types of solenoids.*Optional stored energy to delay solenoid release on loss of power.*Can be used as an added accessory to existing solenoid installation to eliminate AC hum, lower coil temperature and prevent coil burnout.*Optional high speed, 1 microsecond sensing, 1-10 millisecond actuation with stored energy Solenoid-Saver®
-
WSA -
Chuan Sheng Electronics Co., Ltd.
Due to environmental quality management and energy management, we've developed WSA, wind speed sensors which can be applied on ventilation systems, air conditioning, and negative pressure rooms. WSA is a high-accuracy duct type wind speed sensor which can quickly measure the small wind speed. It is stable, high-accurate, and with small drift only. Also, it can caculate the value of the current air volume depending on the measured cross-sectional area of the ducting. Ducting installation and screwless terminals help the users work more easily. Besides, the sensor is equipped with EMC anti-interference devices so that it can withstand strong electromagnetic interferences.
-
Analog Devices Inc.
Analog Devices' family of mobile I/O expanders are ideal for smartphone designs and portable devices that require a large extended keypad and/or expanded I/Os such as inventory scanners, medical equipment, and meter readers. Microprocessors in portable systems are GPIO constrained due to the number of functions they must interface with and control. They are also power hungry, making them inefficient for debouncing, polling, and key press scanning algorithms. ADI’s family of mobile I/O expanders offloads key scan and GPIO functions from the CPU, freeing up the processor for higher priority functions while saving energy.
-
Vanguard -
Ellisys Sàrl
The most advanced, most comprehensive Bluetooth protocol analyzer ever made. Building on a legacy of innovation, the Bluetooth Vanguard All-In-One Protocol Analysis System delivers new advances designed to ease the increasingly complex tasks of Bluetooth developers. Vanguard provides synchronized capture and analysis of BR/EDR, Bluetooth Low Energy, Wi-Fi 802.11 a/b/g/n/ac (3x3), WPAN 802.15.4 (all 16 2.4 GHz channels), raw 2.4 GHz RF spectrum analysis, HCI (USB, UART, SPI), generic SPI/UART/I2C/SWD communications, WCI-2, logic signals, and Audio I2S.
-
Gruenberg
Gruenberg ovens can be designed as Class A ovens to conform to OSHA, NFPA 86A, Factory Mutual (FM) and Factory Insurance Association (FIA) requirements. Class A ovens are equipped with a high exhaust rate: because the heating elements are an ignition source so a high exhaust rate is needed to dilute the volatile vapors below the “lower explosive limits.” As a result, the heating elements’ kW must be sufficiently increased to compensate for the heat loss caused by the above-normal exhaust rate. In addition, for a Class A oven to be energy efficient, the additional kW required must be carefully calculated according to solvent load and operating temperature requirements.
-
SPECTRO xSORT -
SPECTRO Analytical Instruments GmbH
The SPECTRO xSORT family of handheld ED-XRF spectrometers supplies elemental testing and spectrochemical analysis of myriad materials in widely varying conditions. These energy dispersive X-ray fluorescence devices are recognized for ruggedness and reliability on the job. They offer metals or nonmetals identification in seconds, with innovative technologies and designs that provide repeatable, laboratory-quality results. Simple, user-friendly displays and efficient ergonomics make these instruments extremely easy to use. At a range of affordable prices, SPECTRO xSORT spectrometers are leaders in their class for a broad spectrum of applications. - See more at: http://www.spectro.com/products/xrf-spectrometer/xsort-xrf-gun-handheld-analyzer#sthash.18piI4Px.dpuf
-
Electrical Testing Solutions
Explosive energy released during arcing faults will send more than 2,000 workers to burn centers this year. In addition, of approximately 350 persons killed in the work place by electricity last year, roughly 50% were related to arc flash. Most of these workers will not have been properly warned of the magnitude of arc flash, if at all. Although injuries are not as frequent as other job-related injuries, their severity makes the cost to human life and industry much greater. The monetary cost alone can easily exceed $1 million in medical expenses, equipment replacement, downtime, and insurance costs.
-
Signals & Systems India Private Limited
DUAL-CHANNEL AMR is a combined Modem for remote reading & local reading via Bluetooth through the mobile app without opening the enclosure/seals. Dual Channel AMR Modem is an innovative device that can be connected to any make of electronic energy meter by means of optical/ RS232 port, which is compliant to DLMS – IEC 62056-21 standard. AMR system is compatible with 4G network to push the power consumption-billing data, load survey data, and event data to a cloud-based server, with fallback to 3G & 2G. The modem can be programmed to send any abnormal events to any number instantly. The modems have a ‘store and forward’ facility.
-
ThermoSight® R-Series -
Teledyne FLIR
Built by the leader in infrared technology, the FLIR ThermoSight R-Series is the world''''s first line of thermal night vision rifle scopes for non-game hunting starting under $3,500. Compact and easy-to-use, the ThermoSight R-Series combines the features you want with the thermal performance you expect. The ThermoSight R-Series is the ideal night vision scope because it detects heat energy, instead of light. Conventional image intensified (I2) night vision scopes require illumination from moonlight or other sources, and can''''''''t reveal what''''''''s hiding in the shadows or in low-contrast environments like the R-Series.
-
ams AG
Proximity detection sensors measure reflected infrared (IR) energy to detect the presence of an object or person. The devices include an integrated LED driver and, in some devices, an integrated LED. The proximity detection devices provide four programmable LED drive currents and IR pulse repetitions. The proximity detection circuitry compensates for ambient light, allowing it to operate in environments ranging from bright sunlight to dark rooms. The wide dynamic range allows operation in short-distance detection applications behind dark glass, such as mobile phones. Proximity detection sensors can be used to replace a mechanical switch or to sense human gestures.
-
KoCoS Messtechnik AG
Dramatic advances in the field of measurement technology and the use of state-of-the-art micro-electronics have led to the development of a new generation of electricity meters which are far more accurate than their predecessors of just a few years ago. As well as measuring the exact amount of energy used, a high level of integration enables electronic meters to perform a number of additional functions. As a result, these meters are also more sensitive to network irregularities. This means that regular testing is the only way to ensure that a meter functions correctly, both during final factory tests and during the entire life span of a meter.
-
Instron
Instron pendulums are designed to meet the growing demand for accurate and repeatable impact testing on a wide range of materials. Used to determine the mechanical and physical properties of metals, polymers, composites, and finished products for both research and development (R&D) and quality control (QC), the pendulum family is capable of performing Charpy, Izod, and Tensile tests according to international standards. As uninstrumented systems, they provide the absorbed energy value. By fully instrumenting the pendulum, a more complete study of how the material reacts to impact can be gathered. This information is useful when evaluating the type of failure and the dynamic response of the material.
-
Keysight Technologies
Keysight products provide mobile phone designers and manufacturers with increased measurement speeds, improved accuracy, and exceptional flexibility for testing mobile devices. Our one box test sets cover all the major technology formats: LTE-Advanced, LTE (FDD and TDD), GSM/GPRS/EGPRS/E-EDGE, W-CDMA/HSPA/HSPA+/DC-HSDPA, cdma2000®/1xEV-DO/eHRPD, TD-SCDMA/TD-HSDPA/TD-HSUPA, IS-95, TIA/EIA-136, AMPS, Bluetooth®, Bluetooth Enhanced Data Rate (EDR), Bluetooth Low Energy, ZigBee™, Wireless LAN (WLAN), 802.11a/b/g, 802.11n, NFC/EMV, MIMO, and WiMAX™.
-
MESA-7220V2 -
HORIBA, Ltd.
The MESA-7220V2 measures both sulfur and chlorine in petroleum based products using the Monochromatic Energy Dispersive X-ray Fluorescence (EDXRF) method. A monochromatic X-ray source is used in order to obtain an ultra-low noise background which affords the best detection limits for both sulfur and chlorine.The detector window size was increased to collect more fluorescent X-rays and thus achieve lower level ppm values. This provides excellent, repeatable performance at both low and high concentrations of both elements.By adjusting the angle of the graphite crystal, the excitation beam can be measured to excite sulfur in the sample, increasing sensitivity.
