-
product
Substation Tester
JYH
JYH C CT PT Analyzer,full-featured, can not only satisfy the test requirements of various CTs (include TP class), such as the excitation characteristics (i.e., volt-ampere characteristics), ratio, polarity, secondary winding resistance, secondary burden, ratio error and phase displacement, but can also be used for the tests of various PTs, including excitation characteristics of the electromagnetic unit, ratio, polarity, secondary winding resistance, ratio error and phase displacement.
-
product
RFID
Leuze electronic GmbH + Co. KG
With RFID, no direct "visual contact" between the read-write unit and transponder is necessary. Information from the transponder is received by means of electromagnetic waves. As a result, these systems can be used practically and reliably under even the most adverse conditions.
-
product
NorthernRadar
WERA
The WERA system (WavE RAdar) is a shore based remote sensing system using the over the horizon radar technology to monitor ocean surface currents, waves and wind direction (Gurgel, 1999). This long range, high resolution monitoring system operates with radio frequencies between 4 and 50 MHz. A vertical polarized electromagnetic wave is coupled to the conductive ocean surface and follows the curvature of the earth.
-
product
Waveguide Switches
Waveguide switches are electromagnetic switches with hollow circular or rectangular cross-sections and are used for routing RF energy in microwave communications, broadcasting, and in radar applications. Waveguide switches can be used to transfer both power and communication signals, and the bandwidth of a waveguide is in relation to its size, and thus always referred to by its size (e.g. WR112, WR90, WR75 etc.). Compared to coaxial switches, waveguides can route extremely high power signals over a narrow bandwidth at low to high frequencies, and now Lightweight Waveguide series is available.
-
product
Magnetometers
The strength of magnetic fields can be determined with a magnetometer. Regardless of whether in the private sector or in the work environment, the increasing use of technology and networking also increases the exposure to magnetic and electromagnetic radiation. This radiation can have a negative effect on living beings, but also on sensitive electronic devices. Many effects are so unspecific that radiation is often not recognized as the cause. With a magnetometer you can measure how strong the r...show more -
product
Electromagnetic anechoic box/Shield box/Anechoic chamber
The necessity of a wireless system test has risen by the spread of recent wireless telecommunication equipment as shown in cellular phone, wireless LAN, RF-ID tag and ETC (Electronic Toll Collection system). It is necessary for a wireless test to be performed in anechoic environment in which an external noise is intercepted and a radio wave does not reflect internally. An anechoic chamber (room version of a shield box) is proper facilities but needs a wide space and a huge cost. Especially, the equipment under wireless system test on the production line can not radiate any signal radio wave outside before approval. The shield box satisfies these conditions.
-
product
EMI/EMC Testing
EMI/EMC testing can reliably predict product performance in any electromagnetic environment. Testing can also determine the possibility of interference with other equipment, possibly degrading performance. Testing may be required in order to comply with regulations or for informational and product improvement purposes.
-
product
Radiation Resistant Resolver
Computer Conversions Corporation
Computer Conversions GT Transducers are brushless, Electromagnetic, Rotary Sensors used to provide Precise Absolute or Incremental Position, and Velocity feedback in harsh environments. All Computer Conversions Transducers are continuous rotation, bidirectional, and electronically passive devices (no electronic components to degrade or fail), that require zero maintenance, and may be installed in virtually inaccessible locations.
-
product
High-frequency Induction Heater Unit
High-frequency induction heater unit is a high frequency generator for non-contact heating of metal using electromagnetic induction.
-
product
Electromagnetic Simulation Software Suite
EMTOOLS
EMTOOLS is a computational electromagnetic (CEM) software suite comprised of 16 different software codes. ACAL (Advanced Complex Algebra Library) is an out-of-core linear system solution library, using a hyper-matrix approach to partition the problem. The AntFarm™ (Antenna Farm) toolkit analyzes the radiation and electromagnetic interference (EMI) effects of single or multiple heterogeneous RF systems. Apatch™ software is an antenna design and analysis tool that provides antenna simulation and modeling by computing the radiation and receiving pattern of an antenna or antenna array installed in an operational environment...
-
product
Vector 2D Electromagnetic Solver
QuickWave-V2D
QuickWave V2D is a unique on the market and ultra fast Vector 2D (QW-V2D) electromagnetic solver is applicable to the analysis of axisymmetrical devices (which are also called Bodies Of Revolution) as large as 2100 wavelengths, including antennas (horns, rods, biconical), circular waveguide discontinuities, and resonators. It is based on the Maxwell equations re-expressed in cylindrical coordinates. Definition of a 2D long-section of the structure allows for hundreds times faster simulation than brute force 3D analysis.
-
product
EMF Field Tester
EMF 701
Range in guass:0.1m to 199.9m gauss. Range in Telsa:0.01 ~ 19.99 Tesla. Band width:30Hz to 300Hz. A cost effective, handheld meter provides the user with quick, reliable and easy way to measure electromagnetic field (EMF)
-
product
PSG Vector Signal Generator, 100 kHz to 44 GHz
E8267D
Test advanced receivers with realistic wideband radar, EW and Satcom waveforms with metrology-grade performance and versatile capabilitiesSimulate complex electromagnetic environments with up to 4 GHz of bandwidthReduce the time you spend creating complex signals with Signal Studio software: pulse building, noise power ratio (NPR), multi-tone signals, wireless & moreMaster your most complex signal requirements with the industry's best SSB phase noise: 143 dBc/Hz at 1 GHz (10 kHz offset)
-
product
Deep Transient Electromagnetic System
WTEM-2
WTEM-2 Medium-Deep/Deep Time Domain TEM Exploraiton System is applicable to medium-deep/deep transient electromagnetic sounding exploration. It features high power, short turn off time, high reliability, strong anti-interference performance, lightweight and low power consumption.
-
product
Electromagnetic Water Meter
WATERFLUX 3070
WATERFLUX 3070 is the first battery powered water meter for the drinking water industry that is capable of measuring flow, pressure and temperature with one sensor. Communication via Modbus RTU or pulse.
-
product
EM Software
QuickWave
QuickWave is a general-purpose electromagnetic simulator based on the conformal FDTD method and supplemented with a range of unique models for curved boundaries, media interfaces, modal excitation, and parameter extraction. It has a well-established position on the worldâs market due to approaching specific, challenging problems (often bound to QWEDâs specialists participation in the customerâs projects as consultants). That kind of approach causes that QuickWave has a very broad variety of information which can be extracted from the simulations in a form of different pre-processings, co-processings and post-processings.
-
product
Control Board for Motor, Pump & Valve
F1V04
Beijing SANKI Petroleum Technology Co., Ltd.
The main board issues a start signal and a low voltage signal (12v) for opening the electromagnetic valve, which are converted into strong voltage signals (220 VAC) to drive the electromagnetic valve (380 VAC) and the motor in our fuel dispensers system, thus completing the function of conversion from weak voltage power to strong voltage power. The control board circuit isolates high voltage interference signals via photoelectrical isolating components.
-
product
Inductive Sensors
Inductive Proximity Switches, self contained, depend on the output of an oscillator for their operation. The oscillator resonant circuit uses an open core coil to produce a concentrated high frequency electromagnetic (RF) field, which emerges from the active surface of the sensor. If a metal target (or other electrically conductive material) enters this field, eddy currents will be induced in it, causing the resonating oscillator to be damped.
-
product
Field Strength Meters
FIM-22 And FIM-41
The Models FIM-22 and FIM-41 are portable field strength meters designed to provide precise, direct measurements of electro-magnetic fields in the 200 kHz to 5.0 MHz spectrum. These units include a receiver, integral shielded loop antenna, precision attenuator, internal calibration source, and battery power supply. With calibration accuracy traceable to the National Institute of Standards and Technology, the FIM-22 and FIM-41 meet the most exacting requirements of government and industry. Their ...show more -
product
RF Safety Monitoring
MVG EME Guard XS 6GHz
The EME Guard XS is an RF measuring device to alert workers near RF emitters for protection of climbers and other RF-exposed workers. It continuously scans for electromagnetic waves and, via its built-in alarm and visual system, alerts users whenever the acceptable pre-selected limits have been exceeded. This RF Safety PPE is extremely easy to use and supports a safer working environment in the areas of installation and maintenance.
-
product
TEM Cells
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
product
Vibration Sensors
SKF Condition Monitoring Center
Various machine operating conditions concerning temperature extremes, magnetic fields, vibration range, frequency range, electromagnetic compatibility (EMC) and electrostatic discharge (ESD) conditions and the required signal quality necessitate the need for a variety of sensors.
-
product
Electromagnetic Interference Analysis Program
EMI Analyst™
EMI Analyst (U.S. Patent # 7,222,033) is the premier tool for ascertaining compliance with EMI requirements imposed by regulatory agencies.EMI Analyst is an electromagnetic interference analysis program that combines all four facets of EMI analysis into a single design package.
-
product
GoldenGate RFIC Simulation Software
GoldenGate RFIC Simulation and Analysis Software is an advanced simulation and analysis solution for integrated mixed signal RFIC designs that is fully integrated into the Cadence Analog Design Environment (ADE). GoldenGate is part of Keysight's RFIC simulation, analysis and verification solution that also includes Momentum for 3-D planar electromagnetic simulation, SystemVue & Ptolemy wireless test benches for system-level verification, and the Advanced Design System (ADS) Data Display for advanced data analysis. This suite links the RF system, subsystem, and component-level design and analysis as part of a unique and comprehensive RFIC design flow.
-
product
RFID Software
Radio Frequency Identification technology, commonly referred to as RFID, uses electromagnetic fields for the purposes of identifying and tracking objects. More recently, the technology has moved into mainstream applications that speed up the handling of manufactured goods and materials by attaching RFID tags to them. RFID technology has been around since the 1970s but its high cost and limited practical applications have discouraged its use up until recently.
-
product
Off-Air Testing Products
Understanding the challenges of the Electromagnetic Spectrum is paramount for Engineers that are charged with the design, characterization, validation of modern RF systems such as Communications Systems, RADAR Systems, and Electronic Warfare Systems.
-
product
RF Safety Monitoring
fieldSENSE 2.0
LBA's FieldSense 2.0 personal RF safety monitors are an effective and economical means to monitor the strength of electromagnetic (RF) fields from wireless cell phone towers, microwave ovens, television stations, and other common workplace RF sources between 50 and 6000 MHz, E-field and H-field (sensed as a plane wave). The Personal RF Monitor is essential RF safety equipment in complying with FCC, OSHA, Canadian and other workplace rf safety requirements.
-
product
Electromagnetics
Altair software is used across industries to solve a broad range of electromagnetic problems from static to low and high frequencies. Whether your application requires multiple frequency and time-domain techniques with true hybridization to enable efficient exploration of a broad spectrum of electromagnetic performance, or the simulation of magneto static, steady-state and transient conditions, we have the tools you need.
-
product
3D Guidance®
The 3D Guidance® electromagnetic tracking solution delivers exceptional performance and value for OEM image-guided interventional and therapy systems and medical trainers that require real-time navigation tracking capabilities. The 3D Guidance solution tracks 6DOF sensors that can be embedded into OEM instruments such as ultrasound probes, rigid and flexible scopes, and laparoscopic tools. Continuous in-vivo tracking is maintained through difficult anatomy, even when sensors are out of sight. Lo...show more -
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
