- Pickering Interfaces Inc.
product
PCI Digital I/O and Relay Driver Cards
a 32-channel Digital I/O card with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel.
-
product
MOSFET Drivers
Renesas' product portfolio includes MOSFET gate drivers for 3-phase motor applications. The drivers have built-in detection/protection functions and are suitable for inverter driver applications such as EGR, HVAC and EPS. Line up the products with LDOs for MCU, 24V battery system capability, built-in current sense amplifiers, and motor angle detection function. The products support unit downsizing and high performance.
-
product
Software Drivers and Application Software Packages
In test system development, the best hardware is only usable if its software control environment is robust and easy-to-use. If you are a test system developer, you need to look at both the hardware and software aspects of your vendors of choice.
-
product
RS-232 Micro Line Driver - DB9 Connector
Model 209
FEATURES: Compatible with PC; 386/486 Pentium Com Ports; Full Duplex to 19.2 KBPS; No AC or DC Power; Screw Terminals or RJ-11; Small Size. The Model 209F offers all the features of the Model 201 Short Haul Modem but in a package that is approximately one third the volume.
-
product
Diode Laser Driver
D200
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
product
T-Type Thermocouple, 32°F to 500°F Temperature Sensor
745685-T02
T-Type Thermocouple, 32°F to 500°F Temperature Sensor - The T-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure … measurements and predefined scaling coefficients for the T-Type Thermocouple and acquire synchronized temperature data in units of degrees. The T-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
Isolated RS-485
Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications. The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus.
-
product
Charger / Quick Charger / Adapter / LED Driver Test System
6010
6010 Charger / Quick Charger / Adapter / LED Driver Test System is able to meet multi-types power products test requirements,and its multi-U.U.T test simultaneously capability can significantly enhance the production line throughput. It also possess multi-modular combination that includes low noise analog AC source with Triac to simulate output, four sets precision power meter, two or four sets ripple noise / timing measurement module, four sets OVP DC power supply, 3310F series & 3332F/3336F Electronic Load module and unique design 3340F series for LED power driver output test.
-
product
USB-8486, USB, 1-Port, Fieldbus Interface Device
781160-01
The USB‑8486 is a FOUNDATION fieldbus device for developing applications with the NI‑FBUS driver, NI‑FBUS Configurator, and NI‑FBUS Monitor. FOUNDATION fieldbus is a popular industrial communication standard for process control applications. The NI‑FBUS Configurator features user-friendly multi-window interfaces to provide tools for the complete configuration, programming, and execution schedules of FOUNDATION fieldbus segments. The NI‑FBUS Monitor is a stand-alone application used to monitor, debug, and analyze fieldbus data packets.
-
product
PXIe-5122, 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope
779967-03
PXIe, 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope—The PXIe‑5122 high-resolution PXI oscilloscope has two channels with greater than 75 dBc spurious‑free dynamic range (SFDR) and flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution, low-noise measurements with up to 100 MS/s and 100 MHz of analog bandwidth. The PXIe‑5122 also features advanced PXI synchronization and data streaming capabilities.
-
product
USB-6346, 8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
785814-01
8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB-6346 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6346 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Temperature Input Device
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperatu...show more -
product
PCI-8532, 1-Port, DeviceNet Interface Device
781062-01
The PCI‑8532 is a high-speed DeviceNet Interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the controller area network (CAN) physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. The DeviceNet specifications are managed by OVDA, Inc. You can program the PCI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.
-
product
USB-6361, 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
782256-01
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
12-Ch SPST 5A-250VAC High Current Power Switching
YAV90CIN
12 Independent SPST relaysSwitching up to 5A 250Vac12 current measurement channelsGeneral inhibit inputCAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
-
product
Extenders & Line Drivers
Extenders and Line Drivers enable reliable, long distance signal transmission over coaxial, twisted pair, or fiber optic cabling.
-
product
NI-9862, CAN Interface Module
781639-01
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
product
34945EXT Distribution Board, For Two 87222, L7222C Transfer Switches And Six N181x SPDT Switches
Y1154A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
PCI Fault Insertion Switch Range for Differential Serial Interfaces
50-200/201
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN...show more -
product
MIL-STD-1553 A / B Test And Simulation PC / 104+ Module
PC104p-1553
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Supports ARINC429 and ARINC 664 operations
-
product
PXI 32 Channel I/O, Low Side Driver
40-413-002
A 32 channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only, a low side only (shown here)and a combined high and low side each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side voltage driving the high side voltage source is supplied from an external voltage source, permitting the module to drive high capacity loads without impacting the PXI chassis power supply.
-
product
WaferPro Express On-Wafer Measurement Program Software
WaferPro Express software performs automated wafer-level measurements of semiconductor devices such as transistors and circuit components. It provides turnkey drivers and test routines for a variety of instruments and wafer probers. Its new user interface makes it easy to setup and run complex wafer-level test plans, while powerful customization capabilities are enabled by the new Python programming environment.
-
product
4 CH LED Driver
LED-0401
UC INSTRUMENT’s LED-0401 Compact 4 Channel Computer-Controlled Universal LED Drivers are designed to drive a broad range of LED light sources. Maximum 1.5Acurrent can be output to each channel.
-
product
E-Type Thermocouple, 32°F to 900°F Temperature Sensor
745690-E001
E-Type Thermocouple, 32°F to 900°F Temperature Sensor - The E-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the E-Type Thermocouple and acquire synchronized temperature data in units of degrees. The E-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
RA Family Of Arm-based MCUs
RA6
The RA6 Series offers the widest integration of communication interfaces as well as the best performance level. These MCUs deliver up to 120MHz of CPU performance using an ArmⓇ CortexⓇ-M4 core and a memory range from 512kB to 2MB Flash. The series offers Ethernet, USB Full Speed and USB High Speed, QSPI, CAN, and TFT display driver integration. And, its embedded Secure Crypto Engine is full of features you can leverage in your higher-level solutions. The RA6 Series addresses a broad range of applications for IoT endpoints such as white goods, meters, and other industrial and consumer applications.
-
product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Modules
AXC1553-xT
MIL-STD-1553 Test and Simulation modules for XMC with 1 or 2 dual redundant streams plus 8 Discrete I/O’s (on Rear-I/O).*Concurrent BC, MRT (31) and Chronological/Mailbox Bus Monitor*Full Error Injection/Detection (AS4112)*Complex Triggering, Data Capture/Filtering & 100% Bus Recording*Physical Bus Replay*IRIG-B Time Encoder/Decoder*Programmable Bus Coupling, onboard Bus Network and variable Output amplitude*Full Function, Single Function and Simulator Only versions available*Drivers for Linux and Windows*Optional Databus Test and Analysis Software and RT Production Test Plan
-
product
Low Noise Amplifiers
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include low noise amplifiers, gain blocks, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
product
80 I/O Multifunction Module
YAV90832
16 Analog Inputs 0…15Vdc 10 Bits Zin= 1,2MOhm 24 Digital Inputs (Trigger) 32 Digital Outputs 11…45V/650mA 4 Analog Outputs 0…10Vdc 10 Bits 4 Outputs PWM CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
PXI-5124, 150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope
778757-01
150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope—The PXI‑5124 high-resolution PXI oscilloscope samples up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth. The PXI‑5124 also features PXI synchronization and data streaming capabilities.
-
product
PXIe 16 Bit Arbitrary Waveform Generator - up to 625 MS/s on 2 Channels
M4X.6621-X4
The M4x.66xx-x4 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PXI Express (PXIe) cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x4 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so ...show more -
product
Solution for High Density I/O Applications
BitBox
The BitBox is BitFlow''s new solution for high density I/O applications. Many machine makers require a large number of computer managed I/O signals for continuous control of the system state. This means controlling devices such strobes, solenoids, actuators, indicators etc. as well as gathering inputs from photo-detectors, switches, encoders and triggers. In general, BitFlow frame grabbers come with a fairly large number of inputs and outputs, but for some system this is simply not enough. Most ...show more