Showing results: 1 - 15 of 35 items found.
-
Kuhne electronic GmbH
The products have a big Dynamic Range, are highly linear and have low Noise Figures to keep the best possible quality of the signals to be converted. For this reason an internal filter for secondary wave suppression is implemented.
-
ERAVANT
In digital signal processing, a digital down-converter (DDC) converts a digitized, band-limited signal to a lower frequency signal at a lower sampling rate in order to simplify the subsequent radio stages.
-
Abaco Systems Inc
A Digital Down Converter performs channel access functions in digital receivers. It is used for extracting a channel (frequency band) of interest in a wideband signal. Abaco Systems' wideband DDC core employs a quad DDC architecture to achieve ultra high performances. The core accepts up to 16-bit complex data and can process 1GSPS continuously. With a fully programmable architecture at all stages of the processing, this core combines flexibility and speed and can be used in combination with our dual-channel 1GSPS ADC module.
-
LS-27-D -
Lumistar Inc.
The Lumistar LS-27-D3 TwoChannel Quad Band PCI Down Converter product is a 3rd generation high-density, high performance down converter designed using the sameadvanced technology as in the industry leading LS-25 PCIReceiver. The down-converter converts one or two independent channels of up to four RF frequency bands down to a 70 MHz IF output. The LS-27-D3 is typically used in conjunction with theLumistar LS-35 Series Digital IF Receiver/Combiner to provide one or two independent telemetry receivers, or a dual diversity combining receiver, with up to two multi-mode demodulators and bit synchronizers in a two-slot PCI interface. The number of channels and frequency band designations can be specified at the time of order. Please see the data sheet for the LS-35-R Digital IF Receiver/Combiner for more information.
-
Lumistar Inc.
Lumistar offers single PCI slot multi-band FM receivers. The same product in a “drive Bay” configuration is available. All Lumistar FM receivers can come without the FM demodulator use as antenna tracking receivers or for use as down converters used with an IF receiver for multi-mode digital combining and demodulation. Dual channel versions are also available.
-
M5201A -
Keysight Technologies
Single-slot PXIe low-IF downconverter module with a 2 to 16 GHz RF input frequency range and 0.01 to 2.4 GHz IF range
-
LS-25-D -
Lumistar Inc.
Lumistar offers single PCI slot multi-band FM receivers. The same product in a “drive Bay” configuration is available. All Lumistar FM receivers can come without the FM demodulator use as antenna tracking receivers or for use as down converters used with an IF receiver for multi-mode digital combining and demodulation. Dual channel versions are also available.
-
GX3788 -
Marvin Test Solutions, Inc.
The GX3788 is a user configurable, FPGA-based, 3U PXI multi-function card which supports digital and analog test capabilities. The card employs the Altera Stratix III FPGA which features over 45,000 logic elements and 1.836 Kb of memory. The GX3788 is based on the GX3700 FPGA card and includes an integral daughter board which provides (8) differential input, 16-bit, 250 MS/s A to D converters and (8), 16-bit, 1 MS/s, D to A converters. The module's FPGA is pre-programmed, providing access to all digital and analog functions. Alternatively, users can program or modify the FPGA , allowing user to adapt the module to their own specific test needs. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
CPCI-DA8-2 -
ALPHI Technology Corporation
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system.
-
CPCI-DA8-1 -
ALPHI Technology Corporation
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA8 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
CPCI-DA16-1 -
ALPHI Technology Corporation
The CPCI-DA16 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA16 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
CPCI-DA16-2 -
ALPHI Technology Corporation
The CPCI-DA16 is a slave Digital to Analog board thatis managed by the host processor on the CPCI bus.The card contains a state machine that performs mostof the work of outputting data, in order to minimize theimpact to the HOST system.
-
34951A -
Keysight Technologies
The Keysight 34951A module for the 34980A Multifunction Switch/Measure Unit has four electronically calibrated analog channels that can output up to +/-16V DC or +/-20mA DC with 16 bits of resolution. Each channel can be updated individually with a 200 kHz update rate. You can use the standard waveforms provided or create your own with over 500,000 points. These points can be dynamically allocated among one or more channels and output as a point-to-point arb.
-
M9185A -
Keysight Technologies
The M9185A is a fully independent, isolated D/A converter that is capable of supplying high voltage levels in parallel of up to eight or sixteen channels. Each channel is able to output up to 16V as stimulus signals to Device Under Tests (DUTs).
-
34952A -
Keysight Technologies
The Keysight 34952A module for the 34980A Multifunction Switch/Measure Unit allows great flexibility for a variety of sense and control applications.It combines the following on a single earth-referenced module: