-
product
RAMP TEST SET
AN/USM-719
Tel-Instrument Electronics Corp.
Based on entirely new up-to-date technology and digital architecture; the AN/USM-719 large 4.75" x 3.5" in. color LCD screen and surrounding soft-keys and keyboard provides easy and quick access to a multiple of test screens menus, and display options affording single man operation, instant results, and a host of pre-programmed and manually variable parameters to meet the most demanding requirement's for testing of advabced airborne avionic and transponder/interrogator systems.
-
product
Seismic Signal Conditioners
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
product
LGA 1151 Intel® Xeon® E3 v5/v6 & 6th/7th Generation Core™ ATX Server Board with 4 DDR4, 4 PCIe, 3 PCI, 6 USB 3.0, 6 COM, 6 SATA3, Quad/Dual LANs, IPMI
ASMB-785
- Supports LGA 1151 Intel® Xeon® E3-1200 v5/v6 and 6th/7th Generation Core™ i7/i5/i3 processors- DDR4 2400/2133/1866/1600/1333 MHz ECC/Non-ECC UDIMM up to 64 GB- One Gen 3.0 PCIe x16 link (or two PCIe x16 slots with x8 link), two PCIe x4, and three PCI slots- Triple display - two DVI-D and one VGA ports- Supports up to ten RS-232 or six RS-232 and four RS-422/485 ports- Rackmount optimized placement with positive air flow design- 0 ~ 60 °C ambient operation temperature range
-
product
HDMI Over Fiber Transmitter and Reciever
QuestTel''''s HDMI Transmitter and Reciever singlemode extender over fiber optic cable integrates HDbitT technology in one standalone kit, it allows you to transport HDMI 4KX2K - 25/30Hz signal up to 20km from the source device to destination display using SC connectors.This HDMI extender supports IR back transmission function. It features with low signal loss and tolerance for electromagnetic interference.
-
product
Signal conditioning
Simple parameterization of the sensors and visualization of the measured values via the on-site display.
-
product
Light Meter
LI-250A
The LI-250A is a portable meter that displays the output from any LI-COR light sensor that has a cable terminated with a BNC connector. It shows instantaneous values or 15-second averages of values from a sensor.
-
product
AC Electronic Load
IT8600 Series
IT8600 is ITECH latest series of AC/DC electronic loads with power range 0~14.4 kVA and adjustable frequency 45 Hz ~ 450 Hz. The unique oscilloscope waveform display function of IT8600's can display input voltage & current as waveform. It is equipped with measurement modes for different parameters such as inrush current, peak value, effective value, PF (power factor).
-
product
Digital Multimeter
VOAC7602
Using the high-resolution LCD screen, you can view the measured values while watching the average, the maximum and the minimum values. Moreover, VOAC7602 enables you to observe the statistical values while viewing the Trend and the Histogram charts. Other than those above, there are various kinds of combinations of displays available to be shown aside and these can be chosen from many functions, such as LIMIT function, and Analog meter display, which is effective for analog judgment.
-
product
Surface Roughness Meters
This instrument is compatible with four standards of site to measure surface roughness of various machinery-processed parts, calculate corresponding and clearly display all measurement parameters.When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier.
-
product
ZIPLEVEL EZDepth
The revolutionary ZIPLEVEL EZDepth is an inexpensive alternative to costly cab based digital depth instruments. EZDepth is built from the core of the quarter century proven ZIPLEVEL PRO-2000…the world’s only pressurized, bubble free High Precision Altimeter. Unlike conventional technologies, EZDepth installs in minutes to directly display depths over unlimited ranges without line-of-sight, satellite horizons or complex arrays of inclinometer sensors. Its optional ZIPLEVEL SmartLink sends data to...show more -
product
Digital Oscilloscope
Shenzhen Graigar Technology Co.,Ltd.
A digital oscilloscope is a complex electronic device composed of various software and electronic hardware modules that work together to capture, process, display and store data that represents the signals of interest of an operator
-
product
Linerizers and Integrators
Linearizers with freely selectable parameters are designed for industrial applications in which non-linear analog signals or frequencies are to be linearized on the display and at the analog and data outputs. Depending on requirements, devices with 19 to 4000 linearization points are manufactured. The linearization can be entered directly via the device keyboard or via the serial interface from the PC. Several linearization methods are available, such as direct overwriting of the display with the desired value, table with setpoint and actual values or polynomial linearization.
-
product
10 MHz To 67 GHz USB Wide Dynamic Range Average Power Sensor
U2057XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the in...show more -
product
Power Meters
Teledyne Test Tools range of digital power meters are for single-phase (1P/2W) AC power measurements with a test Bandwidth ranging from DC, 0.1 Hz to 100 kHz. The T3PM1006 model features a 4” TFT LCD screen with a five-digit measurement display. It offers 19 power measurement parameters to choose from, integration measurement function, front/rear panel input terminals, and various communication interfaces to help users to make convenient and accurate power measurement. The T3PM1100 model offers ...show more -
product
CO2 Concentration Transmitter
T5240
CO2 concentration transmitter with 0-10V output is built in a durable case. Output range is user adjustable. Large dual line LCD is an advantage. Display is possible to switch off.
-
product
Spectrum Analyzers
PeakTech Prüf- und Messtechnik GmbH
Spectrum analyzers are used to display the amplitude distribution over a certain frequency range.
-
product
ALC (AGC) FTTB Optical Receiver
BG9244x-LD
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai BG9244x-LD product series have the bandwidth of 47~862MHz,with ALC（AGC）function, two outputs, the output level Vo=104dBμV （Pin:-7~+2dBm, APD=8dB）. The device has built-level gain and equalization adjustment, visual display about optical power, and can choose 1way or 2 ways high level output by illustration. It applies to FTTB optical access to network, is an ONU optical receiver unit of RFTV radio network with low power, high performance, high cost- effective.
-
product
10 Digit Rate/Batch Counter (Analogue)
CS2-TM-Analogue
Chuan Sheng Electronics Co., Ltd.
The CS2-TM Totalizer controller provide high accuracy measurement, display, control and communication (Modbus RTU mode) of 0~10V/4~20mA from flow meter or mV from Shunt for Amp-Hour.There are two display screen and 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue, 1 Pulse and RS485 port available. They are also support fantastic control function as like as N, R, C mode for totalizer and batch control.
-
product
Instrumentation System For Towing Dynamometers
DynCtrl-II
Taylor Dynamometer’s DynCntrl-II instrumentation system for towing dynamometers includes a ruggedized, Wi-Fi, touchscreen tablet PC with an integrated graphic heads-up display and a robust instrumentation package mounted in a sealed Nema enclosure. Our easy to use, intuitive, DynCntrl-II software not only makes testing simple, but also displays and records multiple channels of real time data.
-
product
Load Cell Displays
We carry a wide range of digital displays for strain gage load cells. There are many options available to our load cell displays such as analog outputs to interface with a PLC, digital outputs for computer interfaces, I/O and relay outputs to control batching and checkweighing scales, and wireless load cell indicators.
-
product
Display
XY Plotter
XY Plotter is used for visualizing (form evaluation) the transfer characteristics of two values to be measured. The following instruments can be used for transfer characteristics: DC and AC voltmeters, a selective AC voltmeter, a frequency meter, and a phase meter. Characteristics can be displayed in 3 planes (XY, XT, and YT), as well as in a three-dimensional (XYT) view.
-
product
Dynamic Weighing System for Excavators
Loadtronic 3E
The load in the bucket is weighed during normal lifting cycle. The weighing can be started automatically or manually. The display will show the weight currently in the bucket, and the running total. Also, the number of buckets delivered is shown. The weighing system can be used as a tool toavoid over- and underloading of trucks. All loadings are stored in the main unit and can be retrieved either for printing a receipt or for transfer to PC (USB stick/ SMS). Databases of customers, materials etc. can be transferred between the office PC and the Loadtronic 3E system (using USB stick). The files can be viewed and edited in MS Office Excel or Notepad.
-
product
Surveyor Thickness Gauge
Multigauge 5650
The Multigauge 5650 Surveyor Thickness Gauge is a simple, robust ultrasonic thickness gauge designed specifically for ship and small craft surveyors, but can also be used in applications where different measurement modes are required. The user has a choice of Multiple Echo, Echo to Echo or Single Echo to cover all requirements. The gauge can be used for metal, GRP or plastic measurement and it automatically switches modes and settings depending on the type of probe fitted. The easy to use keypad...show more -
product
MAGNA Series "Large Digit" Clocks
Models CLK4 & CLK6
4-digit model (CLK4) with HH:MM display, or 6-digit model (CLK6) with HH:MM:SS display. Large-digit displays with a digit height of 2.2" (57 mm), 4.0" (102 mm), 5.7" (144 mm), 7.9" (200 mm), or 11.0" (280 mm) for long viewing distances. Optional relays and data I/O. Choice of display brightness and cases for indoor or outdoor mounting.
-
product
PXI Vector Signal Analyzer
Keysight's PXIe vector signal analyzers are ideal for design validation and manufacturing applications that require fast, high quality measurements where quality control, product conformance and test optimization are essential. With a small footprint, speed, scalability repeatability, and the flexibility to configure a solution with a shared processor, frame/chassis, display, and interface, PXIe vector signal analyzers provide the building blocks for your single or multi-channel modular test solution.
-
product
Dual Display HVAC Clamp Meter w/ Temperature
DL389B
UEi Test & Measurement Instruments
• Dual Display• Input jack locks• Worklight• Backlit display• Auto/manual ranging• Min/Max• Test lead storage• Magnetic mount• User temperature calibration• Auto power off• Degree ºF or ºC• Low battery indicator• Test lead holder on clamp• 2-Year limited warranty
-
product
AC DC Test Equipment
The products impress with a variety of technical features: TFT display, Ethernet interface, automatic test sequence to a fully electronic generator for even faster and more accurate tests. Our safety testers can be used both stand-alone without a PC as well as integrate with existing systems.
-
product
Infrared Motion Sensor
ENVIROMUX-IMD
Registers movement in the area covered. Condition display via LED. Provides immunity from common-mode signals such as the effect of strong hot or cold air currents, variation in ambient temperature, background radiation and acoustic noise. 24 dual-element detection zones for long, mid and short range protections. Surface or corner mounting. Pulse count or single shot triggering. Good RFI protection. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45...show more -
product
Industrial Inspection Cameras
Industrial Inspection Cameras are our top-of-the-line inspection cameras. They feature glass lenses, superior optics, crystal-clear displays, and compatibility with the thinnest probes on the market. All Industrial Inspection Cameras were recently upgraded to capture VGA (640 x 480 pixel) resolution video clips and remove glare and reflections from them. All cameras in this sub-category are made in Taiwan, making them compliant with the Trade Agreements Act (TAA) of 1979a necessity for many buyers with the U.S. military and federal agencies.
-
product
DisplayPort v1.3 Protocol Analysis Probe
FS4500
The FuturePlus FS4500 DisplayPort Analysis Probe provides a mechanical, electrical and software interface to the DisplayPort bus, a digital display interface standard supported by the Video Electronics Standards Association (VESA). The FS4500 is used to design and debug computer motherboards, monitors, home theater systems, and silicon chips incorporating DisplayPort technology.
