Showing product results. 1 - 15 of 5266 products found.
-
-
HIOKI E.E. Corp
Sensitivity of Conventional Probes Deliver Precise Measurement of Low Current Waveforms from 1 mA. High-precision Current Sensors, DC to 4 MHz, DC to 20 kHz, up to 50 kHz and load current sensors,
-
DARE Electronics
Current sensors are designed to monitor the presence or absence of AC or DC current and are available in an assortment of standard & custom models with hermetic or gasket seal models designed to withstand severe environmental conditions.
-
IPC-Series - Isabellenhütte Heusler GmbH & Co. KG
The IPC series are digital, precise phase current sensors with a wide range of possible applications. Different designs with different measurement ranges between 100 Ato 2,500 Aare available.Because of this modular principle of the shunt-based phase current sensor, we are able to offer our customers a quick solution for the requirements. Due to their high bandwidth, high linearity and very low temperature coefficients, our modules are perfect for the high-precision current measurement in modern control systems and converters.
-
Bender Inc.
Excellent measurement technology requires high-quality current transformers. The product portfolio comprises a wide range of current transformers for load currents (operating currents) and residual currents (RCM). Different designs cover a variety of installation situations and metrological requirements, and enable retrofitting. AC/DC sensitive measuring current transformers use a special measurement method to detect both AC and DC currents of different frequencies.
-
DCP-BTA - Vernier Software & Technology, LLC
The Current Probe measures DC and low-frequency AC currents up to 600 mA. Use Current Probes in combination with Differential Voltage Probes to investigate Ohm's Law and explore series and parallel circuits. The 0.1 shunt resistor minimizes changes to your circuit. If currents will exceed 1 A, use the High Current Sensor.
-
Innovar Systems Ltd.
Innovar Current Sources are the standard in the circuit breaker industry. Our Current Sources supply regulated current from 1 amp to 100,000 amps with incredible accuracy, along with providing a full set of features that is unmatched by any other Current Source in the market.
-
Yokogawa Test & Measurement Corp.
Current probes allow you to measure DC or AC current. Yokogawa's selection of current probes allow measurements ranges up to 500 ARMS and bandwidths up to 100MHz.
-
DCFlex - Power Electronic Measurments Ltd
The DCflex is an easy to use, low cost, thin and clip-around DC current probe. It is suitable for measuring large DC currents of >2kA. The DCflex takes a single shot measurement of the DC current with a typical accuracy of ±1%. It is important to understand that the DCflex does not provide a continuous measurement of DC current.
-
Howard Butler Ltd.
A range of ring type current transformers suitable for primary currents from 1A-5000A with 1A or 5A secondaries. This standard range of measuring and protective current transformers is available as resin coated or tape wrapped.
-
Brultech Research Inc.
The Current Transformer (CT) is the sensor which measures the amount of current draw from the wire it is installed on.
-
Analog Devices Inc.
Analog Devices current mirrors are precision, high dynamic range, wide variable supply parts used for optical power monitoring, voltage biasing with current monitoring, and voltage-to-current conversion. Our current mirrors can monitor current down to as little as 3 nA and as much as 3 mA, with a linearity of 1% or better. The current dynamic range is 120 dB or 6 decades of current range, while the overcurrent protection feature in our devices forces the input pin to ground to avoid part damage. Over temperature (–40°C to +85°C) and process, the dynamic range only suffers 10 dB at the lower end of the range.
-
-
Rishabh Instruments Pvt. Ltd.,
Summation CTs are designed to summarize several synchronous Alternating Currents of equal phase relation. They are used to add secondary currents of several main CTs in order to measure with one CT only. That means the primary currents are added & divided by the number of inputs
-
STMicroelectronics
A current sense amplifier is a differential amplifier providing an analog output voltage proportional to the current flowing into a load connected on its input.