- Virginia Panel Corporation
product
Tool, Crimp, 10 Amp TriPaddle, Thermocouple/Micro Power, Receiver Or ITA
910101102
Tool, Crimp, 10 Amp TriPaddle, Thermocouple/Micro Power, Receiver or ITA
-
product
Constantan, Type T (°C) Contact
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
Tool, Crimp, QuadraPaddle, Receiver
910101125
Crimp Tool Part # 910 101 125 is used to crimp receiver QuadraPaddle contacts.
-
product
Connector, 50-Pin SGMC, Female, 5A, Crimp Pin, Without Backshell
C050FFX-1CP-0A
This 50-pin SGMC connector is designed to allow users to directly terminate with crimp connections and is suitable for 22 AWG copper wire. Supplied without a backshell. Screwlocks are provided to secure the connector to its associated product.
-
product
Connector, D-Type 50-Pin Male With Crimp Pins
GT96108
Connector, D-type 50-pin male with solder pins.
-
product
Tool, Crimp, 75 Ohm Coax, Receiver and ITA, Hex Crimp
910104139
Used to crimp the ferrule on 75 Ohm contacts. Also included in tool kit p/n # 910102107.
-
product
Connector, 50-Pin SGMC, Female, 5A, Crimp Pin, With Backshell
C050FFR-1CP-0A
This 50-pin SGMC connector is designed to allow users to directly terminate with crimp connections and is suitable for 22 AWG copper wire. Supplied with a backshell that has an integral cable clamp. Screwlocks are provided to secure the connector to its associated product.
-
product
Signal, Module, ITA, i2 MX, 84 position, QuadraPaddle, Crimp
510144002
Signal, Module, ITA, i2 MX, 84 position, QuadraPaddle, Crimp
-
product
Tool, Locator, Micro Coax, Receiver
910101135
Included with Crimp tool kit p/n 910101132 and kit p/n 910101131.
-
product
Signal , Module, Receiver, QuadraPaddle, iCon Series, 160 Position, for crimp contacts
510160101
Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
product
Alumel, Type K (°C) Contacts
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
Wire Crimp Testers
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
product
Solar PV Test Equipment
Di-log offer a comprehensive range of Solar PV test equipment and tools to service the renewable industry. The range offers irradiance meters, DC current clamp , meters, crimp tools, roof surveying and protective gloves.
-
product
Hand Crimp Tool For Scorpion Connector Pins
C020AFR-2CP-2A-O
Hand operated crimp tool for pins fitted into a Scorpion connector housing.
-
product
Crimp Tester
M004
To calculate the crimp in yarn affected by knitting or weaving, to determine actual yarn usage.
-
product
Thermocouple, Contact, Receiver, Alumel, Type K (°C)
610113132
Primary mating contact 610113134.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Test Solutions Services
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
product
Coax, Contact, ITA, 75 Ohm, RG179
610103169
Primary mating contact 610104157. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield - 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Loss -1.64 @ 3 ...show more -
product
Tool, Crimp Die, Micro Coax, f/ RG 316 and RG 179 wire
910101133
Included in Tool kit 910101132.
-
product
Wire Crimp Pull Tester (Motorized)
WT3-201M
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
product
Crimp Tester
TF125
TESTEX Testing Equipment Systems Ltd.
Crimp Tester, to calculate the crimp in yarn affected by knitting or weaving by taking apart the yarn from a piece of given-length fabric, unbending it under given force and measuring its length, to determine actual yarn usage.
-
product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp only
610110101
Primary mating contact 610110108. (May mate with other ITA contacts, as well.)p/n 610110125 TriPaddle Receiver 50µ" AU plating.p/n 610110101 TriPaddle Receiver 30µ" AU plating.Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Crimp Tool DIN 41612
40-964-160-C
A DIN 41612 Crimp Tool suitable for making crimped terminal connections to individual wires and cables. Please see our product 40-964-160-E for the Connector Pin Extractor Tool.
-
product
Tool, Crimp Die, Mini Coax, RG316 and RG178, with Locator
910104126
Tool, Crimp Die, Mini Coax, RG316 and RG178, with Locator.
-
product
Micro and Milliohmmeter
AD-7110
The instrument AD-7110 is designed to measure, with high accuracy, resistance conductive elements of power devices: motor windings, transformer windings, conductor rails, inspecting the electrical conductivity of screw connections, crimp, welded state of the contacts of switches and relays current up to 100 A .
-
product
Connector, Cable Mount, 25 Pin 1.27mm Pitch Micro-D, Female, Crimp Pin
C025CFR-1CP-0A
This 25 pin micro-D connector is designed to allow users to directly terminate with crimped connections and is suitable for 26 AWG copper wire. Screwlocks are provided to secure the connector to its associated product. This connector is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
product
Tool, Crimp, Mini Coax, RG 316 and RG 178
910101115
Used to crimp the crimp ring to Mini Coax contacts.
-
product
Tool, Crimp, Micro Coax, Receiver and ITA
910101131
Used to crimp micro coax contacts to RG178 wire.
-
product
Tool, Crimp, Micro Coax, Receiver and ITA
910101132
Tool Kit, Crimp, Micro Coax, f/ RG 316 and RG 179 wireIncludes p/n's 910101139, 910101135, 910101133.Used to crimp VPC micro coax contacts to RG316/179 wire. Includes receiver, ITA and crimp die.
-
product
Copper, Type T (°C) Contact
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
