Crimp
-
Product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Ferrules, 1m
40-972-009-1m-MU
-
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, 22-28 AWG, 50µ” Au, Crimp
610138116
-
*Please note: The difference between this p/n and 610138216 is the amount of gold plating. See below.P/n 610138116- 50µ" AuP/n 610138216- 30µ" AuPrimary mating contact 610138112. (May mate with other ITA contacts, as well.)
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Ferrules, 0.5m
40-972-015-0.5m-FU
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Assembly & Test Services
-
Once piece parts have been manufactured, skilled operators can kit or assemble them to the desired level. Our wiring technicians are trained to IPC standards of workmanship and operate within ESD controlled areas. We carry out both solder and crimp wire terminations along with integration of electronic components such as fans, PCBs and power supplies.
-
Product
Tool, Kit, 75 Ohm Coax, ITA, Cable Install
910102107
-
Consists of 2 tools for installing cabling into the contact. Crimp Tool and Locator for center contact and Hex Crimp Tool for outer shield (p/n# 910104139).
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Ferrules, 1m
40-972-015-1m-MU
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
3 ft Coax Wire with a Coax Pin
GX96411
-
One 3 ft Coax Wire with a Coax Pin Crimped on One EndRequires the GX96409 connector housing.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Ferrules, 1m
40-972-025-1m-MU
-
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
40-972-025-0.5m-MU
-
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Ferrules, 0.5m
40-972-009-0.5m-MU
-
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Receiver, I2 Micro ICon, 120/12 Position Hybrid, For Crimp Contacts
310130105
-
The i2 Micro iCon receiver is a one piece connector capable of holding up to 120 Signal QuadraPaddle contacts and 12 Micro Coax or Micro Power. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is made for crimp contacts. Accessories such as keying pin kits, protective covers, and strain relief are available.
-
Product
Cable Assembly, 26-Pin D-Type, Female to Unterminated With Ferrules, 2m
40-972-026-2m-FU
-
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Signal, Module, ITA, i2 MX, 84 position, QuadraPaddle, Crimp
510144002
-
Signal, Module, ITA, i2 MX, 84 position, QuadraPaddle, Crimp
-
Product
160-Pin DIN41612 Connector, Crimp Pin, Female
92-960-160-F
-
Suitable for users to create their own cable assemblies, this product can be supplied with or without the backshell. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the connector can be fitted with an optional screwlock assembly.
-
Product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp only
610110101
-
Primary mating contact 610110108. (May mate with other ITA contacts, as well.)p/n 610110125 TriPaddle Receiver 50µ" AU plating.p/n 610110101 TriPaddle Receiver 30µ" AU plating.
-
Product
Mating Coax Connector And 20 Coax Pins Crimped (One End) To 3 Foot Wires
GX96404
-
Mating Coax Connector and 20 Coax Pins Crimped (One End) to 3 Foot Wires
-
Product
Wire Crimp Pull Tester (Manual)
WT3-201
-
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
Product
Copper, Type T (°C) Contact
-
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
Product
Cable Assembly 44-Pin D-Type Female to Unterminated With Ferrules, 2m
40-972-044-2m-FU
-
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Coax, Contact, ITA, 20 GHz, RG 223, Crimp, 90 Series Modules only
610102117
-
Primary mating contact 610102116. (May mate with other ITA contacts, as well.)20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps.It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.
-
Product
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp
510143002
-
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp.
-
Product
Chromel, Type K (°C), Thermocouple Contacts
-
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
Product
KIT for Test Cable Networks with Tools and Accessories
1RA370
-
Include: *Multi network cable tester for RJ45 (UTP / STP) and BNC*Modular crimping tool*LSA insertion tool*Cable stripper and cutter*30 units of RJ45 (8p8c) modular plugs*30 units of RJ11 (6p6c) modular plugs*24 units of colour strain relief*Comonents pocket*Zipper vinyl case
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 1m
40-972-037-1m-MU
-
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
Fiber Optic Terminus
ARINC 801
-
The ARINC 801 fiber optic terminus is the next generation of high density, butt joint interconnect technology. With its standard 1.25 mm ferrule and sleeve, the ARINC 801 terminus is designed for both multimode and single-mode applications. For the pull-proof design, the cable jacket is crimped on an external body and a floating mechanism avoids any loss of performance when pulling on the cable. This feature allows for the use of the connector without a backshell. Standard connector formats include MIL-DTL-38999 type, MIL-DTL-83527 type, ARINC 600 and ARINC 781.
-
Product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 2m, HV
40-972-009-2m-FU-HV
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
160-Pin DIN41612 Connector, Crimp Pin, Female, 90º
40-960-160-FT
-
Suitable for users to create their own cable assemblies where a 90 degree down cable exit would be preferred. If the user requires the connector to have a second fixing then it can be fitted with an additional screwlock assembly 40-969-101 where applications permit.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Ferrules, 16A, 0.5m
40-972C-020-0.5m-FU
-
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
