Showing results: 406 - 420 of 451 items found.
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
Fairview Microwave Inc.
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
PGY-SSMlite SD -
Prodigy Technovations Pvt. Ltd.
PGY-SSMlite SD Protocol Analyzer is the most feature rich comprehensive Protocol Analyzer available to capture and debug SD protocol data. PGY-SSMlite Protocol Analyzer supports SD, Protocol analysis for wide data rate up to 200MHz SDR mode (UHS-I). The innovative active probe has minimum electrical loading on device under test (DUT) and allows the protocol data capture without affecting the performance DUT. PGY-SSMlite protocol analyzer allows industry first continuous streaming of protocol data from PGY-SSMlite Protocol Analyzer to host system (using USB3.0 or GbE interface). Comprehensive decoding of data, protocol tests, and error analysis enables verification of communication of SD host and device.
-
OPTOWERE-S100 (Fiber Optic Test System) -
Notice
The frame of FOTS system consists of the Main control part and the Slot mounting part. The Main control part is in charge of control and interface of the system and the Slot mounting part can hold up to maximum 8 slots, which are modularized according to each function and come out in five kinds. This integrated test system is designed to help manage the test and measurement related to optical communication and component. And the modular architecture of FOTS allows for customized configuration so that the slot of LD Driver, 2 channel VOA, 1 X 4 switch, WDM EDFA and C + L – Band ASE Source can be chosen according to user’s necessities. Main control part and each function module are run by effective and multi-functioned system control program in the base of high speed remote interface, GUI display and the discriminative high speed driving of module and system. This system can provide variety manufacturing and laboratory applications such as general quality test and reliability test of optical component and optical signal transmission test through efficient linkage with other system.
-
JGB Consulting, Inc.
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
Dragon -
Excalibur Systems, Inc.
Excalibur’s Dragon is an advanced, ruggedized PC104 and PC104+ system in an enclosed, modular casing. The system is appropriate for use in data acquisition, recording nd control for any combination of ARINC-429, MIL-STD-1553, Serial, Discrete or similar types of communication. The modular, stack through design of the PC104/PC104+ platform allows you to build a tailor-made configuration based on Excalibur’s extensive range of boards plus any 3rd party cards of the customer’s choosing. Our engineers will integrate and test all 3rd party cards to the customer’s specification.
-
778768-04 -
NI
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
PXI-5670 / 778768-01 -
NI
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
778768-02 -
NI
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
PXI-5670 / 778768-03 -
NI
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
LP Technologies
LPT-3000 Portable Spectrum AnalyzerThe LP Technologies LPT-3000 Spectrum Analyzer is a fully synthesized RF Spectrum Analyzer featuring simple user controls which allow the novice or the seasoned expert to use the LPT-3000 right out of box. The LPT3000 provides you with a powerful RF test and measurement tool for CDMA and WCDMA RF systems, broadcast RF systems, EMI/EMC. The features include 6.4 color display, centronics printer, internal memory, USB host, built in CDMA measurement (ACP, Channel Power and Occupied bandwidth). The LPT 3000 Spectrum Analyzer gives educational institutions, mobile and communication system manufactures and RF product service centers a quality RF test instrument at an unbelievably affordable price.
-
446 -
SCI
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
CRY2301 -
CRYSOUND
CRY2301 Noise sensor is a new type of noise test equipment independently developed by CRY Sound for industrial grade applications. It can realize real-time noise time domain and frequency domain analysis with real-time spectrum analysis software. The product complies with such standards as IEC61672 (Class 1) and GB/T3785 (Class 1). CRY2301 integrates measurement microphone, preamplifier, data acquisition, and data communication in a compact structure. It supports an optional 1'' high-sensitivity microphone for extremely low sound pressure testing. CRY2301 uses a USB interface for data communication and power supply. As a composite USB device consisting of a USB Audio device and a HID device, it is compatible with 32-bit/64-bit Windows 7 and Windows 10 systems. CRY2301 is equipped with real-time spectrum analysis software for easy access to time and frequency domain measurements. The real-time spectrum analysis software supports frequency weighting and time weighting, and can perform acoustic analysis, such as noise statistical analysis, octave analysis, and FFT analysis.
-
BVR Series -
IBEKO Power AB
Battery voltage recorders from BVR series are designed to serve as a support tool for cell voltage measurement during battery capacity testing.During capacity testing, cell voltage, temperature, inter-cell connection voltage, and specific gravity should be measured in order to determine failling cells in the string that should be replaced.Furthermore, IEEE standards for stationary batteries applications stipulate periodical measurement of overall string voltage, as well as cell voltage and temperature.The BVR Series is the perfect tool for that purpose. All measurements are automatically saved in device’s internal memory. Additionally, DV-B Win software helps the user to download all measured results. Furthermore, the user can create test reports and export them to various formats.BVR series includes two models: BVR11 and BVR22. These are rechargeable handheld devices intended for performing monthly battery inspections and support tools during capacity testing. The list of the applications of these instruments includes:Efficient supplement to BLU series of battery load units during battery discharge testingMonthly inspections of large battery banksAmbient temperature measurementCurrent measurement using current clampsUSB and Bluetooth communication with PCSimultaneous string voltage and current measurement to analyze a discharge test processThe BVR22 model provides Bluetooth communication with an external density meter, for transferring electrolyte specific gravity and temperature readings.
-
Windfreak Technologies, llc
Windfreak Technologies provides high value radio frequency devices such as RF Signal Generators, RF Synthesizers, RF Network Analyzers, RF Power Detectors, RF Mixers, and RF Frequency Converters. These devices can be used as RF Test and Measurement Equipment and controlled by Labview in an Automated Test Equipment (ATE) setup, or used as bolt-in RF modules in RF communications equipment. All products have innovative, powerful feature sets controlled by internal microprocessors so any settings can be memorized and used with or without a PC. Windfreak hardware also comes with the Labview GUI source code saving the end user hundreds of hours programming custom software. Use one of our RF Signal Generators or other products risk free. Return it if you dont like it.
