Combustion
-
Product
Needle Flame Combustion Tester
-
Shanghai Dean Electrical Co., Ltd
The touch screen control needle flame combustion tester is developed according to the requirements of the needle flame combustion test in the standard
-
Product
Dual Pitot Tube Flow Meter
PTFM-ONE-DT
-
The Dual Pitot Tube Flow Meter, PTFM-ONE DT is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers, with a sampling rate of 1kHz to accurately measure highly pulsating exhaust flows. This rapid capture rate ensures that any pulsations or exotic behaviour caused by the engine is measured, and the unique design of the PTFM-ONE DT means reverse flows can be calculated, with the same guarantee of sensitivity.
-
Product
Residential/Commercial Combustion Analyzer Kit w/ Pressure/Printer
C163KIT
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C163 Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to included printer and is wireless to a free printer App. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
Flame Burning Tester
DRK3024A
-
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
Product
TOC Combustion Analyzer
Torch
-
The Torch is considered the premium TOC combustion analyzer due to its many useful features and automated analysis processes. For example, it makes serial dilutions of stock standards to form a calibration curve and auto-dilute samples with concentrations above the calibration curve. The Torch software has built-in diagnostic and troubleshooting capabilities. For a luxury but affordable TOC combustion analyzer that you can just load and walk away, look no further than the Torch. You won't regret it!
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
PCIe Gen3 4K Compact, High Speed Camera for Testing
CB120MG-CM-X8G3
-
4K, compact, high speed camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
Product
N/Protein Analysis
-
Elementar Analysensysteme GmbH
The determination of the total protein content is an essential tool for quality control and protein declaration according to international labeling laws in the food & feed industry and research facilities. Since the protein content can directly correspond to product properties, highly precise, matrix-independent protein analyses are required in all application areas.Our N/protein analyzers use the high-temperature combustion method according to Dumas, which has clear advantages over Kjeldahl regarding laboratory safety, sample throughput, labor time, amount of chemical waste and thus cost-per-analysis. Our analyzers for the determination of nitrogen and protein are dedicated instruments serving today’s customer needs in regards to price-per-sample, throughput and sensitivity.
-
Product
Rubber Testing Equipment
-
Dongguan Amade Instruments Technology Co., Ltd
Rubber testing equipment are used to test the physical properties, chemical properties, thermal properties of uncompounded and compounded rubbers at prescribed conditions to help manufactures or researchers in comprehending the characteristics, updating the formula and improving product quality. Including volatile component, ash content, Mooney viscosity, vulcanization curve, Mooney scorch time, hardness, tensile properties, tearing, the compression performance, impact, friction resistance, fatigue resistance, peel strength, vertical & horizontal combustion, smoke density, limiting oxygen index, the flame spread rate, the surface resistance, surface resistivity, volume resistivity, the breakdown voltage, dielectric strength, dielectric loss, antistatic properties, Aging test (UV, Xenon lamp, carbon arc lamp, ozone) etc.
-
Product
Gas Monitor
S5000
-
The General Monitors S5000 Gas Monitor is the ultimate gas detector for extreme environments needing to detect oxygen, toxic and combustible gases.
-
Product
Glow Wire Tester
-
Shanghai Dean Electrical Co., Ltd
Glow wire tester would stipulate material (Ni80 / Cr20) and the shape of the heating wire (4 mm Φ nichrome wire) in large current heated to test temperature (550 ℃ ~ 960 ℃, after 1 mi to specified pressure (0.95 + / - 0.1 N) vertical burning hot try 30 s, inspect goods and bedding content whether light-off or the burning time to determine the fire risk of electrical and electronic equipment finished product;Determination of ignitability, ignitability temperature (GWIT), ignitability and ignitability index (GWFI) of solid insulation materials and other solid combustible materials is also applicable to the industries of insulation materials, engineering plastics or other solid combustible materials.
-
Product
RH850 Family (Automotive only)
RH850/E2x
-
RH850/E2x microcontrollers are ideal for powertrain applications, have high operation processing performance for realizing new combustion systems for fuel-efficient engines, and built-in hardware for knock control such as a successive approximation A/D converter, delta-sigma A/D converter, cyclic A/D converter, Digital Filter Engine (DFE), and Advanced Timer Unit (ATU-V), and engine control such as fuel injection control.
-
Product
Total Halogen and Sulfur Analyzer
XPLORER-TX/TS*
-
The XPLORER-TX/TS is a microcoulometric combustion analyzer for the analysis of total halogens and total sulfur. The small footprint allows it to blend into every laboratory environment, whether it is in R & D, refinery, chemical, or petroleum applications. This next generation analyzer surpasses all others in its class in performance. It is robust, precise and ideal for harsh testing environments.
-
Product
Calorimeters
-
Operators in refineries are looking for fast, reliable fuel gas and flare gas combustion measuring solutions that control the air/fuel ratio to minimize disturbances and maximizes the efficiency of the combustion process. Our COSA Xentaur portfolio of calorimeters for fuel and flare gas combustion measure Wobbe Index, heating value (BTU) and the Combustion Air Requirement Index (CARI). Our COSA 9610™ calorimeter provides a fast and accurate measurement of Wobbe Index, Heating Value and Combustion Air Requirement Index (CARI).
-
Product
Carbon / Sulfur Analyzer
ELEMENTRAC CHS‑r
-
The ELEMENTRAC CHS-r elemental analyzer determines the elements carbon, sulfur and hydrogen by combustion of the sample in an oxygen stream and subsequent measurement of the combustion gases CO2, SO2 and H2O in selective infrared measuring cells. A high sample weight of up to 500 mg ensures excellent reproducibility of the measurement results, even for heterogeneous samples.
-
Product
Combustion Leak Tester
AC560000
-
Fast, economical and accurate method to test for combustion gas leaks in head gaskets, cylinder heads and engine blocks. Dual chamber design provides more accurate test results. Test fluid can be used for both gasoline and diesel engines.
-
Product
Elemental Analyzers for Carbon, Sulfur, Oxygen, Nitrogen and Hydrogen
-
HORIBA Scientific provides inorganic elemental analyzers for a wide range of applications based on the inert gas fusion technique and high frequency heating combustion in oxygen stream.The EMIA Series for Carbon and Sulfur analysis and EMGA Series for oxygen, nitrogen and hydrogen analysis strongly rely on HORIBA’s experience as a pioneer in Non-Dispersive Infrared (NDIR) technology. Both EMIA and EMGA designs meet all requirements for the metallurgical industry. These instruments also help scientists working in other application fields such as semiconductor, battery materials, ceramics and more.
-
Product
PCIe Gen3 4K at 500 Fps High Speed Compact Camera for Testing
CB160CG-LX-X8G3
-
4K at 500 Fps High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
Product
Mill & Silo Monitoring System
MSM-100
-
MSM-100 is a monitoring system specifically designed to continuously detect carbon monoxide(CO) in pulverizing mills. The high level of CO produced by any incomplete combustion process, is used by the MSM-100 system as advance warning of a mill fire. It is suitable for any coal or peat system where advance warning of spontaneous combustion is required. MSM-100 is intended for operation in the electricity, metals, cement, steel and processing industries.
-
Product
Pen Style Combustible Leak Detector
UTLCD1
-
UEi Test & Measurement Instruments
The UTLCD1 is a professional value Combustion Leak Detector with easy one step operation.
-
Product
Combustion Efficiency Analyzer
CEA-100
-
Walsn CEA - 100 combustion efficiency analyzer is designed to continuously monitor CO content in flue gas while the measurement data can be used to adjust the ratio of fuel/ air so as to achieve the maximum boiler efficiency for boiler operation. Walsn CEA - 100 adopts the dual-measuring-sensor technology and features high accuracy with low zero drift and very small failure rate, matching the requirements of the harsh industrial environment. It is also easy to install and maintain.
-
Product
Optical Oxygen Sensors
-
The analyzer is suitable for direct field installation (NEMA 4X) in hazardous area (Class I, Division 2). The optical fiber sensor platform allows small inline sensors to be installed into sample tubing lines (1/4”), flow cells using NPT fittings, or directly into tanks or process lines using our retractable “hot tap” sensor design. BOS optical oxygen sensors are impervious to typical O2 poisons (H2S) and interferences (combustibles, magnetic, CO2 and H2) with high accuracy and long-term stability measurements without the need for complex or advanced sample conditioning systems. The threaded version of the optical sensor has optional Dual Seal (ANSI/ISA 12.27.01) classification for high pressure applications up to 1200 PSIG (82.7 BAR).
-
Product
Solid State Gas Detectors
SMC 20X/200X
-
The SMC 20X/200X are single-gas detectors used to monitor combustible gas, hydrogen sulfide (H2S) or carbon monoxide (CO). The detectors are based on solid-state technology, a simple and robust method of detection capable of detecting low parts-per-million (ppm) levels of gas.
-
Product
Automated Engine Testing System
-
Automated engine test system is intended for comprehensive testing of electrical motors with shaft rotation frequency up to 70 000 rpm. Such engines include:*high-voltage motors;*traction engines;*internal combustion engines;*AC motors;*DC motors;*synchronous engines;*asynchronous engines;*asynchronous engines with short-circuit rotor.
-
Product
Open Path Combustible Gas Detector
SafEye (Quasar 900)
-
Teledyne Gas & Flame Detection
The Open Path Combustible system detects hydrocarbon gases by analyzing the absorption of radiation caused by gases in the atmosphere and comparing it to background atmospheric absorption. This is accomplished between a pair of units: a Flash Source and a Detector that can monitor a distance of up to 200 meters.Open Path Combustible Gas Detectors are robustly designed and can handle the toughest environments: 316L stainless steel housings that meet IP66/IP68 and NEMA 250 6P egress standards; circuit boards epoxy coated for protection; MIL-C-810C testing for humidity, salt, fog, vibration, mechanical shock and temperature extremes; and SIL-2 approval per IEC61508 is a final statement in reliability.
-
Product
UL94 Combustion Chamber, IE60695vFlammability Tester
CX-S16
-
Shenzhen Chuangxin Instruments Co., Ltd.
Horizontal Vertical Flame Tester is a comprehensive test instrument whick strickly designed according to Standard IEC60695, GB5169, UL94 and can meet the relative standard's requirements. It's mainly used to test the flammability of plastic and other nonmetalloid parts specimen to evaluate fire hazardous degree of accidental burning caused by the material.
-
Product
Monicon Gas Monitors
-
Monicon Gas Monitors are innovative, cost-effective, wall and rack mounted units, with the ability to monitor single or multiple channels. Before ordering, customers can select from a range of toxic gases, combustible gases and oxygen, for monitoring in a wide range of applications.
-
Product
Industrial emissions Analyzers
-
When it comes to the analysis of emissions and industrial precision, combustion and reliability are two essential concepts. Seitron analysers can be used in all contexts in which it is necessary to measure and document emissions in accordance with applicable regulations.
-
Product
High Performance Isotope analysis of LC Separated Compounds
Iso CHROM® LC
-
Elementar Analysensysteme GmbH
Unlike the existing LC-inlet solution via chemical oxidation, the iso CHROM LC works with high-temperature combustion. It quantitatively converts organic carbon to CO2.In addition, the easy-to-use iso CHROM LC shows outstanding precision, accuracy, and linearity without significant peak broadening that can diminish the chromatographic performance. In continuous operation, virtually all peaks in a chromatogram can be analyzed for the stable isotope ratios of carbon.
-
Product
Combustion Enginee Analyzer
-
Internal Combustion Engine Measurement, Analysis and ThermodynamicsComplete combustion measurement and analysis system for internal combustion engine research and development, optimization and testing of ignition systems, exhaust systems, and valve control gear.
