Combustion
-
Product
Residential/Commercial Combustion Analyzer Kit w/ NOx Sensor/ Oil-Fired Appliances/ Printer
C165+NOILKIT
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
Single Gas Sensor
Z-Gard® S MPO
-
The Z-Gard S MPO Gas Sensor connects directly to a building automation system for single gas monitoring solutions. It detects the presence of either carbon monoxide, nitrogen dioxide or combustible gases in air.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Opacity Monitor
DT109
-
The Datatest Model 109 is a microprocessor based non-compliance opacity monitor for process, baghouse, combustion and OSHA applications. The micro controller provides excellent accuracy, reliability and stability with features such as push button calibration, path length correction and averaging.
-
Product
Combustible and Toxic Gas Detection
IMR IX616
-
IMR Environmental Equipment, Inc.
It has a high-quality sensor, and uses natural diffusion as the method for detection. It has high sensitivity and reproducibility. It also uses an embedded MCU controller and is easy to operate. The shell has special high strength anti-slip rubber it is water-proof, explosion-proof and dust-proof. It has alarms that are visual, audible, and with vibration.
-
Product
Tubular Infrared Carbon and sulfur Analyzer
8510-CS
-
Wuxi Jinyibo Instrument Technology Co., Ltd.
Determination of elements: carbon and sulfur combined measurementAnalytical principle: tube furnace combustion infrared absorption method detectionAnalysis range: carbon: 0.0010%-10.000% ( expandable to 99.9999%) Carbon: 0.0005%-0.500% ( expandable to 99.9999%)Analysis error: carbon: in line with GB/T223.69-1997 standard sulfur: in line with GB/T223.68-1997 standardAnalysis time: 20-100 seconds adjustableElectronic balance: not quantitatively weighed, weighing range: 210g/0.001g
-
Product
Residential Combustion Analyzer w/ AC509 Carrying Case
C161C
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C161 Residential Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and now adds a heat exchanger test. Prints to optional printer. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
Horizontal & Vertical Combustion Tester
-
Shanghai Dean Electrical Co., Ltd
Test instrument for testing the combustion performance of plastics and non-metallic materials.Applicable to the laboratory method for determination of horizontal or vertical combustion performance of samples of plastic and non-metallic materials under 50W flame conditions.(the real object is like the picture on the right)
-
Product
Gas
-
For toxic and combustible gas, as well as refrigerant leak detection, ACI’s line of gas sensors will solve the most challenging applications with the fewest devices and lowest total installed cost
-
Product
Solid State Gas Detectors
SMC 20X/200X
-
The SMC 20X/200X are single-gas detectors used to monitor combustible gas, hydrogen sulfide (H2S) or carbon monoxide (CO). The detectors are based on solid-state technology, a simple and robust method of detection capable of detecting low parts-per-million (ppm) levels of gas.
-
Product
Open Path Combustible Gas Detector
SafEye (Quasar 900)
-
Teledyne Gas & Flame Detection
The Open Path Combustible system detects hydrocarbon gases by analyzing the absorption of radiation caused by gases in the atmosphere and comparing it to background atmospheric absorption. This is accomplished between a pair of units: a Flash Source and a Detector that can monitor a distance of up to 200 meters.Open Path Combustible Gas Detectors are robustly designed and can handle the toughest environments: 316L stainless steel housings that meet IP66/IP68 and NEMA 250 6P egress standards; circuit boards epoxy coated for protection; MIL-C-810C testing for humidity, salt, fog, vibration, mechanical shock and temperature extremes; and SIL-2 approval per IEC61508 is a final statement in reliability.
-
Product
Explosion Proof Area Hydrogen Monitor
HY-ALERTA™ 2620
-
H2scan’s 2620 Explosion Proof Area Hydrogen Monitor provides hydrogen-specific leak detection and measurement for hydrogen concentrations as low as 4000 ppm and can be scaled to any concentration up to 5% hydrogen by volume, a range representing 10% to 125% of hydrogen’s low flammability limit. The monitor is designed for either ceiling or wall mount. H2scan’s hydrogen-specific sensor technology has no cross sensitivity to other combustible gases, thus eliminating false positive alarms and ensuring safety system reliability.
-
Product
Residential/Commercial Combustion Analyzer Kit for Oil-Fired Appliances /Printer
C165+OILKIT
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
Analyzer for Solution for Measuring Sulfur in Liquid Applications
SLA-1000
-
The ATOM SLA-1000 is an online process analyzer utilizing patented Excimer UV Fluorescence (EUVF) Technology to measure Total Sulfur in Liquid in a variety of refinery process applications.ATOM Instrument offers the most versatile Total Sulfur analyzers available. The ATOM SLA-1000 has the fastest analysis time of any commercially available analyzer allowing user-defined , multiple cycle averaging to improve analyzer performance. The analyzer operating software is both intuitive and user-friendly. In addition, the SLA-1000 requires only bottled air (no other gases needed for carrier or combustion) during normal operation and does not require installation in a shelter.
-
Product
Total Organic Carbon Measurement
-
Total organic carbon (TOC) measurement is a well-established technique that provides valuable information about water quality for process control and regulatory compliance. Around the world, people have relied on our instrumentation for fast, accurate results for over 45 years. Our Total Organic Carbon (TOC) portfolio includes the 1080 Combustion TOC Analyzer, the 1030W Wet Oxidation TOC Analyzer, and the 1030D Dual Mode Analyzer – all of which are individually designed to help laboratories maximize efficiency.
-
Product
CS/ONH-Analysis
G4 ICARUS Series 2
-
The combustion analyzer G4 ICARUS Series 2 with high frequency (HF) induction furnace and HighSense™ detection sets new standards in for a rapid and precise carbon (C) and sulfur (S) analysis in inorganic solids.
-
Product
Combustible Gases
-
UEi Test & Measurement Instruments
Designed to detect combustible gas leaks
-
Product
Fixed Gas Detectors
OLCT 10 - OLC 10
-
Teledyne Gas & Flame Detection
The OLC 10 and OLCT 10 are designed to detect combustible or toxic gases for tertiary applications (boiler plants, battery charging rooms, car parks, hospitals). Two OLC 10's can be connected to one detection channel to monitor the same area, without an additional junction box or extra wiring. Similarly, up to five OLCT 10's can be connected to one channel for the detection of CO, NO or NO₂ in a car park application. Easy to install and operate, these detectors combined with the MX 16 control unit meet demanding user requirements.
-
Product
Multi-Stage Injection Analyzer
FJ-8000 series
-
Common rail method already is commonly known as an injection system of diesel engine now. That system enables multi-stage fuel injection by offering high injection pressure in various driving situation. Adopting the common rail system helps improving fuel consumption, reducing noise and vibration, because the system can make the fuel approximate complete combustion which suppresses PM and NOx generation. FJ-8000 series is the multi-stage injection analyzer that supports more accurate injection by measuring injection quantity, injection rate, injection timing, and injection period by multi-stage injection of common rail system in the environment that is near to an actual vehicle environment.
-
Product
Pitot Tube Flow Meter
PTFM-1000V2
-
The Pitot Tube Flow Meter, PTFM-1000V2 is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers to accurately measure highly pulsating exhaust flows with a sampling rate of 1kHz. This rapid capture rate ensures that any pulsations or exotic behaviour in an engine is measured, and the unique design of the PTFM pitot tube means reverse flows can be measured with the same guarantee of sensitivity. The interface can be run standalone with a laptop, or seamlessly integrated to run alongside an analyser system without adding any more steps to the test cycle process.
-
Product
Test and Check Kit w/ DL469/ CD100A/ EM152/ PDT550
TACK10
-
UEi Test & Measurement Instruments
Convenient Test and Check Kit, for quick testing, includes True RMS Clamp meter, Combustible leak detector, Dual input manometer, NSF waterproof thermommeter, Carrying case
-
Product
Telecom Gas Monitors
SMC 2350/2360
-
The SMC 2350/2360 Telecom Gas Monitors both continuously monitor for the presence of Carbon Monoxide (CO), but the Model 2360 also monitors for combustible gases.
-
Product
Residential/Commercial Combustion Analyzer Kit w/ Printer
C165+KIT
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
Boroscopes
-
A Borescope is an optical tool used to view invisible areas without damaging an item.Borescopes are used for many devices in the industry. Hence its many benefits for example Turbine Engines,Internal Combustion Engines =,Pipes,Heat exchanger tubes,Gear boxes, and more.
-
Product
Flue Gas Analyzer (Instrument Only)
C160
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C160 Residential Combustion Analyzer is instrument only, easy to use with a rugged design, multiple sensor protections and altitude compensation. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
Flammability Test Chamber
-
Shenzhen Bonad Instrument Co., Ltd.
BONAD’s flammability test chamber complies with IEC 60950, IEC 60695, IEC 60112, IEC 60332 and other standards. We not only provide standard wire and cable combustion test equipment and leakage tracking test equipment and other electrical test equipment as well as a variety of different combustion test equipment, but we also provide customization and can develop professional and high-quality test equipment according to test requirements. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
PCIe Gen3 Full HD, High Speed, Compact Camera for Testing
CB019CG-LX-X8G3
-
Full HD, High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
Product
Hazardous Locations Product Testing
HazLoc
-
F2 Labs can assist you with your hazardous location testing needs. We can perform the HazLoc product testing required to ensure that your product won’t cause a fire or explosion in an area where flammable or combustible materials (such as dusts, gases, fibers or vapors) are present. The product must be designed using various methods of protection.
-
Product
Combustion Analysis
-
The Phoenix family provides combustion analysis solutions for both in-cell and in-vehicle testing.
-
Product
High Temperature Thermometer
SensyTemp TSH200
-
High temperature combustion, annealing and melting processes are usually executed without pressure at temperature up to 1800 °C (3272 °F). As a result, the selection of the appropriate thermowell is the greatest challenge for temperature measurement.
