-
product
DC/DC With UPS And Charge Controller
PCM-PS402-512
WINSYSTEMS’ PCM-PS402-512 is a wide input range, triple output PC104 DC/DC converter with a built-in battery charger and uninterruptable power supply (UPS) controller. Designed for harsh environments, the power supply operates from -40° to +85°C without a fan or heatsink making it ideal for industrial applications.
-
product
Quartz Charge Force Rings
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load.
-
product
In-line ICP® Charge Converters
In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.
-
product
Charge Integrator Amplifiers
AD8488
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
product
Accelerometer (Charge Output Type)
NP-2000 Series
This sensor converts mechanical vibrations into electric signals in proportion of vibration acceleration.You can choose the one that is ideal for your purpose,conditions,applications etc. from wide variety of selection.Charge amplifier is necessary because it is a charge output type,however, compared to pre-amplifier built-in type, it can be used at higher temperature in general.
-
product
CTEK MUS 4.3 TEST&CHARGE Battery Charger and Tester
56-959
The MUS 4.3 TEST&CHARGE combines an advanced micro-processor controlled battery charger with a battery and alternator test function to provide the ultimate in battery testing, charging and maintenance.
-
product
20-50,000 Hz Charge Amplifier
203G8
The Trig-Tek™ 203G8 accepts pickupswith sensitivities varying from 1 to 110pC/g. It has three simultaneous outputs:Acceleration with a sensitivity of 100 mVrms/Pk g; Velocity with a sensitivity of 534mVrms/Pk/ips; and Displacement with asensitivity of 100 mV/mil DA.
-
product
Battery Charge and Discharge Tester
HTCFDK / 791
Wuhan Huatian Electric Power Automation Co., Ltd.
The voltage monitoring information of single battery is simple, safe and accurate with wireless relay access.
-
product
Programmable USB Hub with 4 Charge Ports
The USBHub2x4 is a programmable USB 2.0 compatible hub featuring 4 device downstream ports with standard USB type-A receptacles and each port is capable of delivering up to 2.5A simultaneously. With two host (upstream) connections using usb mini-B connectors, the USBHub2x4 is perfect for environments where multiple devices need to be shared or switched between two host computers. E.g.: software regression testing, iPhone software development and validation, Android software development and validation, USB device regression testing, manufacturing testing, device burn-in testing and USB device charge-curve testing.
-
product
In-Line Charge Amplifiers
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
product
Periodic Verification System for Measuring Static Charges and Verifying Ionizer Performance
STME-PVS
Statclean Technology (S) Pte Ltd
This meter is designed to measure static charges and to verify ionizer performance. It consist of three components- an Electrostatic Fieldmeter, a Detachable Plate and a Charger.
-
product
Battery Charge and Discharge Tester
HTCFD / 790
Wuhan Huatian Electric Power Automation Co., Ltd.
The voltage monitoring information of single battery is simple, safe and accurate with wireless relay access.
-
product
Charge Converter
CH-6130/6140
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
product
Dual Digital Aquisition System For Charge Integration And Pulse Shape Discrimination
DT5790
The DT5790 operates upon the DPP-PSD firmware, specially developed for Charge Integration and Pulse Shape Discrimination. DPP-PSD is based on an advanced on line Digital Dual Gate Charge Integration allowing an effective data analysis even at high count rate. It performs input signal baseline calculation, self-triggering and double-gate charge integration with programmable parameters, double integration of both prompt and total charge for Pulse Shape Discrimination and pedestal subtraction for energy calculation.
-
product
Charge Coupled Device (CCD) Image Sensors for Space and Ground-Based Astronomy
(CCDs) for Space science, Ground-based Astronomy, and Earth observation applications with an impressive record of successful deliveries to a wide range of customers over 40 years.All Teledyne e2v devices can be supplied partially or fully customised to fit the application and achieve the best possible system performance. CCD image sensor design, manufacture, test and characterisation are carried out in-house enabling control from start to finish. Multi-polysilicon, multi-metal and back-illumination options are available for high resolution, high sensitivity and very low noise.
-
product
DC/DC with UPS and Charge Controller
A wide input range, quad output PC/104-Plus DC/DC converter with a built-in battery charger and uninterruptable power supply (UPS) controller. Designed for harsh environments, the power supply operates from -40 to +85C without a fan or heatsink making it ideal for industrial applications.
-
product
Static Charge Event Detector / Data Logging System
EV-10A
Tokyo Electronics Trading Co., Ltd.
EV-10A detects ESD (Electro-Static Discharge) and records them in a PC. ESD sensitive electronic components increase rapidly. If electro-static charge is not strictly controlled in the production line of these components or in the assemble line using them, the yield will be decreased.
-
product
Test Line • Devices for measuring electrostatic charges
HAUG offers a wide selection of easy-to-use gauges. These are field charges with which electrical charges, fields and potential can be measured. The measured values show how strongly a surface is covered with an electrostatic charge.
-
product
Charge Pumps
Renesas offers monolithic CMOS voltage conversion ICs that perform supply voltage conversions from positive to negative for an input range of 1.5V to 12V, resulting in complementary output voltages of -1.5V to -12V.
-
product
Space Charge Measuring Equipment
PEA
The increasing request for energy quality and, thus, insulation system reliability, associated with significant steps in the manufacturing of new insulating materials, are pushing strongly the research on new techniques for the diagnosis of insulation ageing.
-
product
Dual-Mode Charge Amplifiers
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
product
High Temperature Charge Mode Accelerometers
Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).
-
product
Charge Amplifier
This compact Charge Amplifier has 3 signal routes.When it is used as the Charge Amplifier for the vibration analysis systemWave Stocker, all setups are possibleby the upgraded software.
-
product
Charged Plate Monitor
Model 157
Trek's Model 157 Charged-Plate Monitor offers greater accuracy, stability and bandwidth than conventional designs. This model combines Trek's patented precision charge measurement capability with features that drive down the cost of ionizer performance testing and maintenance. Model 157 is suitable for semiconductor, disk drive, LCD and many other manufacturing environments that are sensitive to static charge.
-
product
Battery Charge Discharge Tester
KV Hipot Power Test Equipment Co.,Ltd
Battery Charge Discharge Tester is a multi-function comprehensive tester which is not only a battery charger and Battery discharger, but a battery activator.
-
product
Charge Amplifier
ZET 440
Charge amplifier ZET 440 for piezoelectric detectors is intended for:*amplification and conversion of output signals of primary piezoelectric transducers with charge output;*amplification and conversion of output signals of primary transducers with the IEPE type in-built electronics to voltage;*gain ratios: 1, 10, 100;*LPF: 0.1, 1, 10 Hz
-
product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
product
Battery Charge & Discharge Test System
ITS5300
ITS5300 battery charge and discharge test system is designed for a variety of power batteries (lead acid, nickel hydrogen, lithium batteries, super capacitors, hydrogen fuel cells, etc.) for performance testing.
-
product
Repeated Charge Discharge Test Set
The IS 13341 : 1992 has laid down the requirements for Ageing Test, Self-Healing Test and Destruction Test on Shunt Capacitors of the self healing type for AC Power Systems. The Ageing Test is to be performed at a specified voltage of 1.25 times the rated voltage for 750 hours. The test is to be followed with a repeated discharge cycle test which involves charging of the capacitor to a DC voltage and discharge of the same through an Inductance. Sivananda Electronics has developed this equipment for the benefit of capacitor manufacturers, for the first time in India.
-
product
Endevco Cryogenic Charge Output Accelerometers
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperatur...show more