Similar Topics: Cable Assembly
Cable Assemblies
enable IO signal paths.
See Also: Cables, Interconnects, Flying Leads, Instrument Cables, Patchcords
-
product
Cable Fault Location Equipment
Cable fault location by electromagnetic and acoustic methods (with high-voltage pulse transmitter, which is not included into the set)Detection of insulation deterioration on cables by contact and non-contact methods
-
product
Cable Fault, Test And Diagnostics
Allows an operator to test twisted pair cables for faults without physically disconnecting the cables from the switch.
-
product
Tone Generator with Cable Tracer
1RA470
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
product
Voltage Controlled Oscillator Assembly With Heater
Teledyne RF & Microwave has designed a Voltage Controlled Oscillator to replace an existing application. The oscillator covers the 520 to 560 MHz frequency range. The oscillator provides +10 to +13 dBm output power. The oscillator has internal heaters designed to maintain the oscillator assembly at constant temperature. The unit operates over the 0° to 60° C temperature range with ~200 KHz frequency variation due to temperature variation.
-
product
Lan Cable Tester
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
product
Cable Fault Point Identifier
OCFI
Shanghai Tarluz Telecom Tech Co., LTD
Optical Cable Fault Identifier (OCFI) is The latest instrument of optical cable maintenance, repair equipment developed by tarluz, it can identify the physical cable fault location easily. This is an essential tool for fiber optic cable repair!
-
product
25-meter (82 feet) Sensor Cable
E1739D
The E1739D 25-meter (82 feet) Sensor Cable is used to connect E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.
-
product
Cable Tester
The Cable Test System is a perfect example of a special solution built on existing DapTechnology building blocks. The system, which was developed with the cooperation of a key A&D cable harness supplier, replaces a cable test system with proven FireSpy Technology.
-
product
20-Pin GMCT Connector & Cable Accessories
Our 20-Pin GMCT connector is used on PXI switching products to provide a low density user connector solution.
-
product
Cable Harness EM Solver
MHARNESS
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
product
CABLE ASSY,TYPE X2,5M
763061-05
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
Cable Assembly, 2.92-mm (male) to 2.92-mm (male), 40 GHz, 36 inch
Y1740A-200
2.92-mm (male) to 2.92-mm (male), 40 GHz, 36 inch.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 2m
A050DM4-T-0A200
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
ITA, iCon, Extended Cable Clamp
410123115
This iCon ITA includes an extended cable clamp to accommodate larger cable bundles. The maximum cable bundle area = 1.97 " sq. or a 1.58"/40.13mm diameter bundle. The clamp may be inverted for smaller cable bundles.Please note: This ITA does not offer an increased bend radius that may occur with a larger cable bundle radius. Larger bend radius is offered by the iCon XL, p/n 410123232.
-
product
Assembly & Test Services
Once piece parts have been manufactured, skilled operators can kit or assemble them to the desired level. Our wiring technicians are trained to IPC standards of workmanship and operate within ESD controlled areas. We carry out both solder and crimp wire terminations along with integration of electronic components such as fans, PCBs and power supplies.
-
product
Cable Fault Locator
TW3304N
Techwin(China) Industry Co., Ltd
The Perfect Handhold Tester Series Cable Fault Locator TW3304N is the most portable test instrument in the industry. It adopts the OTDR technical principles and integrates the powerful analysis software, which enables the TW3304N fiber ranger detect fiber faults location more accurate and easy.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 1 Amp, 0.5m, 500 Port
A500RMR-T-0A050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products). Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
Sensor Cable, 5 M
E1739A
The E1739A 5-meter (16 feet) Sensor Cable is used to connect the E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.
-
product
Advanced Cable Tester v2
TP800110
The Total Phase Advanced Cable Tester v2 is the quickest and most convenient way to comprehensively test USB, Lightning, and video cables. It provides:*Short testing - Dynamic visualization of test results*Open testing - Dynamic visualization of test results*Continuity testing - Dynamic visualization of test results*DC resistance measurement for most wires, with milliohm precision on ground and power wires, ohm resolution on most other wires, continuity check only on high-speed data lines*Signal...show more -
product
Screwlock Assembly
40-969-101
This screwlock assembly can be used in LXI applications where 4 connectors are used in a horizontal row if the user requires the connectors to have a second fixing. It is also suitable for use with other products and in other situations.
-
product
Cable Assembly, 100 Pin Male SCSI to 100 Pin Male SCSI, Twisted Pair, Double Ended, 18"
515109134
Cable Assembly, 100 Pin Male SCSI to 100 Pin Male SCSI, Twisted Pair, Double Ended, 18"
-
product
Test Port Cable, 1 Mm
11500J
The Keysight 11500J test port connector has a length of 16 cm and a frequency range of DC to 110 GHz. The 11500J integrates with the Keysight N5250A network analyzer and Keysight 8510XF network analyzer systems.
-
product
Multi-function Cable Tester
NCT-100-S
*NCT-100-S Multi-Function Cable Tester Kit can help you quickly find network cables with OOK audio during network construction and maintenance. *Use TDR diagnostic technology to quickly and accurately locate fault points and accurately measure wiring diagrams and lines. Cable identification, etc.
-
product
Cable Assembly, Receiver, 36", QuadraPaddle, 160 Pin DIN FML , NI PXIe-2525
540069110240
Cable Assembly, Receiver, 36", QuadraPaddle, 160 Pin DIN FML , NI PXIe-2525.
-
product
Low Energy Cable Phasing System
Polarity Phasing Device
The Polarity Phasing Device ( P.P.D.) is a Low voltage cable phasing system for use on de-energized conductors. The Polarity Phasing Device eliminates the confusion and errors in phasing when using headsets or other makeshift techniques.
-
product
MPO Visual Cable Verifier Kit
KI-TK872
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
product
Calibration Cable, 78-pin D-type, Thermocouple Simulator Modules
40-975-078-1m
This cable assembly is specifically designed to connect to the 78-Pin D-Type port on the front panel of Pickering Interfaces Thermocouple Simulator Modules 41-760 and 41-761 enabling calibration via an external DMM.
-
product
CAT-5 Cable Equalizers
Analog Devices high speed, differential receivers and CAT-5 cable equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Our design techniques for products such as the AD8123 optimize performance for low noise, short-to-medium range applications, while also providing the high gain bandwidth required for long cable equalizations. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths.
-
product
Cable Tray, Slide Configuration, For Strain Relief And Cable Management, For 28" And Longer
310113424
Strain Relief.