Showing results: 226 - 240 of 339 items found.
-
95-525A-001 -
Pickering Interfaces Ltd.
The 95-525A-001 Plugin Breakout Module is designed to be fitted to a PXI 40-525A Signal Insertion & Monitor Matrix Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Pickering Interfaces Ltd.
The connector blocks and breakouts below are suitable to use with Pickering cards and modules that utilize a 160-pin DIN 41612 connector.
-
SEN-37002-H -
Playing With Fusion Inc
Breakout board for the Sensirion SHT31-DIS-B. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
SEN-37002-F -
Playing With Fusion Inc
Breakout board for the Sensirion SHT31-DIS-F with a built-in permeable membrane filter. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
95-193-001 -
Pickering Interfaces Ltd.
The 95-193-001 Plugin Breakout Module is designed to be fitted to a PXI 40-193 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
95-194-001 -
Pickering Interfaces Ltd.
The 95-194-001 Plugin Breakout Module is designed to be fitted to a PXI 40-194 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
95-192-001 -
Pickering Interfaces Ltd.
The 95-192-001 Plugin Breakout Module is designed to be fitted to a PXI 40-192 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Mr. BOB DLC -
Automotive Diagnostics and Publishing
Mr. BOB DLC OBD II Data Link Connector Breakout Box & Diagnostics Software for Network Waveform Viewing. This OBD2 breakout box with 8 Graphing Meter Scope like channels, is designed for the OBD2 DLC data link connector. Includes OBD II protocols such as PWM, ISO, KWP2000, 9151, J1850, VPW and CAN.
-
Pickering Interfaces Ltd.
The connector blocks and breakouts below are suitable to use with Pickering cards and modules that utilize a standard voltage 50-pin D-type connector.
-
ABex Rack ACS-003 Embedded -
Konrad Technologies GmbH
Breakout Panel for rear slots of an ABex Chassis, to feed through the connections of an embedded controller like Konrad PXIe-504. All connectors are equipped with 0.5m cable on the back side. The Breakout itself is 3 slot module (2HE 12TE) and it comes with an additional 1 slot (2HE 4TE) blank panel.
-
780041-01 -
NI
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
Electro Standards Laboratories
iagnostic tools such as Breakout Boxes/Interface Analyzers designed for use at the data interfaces of modems, multiplexers, terminals, and computers. Electro Standards Laboratories' Series of Breakout Boxes/Interface Analyzers are virtually indestructible and compatible with RS232, HSSI(SCSI-2), EIA/TIA RS530 interfaces.
-
PCI325 -
Vadatech Inc
The PCI325 is an RS-422 synchronous/asynchronous multiport serial adapter. The module can accept a clock input to synchronize the baud rate generators of each port to an external clock. All the protocol management overhead is taken care of in the hardware so that the host CPU is offloaded from managing the detailed serial protocol. An I/O breakout box may be connected to the high-density connectors of the PCI325 to provide multiple DB25, DB9, or other serial connectors for easy integration to your system or an octopus-style breakout cable may be used. The I/O breakout box may include many different status LEDs which can be tailored to your protocol/application. The PCI325 provides the breakout box with power so that it does not require any additional power cabling
-
EnsembleSeries™ RTM60P -
Mercury Systems, Inc.
*High-density connector and breakout cable to access to RS-232/RS-422 serial and 10/100/1000BASE-T Ethernet interfaces*Four 9-pin serial interfaces and four RJ45 Ethernet interfaces via the breakout cable*Standard VITA 57 FMC connectors that map to the PMC and XMC user I/O connections from the HCD6220 or HCD6410
-
Pickering Interfaces Ltd.
All of our fault insertion matrices feature a breakout arrangement that allows faults to be attached to the sensor lines via the Y axis. This includes the breaking of a connection or the adding of a series defect – all of which can simulate connectivity problems in the system. The three pin breakout versions allow the connection to be swapped for a “bad” sensor simulation.